Emotron FDU 2.0 Variable Speed Drive
Emotron FDU 2.0 Variable Speed Drive Emotron FDU 2.0 Variable Speed Drive
Addendum PWM Random [22E3] Default: Off Off 0 Random modulation is Off. On 1 Communication information 11.3.5 Speed [340] Revised selections for menu [343]. Random modulation is active. Random frequency variation range is ± 1/8 of level set in [E22E1]. Modbus Instance no/DeviceNet no: 43055 Profibus slot/index 168/214 Fieldbus format Modbus format 22E3 PWM Random Stp Off A UInt UInt Maximum speed [343] Sets the maximum speed. The maximum speed will operate as an absolute maximum limit. This parameter is used to prevent damage due to high speed. The synchronous speed (Sync Speed) is determined by the motor speed [225]. Keyboard reference Mode[369] Changed default value from Normal to MotPot Default: Normal 0 .... MotPot 1 .... Mot Pot 11.5.3 Analogue Outputs [530] Added selections in Menu [531] and [534] AnOut1 Function [531] and AnOut 2 Function [534] Added selections Speed Ref and Torque Ref Default: Speed Speed Ref 14 Torque Ref 15 369 Key Ref Mode StpA MotPot 531 AnOut 1 FC StpA Speed Actual internal speed reference Value after ramp and V/Hz. Actual torque reference value (=0 in V/Hz mode) Default: Sync Speed 0 343 Max Speed StpA Sync Speed Sync Speed Synchronous speed, i.e. no load speed, at nominal frequency. 1-24000rpm 1- 24000 Min Speed - 4 x Motor Sync Speed Communication information Modbus Instance no/DeviceNet no: 43123 Profibus slot/index 169/27 Fieldbus format Modbus format Int, 1=1 rpm UInt Note: Maximum speed [343] has priority over Min Speed [341], i.e. if [343] is set below [341] then the drive will run at [343] Max Speed with acceleration times given by [335] and [336] respectively. 11.3.7 Preset References [360] New default value in Menu [369] Emotron AB 01-4934-01r1 Other changes 5
Addendum 14. Technical Data 14.1 Electrical specifications related to model New models for VFX2.0 and FDU2.0 with 480V rated voltage. The 228 Amp unit is the largest unit in frame size F available with UL approval Model Max. output current [A] * Normal duty (120%, 1 min every 10 min) Power@ 400 V [kW] Power@ 460 V [hp] Rated current [A] Heavy duty (150%, 1 min every 10 min) Power@ 400 V [kW] Power@ 460 V [hp] Rated current [A] Frame size FDU/VFX 48-228 300 110 200 228 90 150 182 F * Available during limited time and as long as allowed by drive temperature. Emotron AB 01-4934-01r1 2009-10-30 Emotron AB, Mörsaregatan 12, SE-250 24 Helsingborg, Tel: +46 42 16 99 00, Fax: +46 42 16 99 49 www.emotron.com
- Page 1 and 2: Emotron FDU 2.0 Variable Speed Driv
- Page 3 and 4: Addendum 11.3.4. Mechanical brake c
- Page 5: Addendum 2. Other changes In follow
- Page 10 and 11: Safety Instructions Instruction man
- Page 12 and 13: Contents Safety Instructions ......
- Page 14 and 15: 1. Introduction FDU is used most co
- Page 16 and 17: Table 1 Standards European All USA
- Page 18 and 19: 2. Mounting This chapter describes
- Page 20 and 21: 2.2.2 Mounting schemes 128,5 24,8 1
- Page 22 and 23: Table 5 Flow rates cooling fans Cab
- Page 24 and 25: 3. Installation The description of
- Page 26 and 27: VSD built into cabinet Litz RFI-Fil
- Page 28 and 29: 3.4 Cable specifications Table 7 Ca
- Page 30 and 31: 4. Control Connections 4.1 Control
- Page 32 and 33: 4.4 Connection example Fig. 29 give
- Page 34 and 35: 4.5.2 Types of control signals Alwa
- Page 36 and 37: 5. Getting Started This chapter is
- Page 38 and 39: 5.4 Local control Manual control vi
- Page 40 and 41: 6. Applications This chapter contai
- Page 42 and 43: 7. Main Features This chapter conta
- Page 44 and 45: 7.1.6 Preset references The VSD is
- Page 46 and 47: See Fig. 40. The Enable and Stop in
- Page 48 and 49: . Torque [%] [4161] MaxAlarmMar (15
- Page 50 and 51: 7.6.2 Fixed MASTER This is the defa
- Page 52 and 53: 7.6.6 PID control When using the Pu
- Page 54 and 55: 7.6.8 Checklist And Tips 1. Main Fu
Addendum<br />
PWM Random [22E3]<br />
Default:<br />
Off<br />
Off 0 Random modulation is Off.<br />
On 1<br />
Communication information<br />
11.3.5 <strong>Speed</strong> [340]<br />
Revised selections for menu [343].<br />
Random modulation is active. Random frequency<br />
variation range is ± 1/8 of level set<br />
in [E22E1].<br />
Modbus Instance no/DeviceNet no: 43055<br />
Profibus slot/index 168/214<br />
Fieldbus format<br />
Modbus format<br />
22E3 PWM Random<br />
Stp Off<br />
A<br />
UInt<br />
UInt<br />
Maximum speed [343]<br />
Sets the maximum speed. The maximum speed will operate<br />
as an absolute maximum limit. This parameter is used to<br />
prevent damage due to high speed. The synchronous speed<br />
(Sync <strong>Speed</strong>) is determined by the motor speed [225].<br />
Keyboard reference Mode[369]<br />
Changed default value from Normal to MotPot<br />
Default:<br />
Normal 0 ....<br />
MotPot 1 ....<br />
Mot Pot<br />
11.5.3 Analogue Outputs [530]<br />
Added selections in Menu [531] and [534]<br />
AnOut1 Function [531] and AnOut 2 Function<br />
[534]<br />
Added selections <strong>Speed</strong> Ref and Torque Ref<br />
Default: <strong>Speed</strong><br />
<strong>Speed</strong> Ref 14<br />
Torque Ref 15<br />
369 Key Ref Mode<br />
StpA<br />
MotPot<br />
531 AnOut 1 FC<br />
StpA<br />
<strong>Speed</strong><br />
Actual internal speed reference Value<br />
after ramp and V/Hz.<br />
Actual torque reference value<br />
(=0 in V/Hz mode)<br />
Default:<br />
Sync <strong>Speed</strong> 0<br />
343 Max <strong>Speed</strong><br />
StpA<br />
Sync <strong>Speed</strong><br />
Sync <strong>Speed</strong><br />
Synchronous speed, i.e. no load<br />
speed, at nominal frequency.<br />
1-24000rpm 1- 24000 Min <strong>Speed</strong> - 4 x Motor Sync <strong>Speed</strong><br />
Communication information<br />
Modbus Instance no/DeviceNet no: 43123<br />
Profibus slot/index 169/27<br />
Fieldbus format<br />
Modbus format<br />
Int, 1=1 rpm<br />
UInt<br />
Note: Maximum speed [343] has priority over Min <strong>Speed</strong><br />
[341], i.e. if [343] is set below [341] then the drive will<br />
run at [343] Max <strong>Speed</strong> with acceleration times given by<br />
[335] and [336] respectively.<br />
11.3.7 Preset References [360]<br />
New default value in Menu [369]<br />
<strong>Emotron</strong> AB 01-4934-01r1 Other changes 5