reprap-granule-extruder-tudelft1

Recommendations

Info

A | Blender <strong>granule</strong> tests 11. Blending entire milk bottle, first in 1 piece, then cut into 2 pieces, then 4. Until the blender is able to blend the milk bottle into small pieces. Input Blender Output Thoughts As we expected the first time we blended the material it was stuck, this effect remained until we cut the material for the fourth time into 8 pieces. - The blades could not shred the screw thread part of the bottle. - Small amount of material out of one bottle, what can you make out of one bottle? - Pieces of the bottle cannot be bigger than the width of the blender - Can a layer of water keep the material from bouncing up and down and cool down the metal blades and material 12. Blending 1 minute, couple of large crumpled pieces (±10gram) inside a blender with water (so that the pieces are just “below” water level, material floats) Input Blender Output Thoughts We used as input the size and shape where we thought we had the best result with: the result of test number 4. The result was even better than that test. As result we had nearly only small parts. - Water keeps the part from bouncing. - Knifes didn’t feel warm, we wonder if this is also at the moment of impact and after a long time of use. 36 | Prototyping Lab (IO3028) - RepRap Recycle Add-on
A | Blender <strong>granule</strong> tests 13. Blending 1 minute, couple of large crumpled pieces (±10gram) inside a blender with water (so that the pieces are above water level) Input Blender Output Thoughts We used as input the size and shape wh3ere we thought we had the best result with. As result we had nearly only small parts. - Test result was a bit better than test number 12. - Knifes did not feel warm, we wonder if this is also at moment of impact and after a long time of use 37 | Prototyping Lab (IO3028) - RepRap Recycle Add-on
Page 1 and 2: Developing a plastics recycling add
Page 3 and 4: Table of Contents 1. Introduction 5
Page 5 and 6: 1 İntroduction The RepRap is a 3D
Page 7 and 8: 2 | The RepRap project Fused deposi
Page 9 and 10: 3 | From product to granule Possibl
Page 11 and 12: 3 | From product to granule Figure
Page 13 and 14: 3 | From product to granule As for
Page 15 and 16: 4 | From granule to extrusion decre
Page 17 and 18: 4 | From granule to extrusion threa
Page 19 and 20: 4 | From granule to extrusion screw
Page 21 and 22: 4 | From granule to extrusion Figur
Page 23 and 24: 5 Ȧdapting the prototype to the Re
Page 25 and 26: 6 Ċonclusion and discussion The ma
Page 27 and 28: 7 Ṙecommendations for further dev
Page 29 and 30: 8 Ṙeferences 1 - Bowyer, A. 1992.
Page 31 and 32: Appendix A Blender granule tests 1.
Page 33 and 34: A | Blender granule tests 5. Blendi
Page 35: - Granule still bounces up without
Page 39 and 40: Appendix B. Technical drawings of t
Page 41 and 42: 50 5 5 10 25 50 50 10 R8 5 25 1 10
Page 43 and 44: M16 20 25 14 2 30° 7 nozzle benami
Page 45 and 46: Appendix C. Extrusion screw manufac

reprap-granule-extruder-tudelft1

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?