Mechanical APDL Basic Analysis Guide - Ansys
Mechanical APDL Basic Analysis Guide - Ansys Mechanical APDL Basic Analysis Guide - Ansys
Chapter 13: Creating Geometry Displays enter POST1. See Creating Geometric Results Displays (p. 249) for more information on controlling postprocessing displays. 13.2.4.2. Displaying Boundary Condition Values Next to a Symbol You can display load symbols by using the /PBC command. (See Turning Other Symbols On and Off (p. 248) for information on turning other symbols on and off.) This command also provides an option that lets you display the boundary condition values next to the symbols. Some of the boundary condition values that are associated with this command include reaction force (RFOR), reaction moment (RMOM), displacement (U), and current flow (AMPS). Since your applied forces/moments can differ by orders of magnitude from your derived forces/moments, you can use the FBCS option of the /PSYMB command to determine the basis of the Force Boundary Conditions Scaling of your display. See the Command Reference for more information about the various boundary values that are supported. 13.2.4.3. Displaying Boundary Condition Symbols for Hidden Surfaces When there are hidden surfaces, 2-D drivers will display your boundary condition symbols, yielding a confusing display. In some instances, however, you may desire to see them. You can use the /HBC command to control BC symbol display. The default setting is to NOT display boundary condition symbols on the hidden surfaces (/HBC, WN, OFF). You can set the display ON or OFF individually for each window of your display. 3-D are not controlled by this command. This function is accessed from the Utility Menu> PlotCtrls> Style> Hidden Line Options area of the GUI. 13.2.4.4. Scaling Vector Load Symbols /VSCALE (Utility Menu> PlotCtrls> Style> Vector Arrow Scaling) allows you to adjust the scale of vector item symbols (such as the arrows representing concentrated forces, etc.). This same command also allows you to choose a "uniform scaling" option, in which all items' vector symbols have the same length, regardless of their relative magnitudes. 13.2.4.5. Turning Other Symbols On and Off You can turn symbols for master degrees of freedom, coupled nodes, and nodes in constraint equations on and off with the /PBC command. Use the /PSYMB command (Utility Menu> PlotCtrls> Symbols) to turn symbols on and off for local, nodal, and element coordinate systems, line directions, keypoints/nodes, and layer orientation (for layered elements). 248 Release 13.0 - © SAS IP, Inc. All rights reserved. - Contains proprietary and confidential information of ANSYS, Inc. and its subsidiaries and affiliates.
Chapter 14: Creating Geometric Results Displays In a geometric results display, you can review your solution results in a postprocessing display of your model's elements. The following geometric results display topics are available: 14.1. Using the GUI to Display Geometric Results 14.2. Options for Creating Geometric Results Displays 14.3. Changing the Specifications for POST1 Results Displays 14.4. Q-Slice Techniques 14.5. Isosurface Techniques 14.6. Controlling Particle Flow or Charged Particle Trace Displays 14.1. Using the GUI to Display Geometric Results The choice of geometric results displays includes displaced shapes, results contours (including line-element "contours," such as moment diagrams), and vector (arrow) results (such as thermal flux vector displays). These displays are available only within POST1, the general postprocessor. The following figure illustrates a typical geometric results display: Figure 14.1 Contour Results Plot The most convenient way to create and control geometric results displays is by using the functions available under Utility Menu> Plot and Utility Menu> PlotCtrls. Alternatively, you can use graphics action and control commands, as described in the following subsections. Release 13.0 - © SAS IP, Inc. All rights reserved. - Contains proprietary and confidential information of ANSYS, Inc. and its subsidiaries and affiliates. 249
- Page 213 and 214: !derivative of variable 2 with resp
- Page 215 and 216: The above command assumes that you
- Page 217 and 218: When plotting complex data such as
- Page 219 and 220: Sample Output from EXTREM time-hist
- Page 221 and 222: 5. Select the variables to be opera
- Page 223 and 224: RESP requires two previously define
- Page 225 and 226: Chapter 9: Selecting and Components
- Page 227 and 228: Note Crossover commands for selecti
- Page 229 and 230: would put UX and UZ constraints on
- Page 231 and 232: The Command Reference describes the
- Page 233 and 234: Chapter 10: Getting Started with Gr
- Page 235 and 236: Remote Network Access Hidden Line R
- Page 237 and 238: 10.4.1. Adjusting Input Focus To en
- Page 239 and 240: • If the environment variable SB_
- Page 241 and 242: 10.5.5. Erasing the Current Display
- Page 243 and 244: Chapter 11: General Graphics Specif
- Page 245 and 246: 11.3.1. Changing the Viewing Direct
- Page 247 and 248: 11.4. Controlling Miscellaneous Tex
- Page 249 and 250: 11.4.3. Controlling the Location of
- Page 251 and 252: Chapter 12: PowerGraphics Two metho
- Page 253 and 254: The subgrid approach affects both t
- Page 255 and 256: Chapter 13: Creating Geometry Displ
- Page 257 and 258: Figure 13.1 Element Plot of SOLID65
- Page 259 and 260: 13.2.1.12. Vector Versus Raster Mod
- Page 261 and 262: Figure 13.2 Create Best Quality Ima
- Page 263: 13.2.3.2. Choosing a Format for the
- Page 267 and 268: Figure 14.2 A Typical ANSYS Results
- Page 269 and 270: • Changing the contour interval.
- Page 271 and 272: 14.5. Isosurface Techniques Isosurf
- Page 273 and 274: Chapter 15: Creating Graphs If you
- Page 275 and 276: Establishing separate Y-axis scales
- Page 277 and 278: 15.2.3.5. Defining the TIME (or, Fo
- Page 279 and 280: Chapter 16: Annotation A common ste
- Page 281 and 282: 16.3. 3-D Annotation 3-D text and g
- Page 283 and 284: Chapter 17: Animation Animation is
- Page 285 and 286: • ANMODE (Utility Menu> PlotCtrls
- Page 287 and 288: Figure 17.2 The Animation Controlle
- Page 289 and 290: Note If you are doing animation fro
- Page 291 and 292: Chapter 18: External Graphics Besid
- Page 293 and 294: 18.1.4. Exporting Graphics in UNIX
- Page 295 and 296: Note The commands discussed in this
- Page 297 and 298: 18.3.6. Editing the Neutral Graphic
- Page 299 and 300: Chapter 19: The Report Generator Th
- Page 301 and 302: 2. Specify a caption for the captur
- Page 303 and 304: 19.4.1.1. Creating a Custom Table I
- Page 305 and 306: Table ID 46 47 48 Description Compo
- Page 307 and 308: Button or Field DYNAMIC DATA REPORT
- Page 309 and 310: The HTML tag to begin JavaScript co
- Page 311 and 312: listingName A unique listing name a
- Page 313 and 314: Chapter 20: File Management and Fil
Chapter 13: Creating Geometry Displays<br />
enter POST1. See Creating Geometric Results Displays (p. 249) for more information on controlling postprocessing<br />
displays.<br />
13.2.4.2. Displaying Boundary Condition Values Next to a Symbol<br />
You can display load symbols by using the /PBC command. (See Turning Other Symbols On and Off (p. 248)<br />
for information on turning other symbols on and off.) This command also provides an option that lets you<br />
display the boundary condition values next to the symbols. Some of the boundary condition values that are<br />
associated with this command include reaction force (RFOR), reaction moment (RMOM), displacement (U),<br />
and current flow (AMPS).<br />
Since your applied forces/moments can differ by orders of magnitude from your derived forces/moments,<br />
you can use the FBCS option of the /PSYMB command to determine the basis of the Force Boundary Conditions<br />
Scaling of your display.<br />
See the Command Reference for more information about the various boundary values that are supported.<br />
13.2.4.3. Displaying Boundary Condition Symbols for Hidden Surfaces<br />
When there are hidden surfaces, 2-D drivers will display your boundary condition symbols, yielding a confusing<br />
display. In some instances, however, you may desire to see them. You can use the /HBC command<br />
to control BC symbol display. The default setting is to NOT display boundary condition symbols on the hidden<br />
surfaces (/HBC, WN, OFF). You can set the display ON or OFF individually for each window of your display.<br />
3-D are not controlled by this command. This function is accessed from the Utility Menu> PlotCtrls> Style><br />
Hidden Line Options area of the GUI.<br />
13.2.4.4. Scaling Vector Load Symbols<br />
/VSCALE (Utility Menu> PlotCtrls> Style> Vector Arrow Scaling) allows you to adjust the scale of vector<br />
item symbols (such as the arrows representing concentrated forces, etc.). This same command also allows<br />
you to choose a "uniform scaling" option, in which all items' vector symbols have the same length, regardless<br />
of their relative magnitudes.<br />
13.2.4.5. Turning Other Symbols On and Off<br />
You can turn symbols for master degrees of freedom, coupled nodes, and nodes in constraint equations on<br />
and off with the /PBC command. Use the /PSYMB command (Utility Menu> PlotCtrls> Symbols) to turn<br />
symbols on and off for local, nodal, and element coordinate systems, line directions, keypoints/nodes, and<br />
layer orientation (for layered elements).<br />
248<br />
Release 13.0 - © SAS IP, Inc. All rights reserved. - Contains proprietary and confidential information<br />
of ANSYS, Inc. and its subsidiaries and affiliates.