CA Dynam for VSE User Guide
CA Dynam for VSE User Guide CA Dynam for VSE User Guide
Vault Location Control Program—TDYNVLT INCLVLT=(x,x,.....x,x) Selects the vault locations to be reported on. If you omit this operand, TDYNVLT reports on the following: • All vault locations, unless EXCLVLT is defined • All vault locations except those defined by EXCLVLT EXCLVLT=(x,x,.....x,x) Indicates which vault locations to leave out of the report. If you omit this operand, TDYNVLT reports on the following: • All vault locations, unless INCLVLT is defined • Only vault locations defined in INCLVLT MDSN= Determines which data set names of a multifile volume are to be listed on the report. YES NO Prints all the data set names of a multifile volume. Prints only the first data set name. The default is NO. If the report sequence is based on data set name, it is always based on the first data set name of a multifile. EXTRACT Creates a file (with a ddname of CAIEXTR), that contains a list of all the tapes in the Catalog. This command should be executed only once. Note: The TDYNIBM program EJECT command can be used to read the CAIEXTR file and eject volumes from the 3494 Tape Library. For more information, see IBM 3494 Tape Library Interface. Inventory Report Location Inventory (Verification) Report (TDYNVLT-05) Lists all tapes in each vault. TDYNVLT can generate this report for all or specific vault locations. If the report is by volume serial number, it lists only the first data set of a multifile, unless you specify MDSN=YES. 3–50 User Guide
Vault Location Control Program—TDYNVLT MOVEMENT and VERIFY Commands MOVEMENT Command The format for the MOVEMENT command is: MOVement {EXTRACT|DUMmy|TRace } VERIFY Command The format for the VERIFY command is: VERify {DUMmy|TRace } Command Parameters The parameters for the MOVEMENT and VERIFY commands follow. EXTRACT Must be the only parameter specified. Creates a file with a ddname of CAIEXTR, which contains a list of all the tapes in the Catalog. Note: The TDYNIBM program EJECT command can be used to read the CAIEXTR file and eject volumes from the 3494 Tape Library. For more information, see IBM 3494 Tape Library Interface. DUMMY TRACE Does not update the Catalog. Supplies a trace of all Catalog updates. Movement Reports Location Exit Report (TDYNVLT-01) TDYNVLT generates this report every time volumes are moved from one location to another. It produces up to 26 different Location Exit reports, one for each location under its control. Location Entry Report (TDYNVLT-02) TDYNVLT generates this report every time volumes are moved from one location to another. It produces up to 26 different Location Entry reports, one for each location under its control. Movement Summary Report (TDYNVLT-03) TDYNVLT lists, by volume serial number, all tapes that have been transferred. This is primarily for auditing or historical purposes. Vault Exception Report (TDYNVLT-04) TDYNVLT lists all tapes in vaults other than the one specified for normal rotation. This occurs because of one of the following: • DYNCAT specifies PERM=YES • TDYNVLT includes the VERIFY option Chapter 3: Supporting Tape File Management 3–51
- Page 117: Using the Console Alarm Facility IB
- Page 120 and 121: Tape File Management Utilities Usin
- Page 122 and 123: Tape File Management Utilities Note
- Page 124 and 125: Tape File Management Utilities The
- Page 126 and 127: Tape File Management Utilities TDYN
- Page 128 and 129: Tape File Management Utilities UPSI
- Page 130 and 131: Tape File Management Utilities // J
- Page 132 and 133: Tape File Management Utilities TEST
- Page 134 and 135: Tape File Management Utilities The
- Page 136 and 137: Tape File Management Utilities The
- Page 138 and 139: Tape File Management Utilities CATN
- Page 140 and 141: Tape File Management Utilities Exam
- Page 142 and 143: Tape File Management Utilities VER
- Page 144 and 145: Tape File Management Utilities SYST
- Page 146 and 147: Reporting on Tape Files The TDYNUTL
- Page 148 and 149: Reporting on Tape Files The followi
- Page 150 and 151: Reporting on Tape Files In addition
- Page 152 and 153: Reporting on Tape Files TDYNPULL Pr
- Page 154 and 155: Reporting on Tape Files UNCONTROLLE
- Page 156 and 157: Reporting on Tape Files Note: • S
- Page 158 and 159: Reporting on Tape Files This job st
- Page 160 and 161: Reporting on Tape Files Important!
- Page 162 and 163: Reporting on Tape Files PED AS-OF-D
- Page 164 and 165: Vault Location Control Program—TD
- Page 166 and 167: Vault Location Control Program—TD
- Page 170 and 171: IBM 3494 Tape Library Interface IBM
- Page 172 and 173: IBM 3494 Tape Library Interface Not
- Page 174 and 175: IBM Virtual Tape Facility (VTAPE) S
- Page 176 and 177: IBM Virtual Tape Facility (VTAPE) S
- Page 178 and 179: IBM Virtual Tape Facility (VTAPE) S
- Page 180 and 181: IBM Virtual Tape Facility (VTAPE) S
- Page 182 and 183: Basic Components The enhanced VTOC
- Page 184 and 185: Basic Components Disk Space Availab
- Page 186 and 187: Basic Components Method Two Submitt
- Page 188 and 189: Basic Components Overriding Catalog
- Page 190 and 191: Managing the VTOC Default Allocatio
- Page 192 and 193: Managing the VTOC Searching the VTO
- Page 194 and 195: Defining File ID Option Codes Defin
- Page 196 and 197: Defining File ID Option Codes F Fra
- Page 198 and 199: Defining File ID Option Codes O Old
- Page 200 and 201: Controlling Generation Data Sets //
- Page 202 and 203: Controlling Generation Data Sets De
- Page 204 and 205: Automatic Volume Assignment and Rec
- Page 206 and 207: Selecting Logical Units LUB Availab
- Page 208 and 209: Modifying Logical Unit Assignments
- Page 210 and 211: Controlling Disk Pools To catalog a
- Page 212 and 213: Controlling Disk Pools For example,
- Page 214 and 215: Allocating Space across Generic Vol
- Page 216 and 217: Recovering from Lack of Allocated S
Vault Location Control Program—TDYNVLT<br />
MOVEMENT and VERIFY Commands<br />
MOVEMENT Command The <strong>for</strong>mat <strong>for</strong> the MOVEMENT command is:<br />
MOVement {EXTRACT|DUMmy|TRace }<br />
VERIFY Command<br />
The <strong>for</strong>mat <strong>for</strong> the VERIFY command is:<br />
VERify {DUMmy|TRace }<br />
Command Parameters<br />
The parameters <strong>for</strong> the MOVEMENT and VERIFY commands follow.<br />
EXTRACT<br />
Must be the only parameter specified. Creates a file with a ddname of<br />
<strong>CA</strong>IEXTR, which contains a list of all the tapes in the Catalog.<br />
Note: The TDYNIBM program EJECT command can be used to read the<br />
<strong>CA</strong>IEXTR file and eject volumes from the 3494 Tape Library. For more<br />
in<strong>for</strong>mation, see IBM 3494 Tape Library Interface.<br />
DUMMY<br />
TRACE<br />
Does not update the Catalog.<br />
Supplies a trace of all Catalog updates.<br />
Movement Reports<br />
Location Exit Report (TDYNVLT-01)<br />
TDYNVLT generates this report every time volumes are moved from one<br />
location to another. It produces up to 26 different Location Exit reports, one<br />
<strong>for</strong> each location under its control.<br />
Location Entry Report (TDYNVLT-02)<br />
TDYNVLT generates this report every time volumes are moved from one<br />
location to another. It produces up to 26 different Location Entry reports, one<br />
<strong>for</strong> each location under its control.<br />
Movement Summary<br />
Report<br />
(TDYNVLT-03)<br />
TDYNVLT lists, by volume serial number, all tapes that have been<br />
transferred. This is primarily <strong>for</strong> auditing or historical purposes.<br />
Vault Exception Report (TDYNVLT-04)<br />
TDYNVLT lists all tapes in vaults other than the one specified <strong>for</strong> normal<br />
rotation. This occurs because of one of the following:<br />
• DYN<strong>CA</strong>T specifies PERM=YES<br />
• TDYNVLT includes the VERIFY option<br />
Chapter 3: Supporting Tape File Management 3–51