specs

More documents

Recommendations

Info

Geotechnical Investigation South River Place, Gasser Drive, Napa 29 December 2010 ________________________________________________________________________________________________________ LIMITATIONS AND UNIFORMITY OF CONDITIONS 1. It should be noted that it is the responsibility of the owner or his representative to notify KC ENGINEERING CO., in writing, a minimum of two working days before any clearing, grading, or foundation excavation operations can commence at the site. 2. The recommendations of this report are based upon the assumption that the soil conditions do not deviate from those disclosed in the borings and from a reconnaissance of the site. Should any variations or undesirable conditions be encountered during the development of the site, KC ENGINEERING CO., will provide supplemental recommendations as dictated by the field conditions. 3. This report is issued with the understanding that it is the responsibility of the owner, or his representative, to ensure that the information and recommendations contained herein are brought to the attention of the Architect and Engineer for the project and incorporated into the plans and that the necessary steps are taken to see that the Contractor and Subcontractors carry out such recommendations in the field. 4. At the present date, the findings of this report are valid for the property investigated. With the passage of time, significant changes in the conditions of a property can occur due to natural processes or works of man on this or adjacent properties. In addition, legislation or the broadening of knowledge may result in changes in applicable standards. Changes outside of our control may render this report invalid, wholly or partially. Therefore, this report should not be considered valid after a period of two (2) years without our review, nor should it be used, or is it applicable, for any properties other than those investigated. 5. Not withstanding, all the foregoing applicable codes must be adhered to at all times. ________________________________________________________________________________________________________ KC ENGINEERING COMPANY Project No. VV3200 Page 26 of 123
APPENDIX A Vicinity Map Aerial Photo Geologic Map Site Plan Log of Test Borings Boring Log Legend Laboratory Test Results
Page 1:
PROJECT MANUAL 1807 Ross Avenue Sui
Page 5 and 6:
Napa Century Centter XD 12 - Napa,
Page 7:
Napa Century Center XD 12 - Napa, C
Page 13:
Section 15000 Section 15034 Section
Page 16 and 17:
TABLE OF CONTENTS Page 2 DIVISION 4
Page 19 and 20:
1.01 PROJECT NAPA CENTURY CENTER XD
Page 21:
E. See also Section 01600 paragraph
Page 25 and 26:
BID FORM FROM: ____________________
Page 27 and 28:
Document 00300 Page 3 CONTRACTOR: T
Page 29 and 30:
Document 00300 Page 5 Start plumbin
Page 31:
BID GUARANTEE Document 00300 Page 7
Page 35:
SECTION 00700 GENERAL CONDITIONS PA
Page 38 and 39:
Document 00800 Page 2 “Contractor
Page 40 and 41:
Document 00800 Page 4 3.18.1 In the
Page 42 and 43:
Document 00800 Page 6 7.4 In the fi
Page 44 and 45:
Document 00800 Page 8 Add Paragraph
Page 46 and 47:
A. Workers Compensation Insurance i
Page 48 and 49:
Document 00800 Page 12 Contractor i
Page 50 and 51:
Document 00800 Page 14 B. Commercia
Page 52 and 53:
Document 00800 Page 16 13.8 NO THIR
Page 54 and 55:
Document 00800 Page 18 EXHIBIT "C'
Page 56 and 57:
Document 00800 Page 20 EXHIBIT "C"
Page 58 and 59:
e. Training for Contractor personne
Page 60 and 61:
Section 01020 Page 2 1.05 ADJUSTMEN
Page 62 and 63:
Section 01340 Page 2 F. Notify Arch
Page 64 and 65:
Section 01340 Page 4 50. Painting 5
Page 66 and 67:
Appendix B REGIONALLY MANUFACTURED
Page 68 and 69:
Appendix D CERTIFIED WOOD INFORMATI
Page 70 and 71:
PART 3 EXECUTION Section 01351 Page
Page 72 and 73:
NAPA CENTURY CENTER XD 12 #165582 S
Page 74 and 75:
Section 01352 Page 2 a. Identify po
Page 76 and 77:
Section 01352 Page 4 Appendix A SAM
Page 79 and 80:
PART 1 - GENERAL SECTION 01410 TEST
Page 81 and 82:
PART 1 - GENERAL SECTION 01500 CONS
Page 83 and 84:
PART 1 - GENERAL SECTION 01600 MATE
Page 85 and 86:
Section 01600 Page 3 PROJECT: CENTU
Page 87 and 88:
PART 1 - GENERAL 1.01 REQUIREMENTS
Page 89:
PART 1 - GENERAL 1.01 RELATED WORK
Page 92 and 93:
Section 01730 Page 2 1.07 MANUAL FO
Page 94 and 95:
1.05 SUBMITTALS REQUIRED A. Submit
Page 97 and 98:
Section 01810 Page 1 SECTION 01810
Page 99 and 100:
Page 101 and 102:
Section 01811 Page 3 P. Perform fie
Page 103:
END OF SECTION Section 01811 Page 5
Page 106 and 107:
Section 02200 Page 2 G. Erect batte
Page 108 and 109:
Section 02200 Page 4 I. Place engin
Page 111 and 112:
SECTION 02362 TERMITE CONTROL PART
Page 113 and 114:
SECTION 02351 CONCRETE FOOTINGS PAR
Page 115 and 116:
SECTION 02810 PLANTING IRRIGATION P
Page 117:
3. Micro-sprinklers. 4. Bubbler-sty
Page 120 and 121:
Page 122 and 123:
Section 02825 Page 4 3.06 PROTECTIO
Page 124 and 125:
Section 02810 Page 2 4. Agenda: a.
Page 126 and 127:
2.6 SOIL CONDITIONERS Section 02810
Page 129 and 130:
SECTION 03100 STRUCTURAL CONCRETE F
Page 131 and 132:
2.08. MANUFACTURED UNITS A. Round c
Page 133 and 134:
SECTION 03200 CONCRETE REINFORCING
Page 135:
3.02. PLACEMENT Section 03200 Page
Page 138 and 139:
Section 03250 Page 2 D. Local / Reg
Page 141 and 142:
SECTION 03300 STRUCTURAL CONCRETE P
Page 143 and 144:
PART 2 - PRODUCTS Section 03300 Pag
Page 145 and 146:
Section 03300 Page 5 D. Documentati
Page 147 and 148:
Section 03300 Page 7 mixing water a
Page 149:
Section 03300 Page 9 truck during p
Page 152 and 153:
Section 03411 Page 2 Accepted sampl
Page 155 and 156:
SECTION 03600 GROUTING STEEL BASE P
Page 157 and 158:
Page 159:
Section 04100 Page 3 D. Provide mat
Page 162 and 163:
Section 04210 Page 2 d. Product Com
Page 164 and 165:
Section 04210 Page 4 B. Lay only dr
Page 166 and 167:
Section 04210 Page 6 A. Contractor
Page 168 and 169:
2. Steel Structures Painting Manual
Page 170 and 171:
Section 05100 Page 4 C. Provide pro
Page 172 and 173:
Section 05100 Page 6 (1) In accorda
Page 175 and 176:
SECTION 05200 STEEL JOISTS PART 1 -
Page 177:
PART 3 - EXECUTION Section 05200 Pa
Page 180 and 181:
Section 05300 Page 2 product during
Page 183 and 184:
SECTION 05320 METAL FLOOR DECK PART
Page 185 and 186:
SECTION 05330 COMPOSITE METAL FLOOR
Page 187 and 188:
Section 05330 Page 3 A. Composite M
Page 189 and 190:
PART 1 - GENERAL NAPA CENTURY CENTE
Page 191:
Section 05400 Page 3 F. Protective
Page 194 and 195:
Section 05500 Page 2 I. Bilco: LU-1
Page 197 and 198:
PART 1 - GENERAL SECTION 05510 STEE
Page 199:
Section 05510 Page 3 H. Dimensions
Page 202 and 203:
Section 05520 Page 2 PART 2 - PRODU
Page 205 and 206:
PART 1 - GENERAL SECTION 05721 PRE-
Page 207:
Section 05721 Page 3 3.03 FINISHING
Page 210 and 211:
Section 05810 Page 2 1.4 QUALITY AS
Page 212 and 213:
Section 05810 Page 4 3.7 SCHEDULE A
Page 214 and 215:
Section 06100 Page 2 4. Product Com
Page 217 and 218:
Page 219 and 220:
PART 1 - GENERAL SECTION 07110 MEMB
Page 221:
8. If application is not complete a
Page 224 and 225:
Section 07210 Page 2 3. Black Matt
Page 226 and 227:
Section 07410 Page 2 3. Product Val
Page 229 and 230:
PART 1 - GENERAL SECTION 07420 COMP
Page 231:
Section 07420 Page 3 2.04 FABRICATI
Page 234 and 235:
Section 07535 Page 2 will be requir
Page 236 and 237:
Section 07535 Page 4 C. The roofing
Page 239 and 240:
Page 241 and 242:
Section 07610 Page 3 B. PANEL DESIG
Page 243 and 244:
PART 1 - GENERAL SECTION 07620 SHEE
Page 245 and 246:
A PART 1 - GENERAL SECTION 07920 SE
Page 247:
D. Test adhesion to materials in th
Page 250 and 251:
Section 08100 Page 2 PART 3 - EXECU
Page 253 and 254:
Page 255:
Section 08212 Page 3 C. Accessories
Page 258 and 259:
A. Schedule deliveries to avoid del
Page 260 and 261:
2.03 FINISH HARDWARE SCHEDULE Furni
Page 262 and 263:
Section 08625 Page 2 4. Interior Fl
Page 264 and 265:
Section 08625 Page 4 years, or afte
Page 267 and 268:
PART 1 - GENERAL 1.01 SCOPE A. Prov
Page 269 and 270:
Page 271:
Section 08710 Page 5 17B Storefront
Page 274 and 275:
B. Perform glazing on dry surfaces
Page 277 and 278:
SECTION 08920 GLAZED ALUMINUM CURTA
Page 279 and 280:
Section 08920 Page 3 1.05 QUALITY A
Page 281 and 282:
PART 1- GENERAL SECTION 09220 LATH
Page 283 and 284:
O. Strip Mesh: Expanded galvanized
Page 285 and 286:
Section 09220 Page 5 7. Do plasteri
Page 287 and 288:
PART 1 - GENERAL SECTION 09250 GYPS
Page 289 and 290:
Section 09250 Page 3 2. Erect studs
Page 291 and 292:
Page 293:
Section 09310 Page 3 4. Method #4 (
Page 296 and 297:
Section 09510 Page 2 C. Deliver mat
Page 299 and 300:
PART 1 - GENERAL SECTION 09650 RESI
Page 301:
Section 09650 Page 3 B. Provide 6%
Page 304 and 305:
Section 09680 Page 2 A. Inspect the
Page 306 and 307:
Section 09800 Page 2 A. Protect adj
Page 308 and 309:
Section 09800 Page 4 3.04 CLEANING
Page 310 and 311:
Page 313 and 314:
Page 315:
Section 09950 Page 3 6. Ribs run ve
Page 318 and 319:
Page 320 and 321:
Section 09960 Page 4 D. Ferrous Met
Page 322 and 323:
Section 09960 Page 6 Coat 1: Coat 2
Page 324 and 325:
NAPA CENTURY CENTER XD 12 #165582
Page 326 and 327:
Section 10150 Page 2 1. Toilet for
Page 328 and 329:
Section 10200 Page 2 B. Shop Drawin
Page 330 and 331:
3.03 PROTECTION A. Protect installe
Page 332 and 333:
C. Attach securely using black pan
Page 334 and 335:
NAPA CENTURY CENTER XD 12 #165582
Page 336 and 337:
Section 10800 Page 2 H. Soap Dispen
Page 338 and 339:
Section 11201 Page 2 a. Landscaping
Page 340 and 341:
Section 11201 Page 4 PART 3 - EXECU
Page 342 and 343:
Section 11202 Page 2 3. Review cond
Page 345 and 346:
PART 1 - GENERAL SECTION 11400 CONC
Page 347:
2.03 ITEMIZED LIST OF EQUIPMENT A.
Page 350 and 351:
Section 12484 Page 2 1.05 QUALITY A
Page 353 and 354:
Page 355 and 356:
Section 12494 Page 3 1. Hem Pockets
Page 357 and 358:
Section 12494 Page 5 maintenance fr
Page 359 and 360:
Section 12494 Page 7 PART 3 EXECUTI
Page 361 and 362:
PART 1 GENERAL SECTION 13600 PV ELE
Page 363 and 364:
PART 1 - GENERAL SECTION 14240 HYDR
Page 365 and 366:
Section 14240 Page 3 5. Elevator Ma
Page 367 and 368:
Section 14240 Page 5 B. Cab Interio
Page 369 and 370:
Section 14240 Page 7 G. Emergency P
Page 371:
Section 14240 Page 9 A. General Con
Page 374 and 375:
J. When drawing revisions are issue
Page 376 and 377:
dates in accordance with the Genera
Page 378 and 379:
F. Starters: All starters shall be
Page 380 and 381:
A. Exterior surfaces of pipes, duct
Page 383 and 384:
SECTION 15034 HVAC TESTING AND BALA
Page 385:
satisfaction of the Architect and t
Page 388 and 389:
1.07 COORDINATION WITH OTHER WORK A
Page 390 and 391:
iron bodies for 125 lbs. WWP, all b
Page 392 and 393:
2.08 SIGNS A. Approved enameled met
Page 395 and 396:
SECTION 15400 PLUMBING PART 1 - GEN
Page 397 and 398:
C. Piping shall not penetrate demis
Page 399 and 400:
shall be responsible for structural
Page 401 and 402:
2.19 DRAINS: Refer to schedule on d
Page 403 and 404:
introduced into each line or stack.
Page 405 and 406:
SECTION 15500 HEATING, VENTILATING
Page 407 and 408:
E. Sealants within the building env
Page 409 and 410:
G. External duct insulation shall b
Page 411 and 412:
not acceptable. 5. Bearings shall b
Page 413 and 414:
2.15 START-UP OF OWNER FURNISHED IC
Page 415:
END OF SECTION Cinemark 15500 - 11
Page 418 and 419:
for further details on start-up pla
Page 420 and 421:
Temperature Controls Plumbing Recla
Page 423 and 424:
SECTION 16000 GENERAL CONDITIONS FO
Page 425 and 426:
fees required; he shall also obtain
Page 427 and 428:
. Materials of Construction c. Gage
Page 429 and 430:
A. When the Engineer has reviewed e
Page 431 and 432:
A. All necessary cutting and patchi
Page 433 and 434:
SECTION 16050 BASIC ELECTRICAL MATE
Page 435 and 436:
6. Breakers shall be bolt-on. 7. Ea
Page 437 and 438:
D. At the completion of the project
Page 439 and 440:
F. Where connection is made to any
Page 441 and 442:
C. For areas designated by Architec
Page 443 and 444:
S. The contractor shall furnish the
Page 445:
maximum time delay shall be one (1)
Page 448 and 449:
CEC California Electrical Code 1.04
Page 450 and 451:
. Calpico, Inc. c. Metraflex Co. d.
Page 452 and 453:
3.04 FIRESTOPPING A. Apply firestop
Page 455 and 456:
SECTION 16060 SITE GROUNDING AND BO
Page 457 and 458:
E. Underground Conductors: Bare, ti
Page 459 and 460:
1. Drive ground rods until tops are
Page 461:
. Equipment Rated More Than 1000 kV
Page 464 and 465:
B. Comply with 29 CFR 1910.145. 1.0
Page 466 and 467:
C. Fasteners for Labels and Signs:
Page 468 and 469:
j. Contactors. k. Remote-controlled
Page 471 and 472:
SECTION 16120 SITE CONDUCTORS AND C
Page 473 and 474:
PART 3 - EXECUTION 3.01 CONDUCTOR A
Page 475 and 476:
SECTION 16130 SITE RACEWAYS AND BOX
Page 477 and 478:
1. Alflex Inc. 2. Electri-Flex Co.
Page 479 and 480:
10. Thomas & Betts Corporation. 11.
Page 481 and 482:
1. Install concealed raceways with
Page 483 and 484: SECTION 16140 SITE WIRING DEVICES P
Page 485 and 486: . Pass & Seymour/Legrand; Wiring De
Page 487 and 488: 1. Service Outlet Assembly: Flush t
Page 489 and 490: SECTION 16400 AUXILIARY ELECTRICAL
Page 491: . The detectors shall be designed t
Page 494 and 495: 1. Dimensioned plans, elevations, s
Page 496 and 497: 2.02 MANUFACTURED UNITS A. Enclosur
Page 498 and 499: 2.07 ACCESSORY COMPONENTS AND FEATU
Page 501 and 502: SECTION 16900 AUTOMATIC TEMPERATURE
Page 503: Guaranty-Warranty. END OF SECTION C
Page 506 and 507: procedures and other requested equi
Page 509: GEOTECHNICAL INVESTIGATION REPORT o
Page 512 and 513: Geotechnical Investigation South Ri
Page 536 and 537: N Project Site KC ENGINEERING COMPA
Page 538: N Not to Scale Project Site PARTIAL
Page 541 and 542: LOG OF TEST BORING BORING NO.: 1 PR
Page 555 and 556: Client: Gasser Foundation Client No
Page 557 and 558: 120 110 100 90 80 70 60 50 40 30 20
Page 559 and 560: Particle Size Distribution Report 1
Page 567: Particle Size Distribution Report 1
Page 577: N KC ENGINEERING COMPANY 865 Cottin
Page 585 and 586:
LOG OF TEST BORING BORING NO.: 3 PR
Page 587 and 588:
Page 589 and 590:
Page 591 and 592:
Page 593 and 594:
Page 595 and 596:
865 Cotting Lane, Suite A Vacaville
Page 597:
TEST PIT NO. DEPTH (feet) 10A 0-4
Page 633:
APPENDIX B - STORMWATER MANAGEMENT
Page 636 and 637:
STORMWATER POND MODIFICATION SOUTH
Page 638 and 639:
Page 640 and 641:
Page 642 and 643:
Page 644 and 645:
Page 647:
APPENDIX C - LEED CHECKLIST NAPA CE
Page 650 and 651:
LEED 2009 New Construction Project
Page 652:
LEED 2009 New Construction Project
show all

specs

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?