reprap-granule-extruder-tudelft1

Recommendations

Info

8 | References 26 - HowStuffWorks. 2010. Types of Blenders. [Online] Available at: http://home.howstuffworks.com/blender2.htm [Accessed 17 March 2010] 27 - Fab Lab Central. 2010. Fab Lab FAQ. [Online] Available at: http://fab.cba.mit.edu/about/faq/ [Accessed 14 April 2010] 28 - Maddock, B.H. 1974. Extruder Scale-Up by Computer. Polymer Engineering and Science, 14(12). 29 - Covas, J.A. et al. 2004. A miniatore extrusion line, for small scale processing studies. 30 - Bin, L. et al. 2009. Research on micro-extrusion characteristic of mini-screw in the screw extruding spray head. 31 - RepRap.org, Bowyer, A. 2007. GranuleExtruder - RepRapWiki. [Online] Available at: http://reprap.org/bin/view/Main/GranuleExtruder [Accessed 9 February 2010] 32 - Higgs, F. 2006. Initial experiments on filament extruder 2.0. [Online] Available at: http://blog.reprap.org/2006/02/initial-experiments-on-filament.html [Accessed 10 March 2010] 33 - Tan, A. and Nixon, T. 2007. Rapid prototype manufacturing system. University of Adelaide. [Online] Available at: http://fabathome.org/wiki/uploads/c/cd/Rapid_Prototype_Manufacturing_System_-_Timothy_ Nixon_&_Adrian_Tan_2007.pdf [Accessed 10 March 2010] 34 - RepRap.org. 2010. ThermoplastExtruder 2.0 - RepRapWiki. [Online] Available at: http://reprap.org/wiki/ThermoplastExtruder_2_0 [Accessed 20 March 2010] 35 - MakerBot Industries. 2010. NEMA 23 Stepper Motor. [Online] Available at: http://store.makerbot.com/featured-products/stepper-motor-nema-23-kelingkl23h51-24-08b.html [Accessed 20 March 2010] 30 | Prototyping Lab (IO3028) - RepRap Recycle Add-on
Appendix A Blender granule tests 1. Blending 1 minute, one large flat piece (size around 13cm x 5,5cm) Input Blender Output Thoughts The result was not that good; the piece has only been cut a couple of times. - Would the blades cut well if we crumpled the material? - Would the blades cut well if we put more material into the blender? 2. Blending 1 minute, one large crumpled piece (size around 13cm x 5,5cm) Input Blender Output Thoughts Result; there were still to many large pieces, but the result was a lot better. - What size is small enough to extrude? - How can we cut the remaining parts, putting more material into the blender? 31 | Prototyping Lab (IO3028) - RepRap Recycle Add-on
Page 1 and 2: Developing a plastics recycling add
Page 3 and 4: Table of Contents 1. Introduction 5
Page 5 and 6: 1 İntroduction The RepRap is a 3D
Page 7 and 8: 2 | The RepRap project Fused deposi
Page 9 and 10: 3 | From product to granule Possibl
Page 11 and 12: 3 | From product to granule Figure
Page 13 and 14: 3 | From product to granule As for
Page 15 and 16: 4 | From granule to extrusion decre
Page 17 and 18: 4 | From granule to extrusion threa
Page 19 and 20: 4 | From granule to extrusion screw
Page 21 and 22: 4 | From granule to extrusion Figur
Page 23 and 24: 5 Ȧdapting the prototype to the Re
Page 25 and 26: 6 Ċonclusion and discussion The ma
Page 27 and 28: 7 Ṙecommendations for further dev
Page 29: 8 Ṙeferences 1 - Bowyer, A. 1992.
Page 33 and 34: A | Blender granule tests 5. Blendi
Page 35 and 36: - Granule still bounces up without
Page 37 and 38: A | Blender granule tests 13. Blend
Page 39 and 40: Appendix B. Technical drawings of t
Page 41 and 42: 50 5 5 10 25 50 50 10 R8 5 25 1 10
Page 43 and 44: M16 20 25 14 2 30° 7 nozzle benami
Page 45 and 46: Appendix C. Extrusion screw manufac

reprap-granule-extruder-tudelft1

Create successful ePaper yourself

Delete template?

Save as template?