specs

NAPA CENTURY CENTER XD 12
#165582
Section 02825
Page 2
D. Shop Drawings: Show layout, sizes, dimensions, details, and installation of components. Include Details of
rope attachment, tensioning methods, hardware, and tensioning and mounting methodology.
E. Samples: Submit samples of rope and/or hardware.
F. Closeout Submittals: Submit the Following:
1. Warranty: Submit manufacturer’s standard warranty documents
2. Maintenance Data: Include manufacturer’s standard cleaning and maintenance instructions to avoid
detrimental actions to finishes and performance.
1.05 QUALITY ASSURANCE
A. Qualifications:
1. Installer Qualifications: Installer should be experienced in performing work of this section and
should have specialized in installation of work similar to that required for this project.
2. Mock-Ups: Mock-Ups: Install at project site or appropriate location a job mock-up using acceptable
products and manufacturer approved installation methods. Obtain Owner’s and Architect’s approval of
product, application, and workmanship standards.
3. Pre-Installation Meetings: Conduct with Contractor, Architect, Fabricator, Installer and any other
subcontractors whose work involves cable railing system to verify project requirements, framing and
support conditions, mounting surfaces, manufacturer's installation instructions, and warranty
requirements. Comply with Division 1 requirements.
1.06 WARRANTY
A. Manufacturer’s Warranty: Submit, for Owner’s acceptance, manufacturer’s standard warranty document
executed by authorized company official.
PART 2 PRODUCTS
2.01 STAINLESS STEEL CABLE PLANT SUPPORT SYSTEM
A. Manufacturers: Subject to compliance with requirements, available manufacturers offering products that
may be incorporated into the Work include, but are not limited to, the following:
1. Carl Stahl-DécorCable Innovations LLC; I-SYS; Tel: 800-444-6271, E: sales@decorcable.com,
Web: www.decorcable.com *
2. Jakob Inc., Rope System Tel: 1-561-330-6502, E: info@jakob-usa.com, Web: www.jakob-usa.com
3. Approved Equal.
Asterisk (*) indicates manufacturer and product used as Basis of Design
B. Stainless Steel Cable Plant Support System Products:
1. Cable Rope: Product #820-0400 ASTM A492 Type 316 4mm Ø 4mm stainless steel 7x7 wire rope.
2. Spacer Bar: Product #919-120-12 AISI 304, 316 or 316L stainless steel
3. Clamp Screw for spacer: Product #923-0800 AISI 304, 316 or 316L stainless steel
4. Cover Disk w/ internal threads: Product #836-1200-80 AISI 304, 361 or 316L stainless steel
5. External Thread Swageless Connection: Product #826-0400-060 AISI 304, 361 or 316L stainless steel
a) Provide optimum adjustment in both directions by calculating final tendon lengths with
allowance for tensioning fittings with 2/3 open and with 1/3 of thread length engaged.
6. Cross Clamp Adjustable: Product #858-0400-01 AISI 304, 361 or 316L stainless steel
7. Rod for vine support: Product #922-0400 AISI 304, 361 or 316L stainless steel
8. All Fittings, Anchors, Hardware, and Accessories: AISI 304, 316 or 316L stainless steel.
C. Provide material with maximum amount of recycled content available.
2.02 FITTINGS AND ACCESSORIES
A. Accessories: Provide grommet, bushings, nuts, washers, turnbuckles, anchors, fittings and other
components as required for system installation including but not limited to
1. Rope End Fittings, Terminals, and Tensioners
2. Support Components
3. Clamps and Plant Supports
4. Anchors and Hardware