Crystal - cs5336.pdf

CS5336, CS5338, CS5339
ANALOG CHARACTERISTICS (Logic 0 = GND; Logic 1 = VD+; K grade: TA = 25°C; B and T
grades: TA = TMIN to TMAX; VA+, VL+,VD+ = 5V; VA- = -5V; Full-Scale Input Sinewave, 1kHz; Output word
rate = 48 kHz; SCLK = 3.072 MHz; Source Impedance = 50Ω with 10 nF to AGND; Measurement Bandwidth is
10 Hz to 20 kHz; unless otherwise specified.)
CS5336,8,9-K CS5336-B CS5336-T
Parameter Symbol Min Typ Max Min Typ Max Min Typ Max Units
Specified Temperature Range TA 0 to 70 -40 to +85 -55 to +125 °C
Resolution 16 - - 16 - - 16 - - Bits
Dynamic Performance
Dynamic Range 92.7 95.7 - 90 93.5 - 84 92 - dB
Signal-to-(Noise + Distortion); THD+N S/(N+D) 90.7 92.7 - 85 89 - 82 86 - dB
Signal to Peak Noise - 96 - - 95 - - 94 - dB
Total Harmonic Distortion THD .0025 .001 - .005 .001 - .013 .005 - %
Interchannel Phase Deviation - .0001 - - .0001 - - .0001 - °
Interchannel Isolation (dc to 20 kHz) 100 106 - 90 106 - 83 96 - dB
dc Accuracy
Interchannel Gain Mismatch - 0.01 0.05 - .01 .05 - .01 0.1 dB
Gain Error (includes Vref tolerance) - ±1 ±5 - ±2 ±5 - ±3 ±6 %
Gain Drift (includes Vref drift, Note 1) - 25 - - 70 - - 70 - ppm/°C
Bipolar Offset Error (Note 2) - ±5 ±15 - ±10 ±30 - ±16 ±65 LSB
Offset Drift (Note1) - 15 - - 20 - - 20 - ppm/°C
Analog Input
Input Voltage Range (±Full Scale) VIN ±3.5 ±3.68 - ±-3.5 ±3.68 - ±3.5 ±3.68 - V
Input Impedance ZIN - 65 - - 65 - - 65 - kΩ
Power Supplies
Power Supply Current (VA+)+(VL+) IA+ - 25 35 - 25 35 - 25 35 mA
with APD, DPD low VA- IA- - -25 -35 - -25 -35 - -25 -35 mA
(Normal Operation) VD+ ID+ - 30 45 - 30 45 - 30 50 mA
Power Supply Current (VA+)+(VL+) IA+ - 10 50 - 10 50 - 10 50 µA
with APD, DPD high VA- IA- - -10 -50 - -10 -50 - -10 -50 µA
(Power-Down Mode) VD+ ID+ - 10 400 - 10 400 - 10 400 µA
Power Consumption (APD, DPD Low) PDN - 400 575 - 400 575 - 400 600 mW
(APD, DPD High) PDS - 0.15 2.5 - 0.15 2.5 - 0.15 2.5 mW
Power Supply
(dc to 26 kHz)
PSRR
- 54 - - 54 - - 54 - dB
Rejection Ratio (26 kHz to 3.046 MHz) - 100 - - 100 - - 100 - dB
Notes: 1. This parameter is guaranteed by design and/or characterization.
2. After calibration with DCAL connected to ACAL, and ZEROL & ZEROR terminated to AGND with an
impedance matched to the AINR & AINL source impedance. Executing a calibration with ACAL tied
low (See Power Down and Offset Calibration section) will yield an offset error of typically less than
± 5LSB.
Specifications are subject to change without notice.
3-40 DS23F1