Buffalo Wild Wings
Buffalo Wild Wings
Buffalo Wild Wings
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
<strong>Buffalo</strong> <strong>Wild</strong> <strong>Wings</strong><br />
1.04 QUALITY ASSURANCE<br />
A. Perform in accordance with ASTM C 840. Comply with requirements of GA-600 for fire-rated<br />
assemblies.<br />
B. Applicator Qualifications: Company specializing in performing gypsum board application and<br />
finishing.<br />
PART 2 PRODUCTS<br />
2.01 METAL FRAMING MATERIALS<br />
A. Non-Loadbearing Framing System Components: ASTM C 645; galvanized sheet steel, of size<br />
and properties necessary to comply with ASTM C 754 for the spacing indicated, with maximum<br />
deflection of wall framing of L/240 at 5 psf.<br />
1. Exception: The minimum metal thickness and section properties requirements of ASTM C<br />
645 are waived provided steel of 40 ksi minimum yield strength is used, the metal is<br />
continuously dimpled, the effective thickness is at least twice the base metal thickness, and<br />
maximum stud heights are determined by testing in accordance with ASTM E 72 using<br />
assemblies specified by ASTM C 754.<br />
2. Studs: "C" shaped with flat or formed webs with knurled faces.<br />
3. Runners: U shaped, sized to match studs.<br />
4. Insulation Furring: Z shaped for use with board insulation, 1 1/2 inch.<br />
B. Partition Head To Structure Connections: Provide track fastened to structure with legs of<br />
sufficient length to accommodate deflection, for friction fit of studs cut short and fastened as<br />
indicated on drawings.<br />
C. Partition Head to Structure Connections: Provide mechanical anchorage devices that<br />
accommodate deflection using slotted holes, screws and anti-friction bushings, preventing<br />
rotation of studs while maintaining structural performance of partition.<br />
1. Structural Performance: Maintain lateral load resistance and vertical movement capacity<br />
required by applicable code, when evaluated in accordance with AISI North American<br />
Specification for the Design of Cold-Formed Steel Structural Members.<br />
2. Material: ASTM A 653/A 653M steel sheet, SS Grade 50/340, with G60/Z180 hot dipped<br />
galvanized coating.<br />
2.02 SUSPENDED CEILING COMPONENTS<br />
A. Hanger Wire: ASTM A 641/A 641M, Class 1 zinc coating, soft temper, 12 gauge wire.<br />
B. Flat Hangers: Steel sheet, 1 by 3/16 inch.<br />
C. Tie Wire: ASTM A 641/A 641M, Class 1 zinc coating, soft temper, 18 gauge wire.<br />
D. Ceiling Channels: 0.0312-inch, (20 Gauge) base metal thickness, with minimum 1/2-inch wide<br />
flanges.<br />
1. Depth: 2-1/2 inch.<br />
E. Furring Channels: Hat-Shaped, 2-9/16 inch wide with 1-1/4 inch face.<br />
1. Minimum Base Metal Thickness: 0.0179 inch, (25 Gauge).<br />
2. Depth: 7/8 inch or 1-1/2 inch, as indicated on Drawings.<br />
2.03 GYPSUM BOARD MATERIALS<br />
A. Acceptable Manufacturers:<br />
1. G-P Gypsum Corporation: www.gp.com.<br />
2. National Gypsum Company: www.nationalgypsum.com.<br />
3. USG Corporation: www.usg.com.<br />
4. Substitutions: See Section 01600 - Product Requirements.<br />
04-27-11 GYPSUM BOARD ASSEMBLIES<br />
09260 -2