Buffalo Wild Wings
Buffalo Wild Wings
Buffalo Wild Wings
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
<strong>Buffalo</strong> <strong>Wild</strong> <strong>Wings</strong><br />
2.04 REINFORCEMENT AND ANCHORAGE<br />
A. Manufacturers of Joint Reinforcement and Anchors:<br />
1. Dur-O-Wal: www.dur-o-wal.com<br />
2. Heckmann Building Products, Inc: www.heckmannbuildingprods.com<br />
3. Hohmann & Barnard, Inc: www.h-b.com<br />
4. Masonry Reinforcing Corporation of America: www.wirebond.com<br />
5. Substitutions: See Section 01600 - Product Requirements.<br />
B. Reinforcing Steel: As indicated on the Drawings.<br />
C. Wire Positioners: Provide 9 gage wire unless noted otherwise.<br />
1. Acceptable Manufacturers and Products:<br />
a. Dur-O-Wal: D/A 811 and D/A 816.<br />
b. Hohmann & Barnard, Inc: RB and RB-Twin.<br />
c. Masonry Reinforcing Corporation of America: No. 3401 and No. 3402.<br />
D. Joint Reinforcement: Single wythe, truss type; ASTM A 82/A 82M steel wire, hot dip<br />
galvanized after fabrication to ASTM A 153/A 153M, Class B; 0.1483 inch side rods with 0.1483<br />
inch cross rods; width as required to provide not more than 1 inch and not less than 1/2 inch of<br />
mortar coverage on each exposure.<br />
E. Wall Ties: Corrugated formed sheet metal, 7/8 inch wide by 0.05 inch thick, hot dip galvanized<br />
to ASTM A 153/A 153M, Class B, sized to provide not more than 1 inch and not less than 1/2<br />
inch of mortar coverage from masonry face.<br />
F. Masonry Veneer Anchors: 2-piece anchors that permit differential movement between<br />
masonry veneer and structural backup, hot dip galvanized to ASTM A 153/A 153M, Class B.<br />
1. Anchor plates: Not less than 0.075 inch thick, designed for fastening to structural backup<br />
through sheathing by two fasteners.<br />
2. Wire ties: triangular shape, 0.1875 inch thick.<br />
3. Vertical adjustment: Not less than 2 inches.<br />
G. Stainless-Steel Drill Screws for Steel Studs: Proprietary fastener consisting of carbon-steel<br />
drill point and 300 Series stainless-steel shank, complying with ASTM C 954 except<br />
manufactured with hex washer head and neoprene or EPDM washer, No. 10 diameter by length<br />
required to penetrate steel stud flange with not less than three exposed threads.<br />
1. Acceptable Manufacturers and Products:<br />
a. Dayton Superior Corporation, Dur-O-Wal Division; Stainless Steel SX Fastener.<br />
b. ITW Buildex; Scots long life Teks.<br />
2.05 THRU-WALL FLASHING<br />
A. Thru-Wall Flashing: Copper-Laminated Flashing, 3-oz./sq. ft. copper sheet bonded between 2<br />
layers of glass-fiber cloth. Use only where flashing is fully concealed in masonry.<br />
1. Acceptable Manufacturers and Products:<br />
a. Advanced Building Products Inc.; Copper Fabric Flashing. www.abpnow.com<br />
b. Dayton Superior Corporation, Dur-O-Wal Division; Copper Fabric Thru-Wall Flashing.<br />
www.dur-o-wal.com<br />
c. Hohmann & Barnard, Inc.; H & B C-Fab Flashing. www.h-b.com<br />
2.06 ACCESSORIES<br />
A. Joint Filler: Closed cell polyvinyl chloride; oversized 50 percent to joint width; self expanding; 4<br />
inch wide by maximum lengths available.<br />
B. Building Paper: ASTM D 226, Type I ("No.15") asphalt felt.<br />
C. Weeps: Cotton rope.<br />
04-27-11 UNIT MASONRY ASSEMBLIES<br />
04810 -3
Change language