Emotron MSF 2.0 Fieldbus Option
Emotron MSF 2.0 Fieldbus Option Emotron MSF 2.0 Fieldbus Option
1. Quick Set-up Following flowchart is a step by step guide for advanced users, with references to chapters with detailed information. Set FieldBus I/O Address - Profibus, see 4.2.3 - DeviceNet, see 5.2.3 Set FieldBus I/O Baudrate - Profibus, automatically selected - DeviceNet, see 5.2.4 Set internal Communication Address - MSF, use address 1, see 7.4 Set internal Communication Baudrate - MSF, use 19.2 kBaud, see 7.4 Set Internal Communication Parity - MSF, use No Parity, see 7.4 Set Control Mode - MSF, parameter 200, use mode 3, see 7.5 Fig. 1 Step by step guide. CG Drives & Automation 01-5927-01r0 Quick Set-up 3
4 Quick Set-up CG Drives & Automation 01-5927-01r0
- Page 1 and 2: Emotron MSF 2.0 Fieldbus Option Ins
- Page 4 and 5: Safety Instruction manual It is imp
- Page 6 and 7: Contents Safety ...................
- Page 10 and 11: 2. General 2.1 Introduction The Fie
- Page 12 and 13: 3. FieldBus I/O 3.1 Introduction Th
- Page 14 and 15: 3.5.2 LED indication Four LED´s in
- Page 16 and 17: 4. ProfiBus - Dp 4.1 Introduction P
- Page 18 and 19: 5. DeviceNet 5.1 Introduction Devic
- Page 20 and 21: 5.2.6 Led indication Table 5 LED in
- Page 22 and 23: 6. RS-232 6.1 EmoSoftCom This conne
- Page 24 and 25: 7. Emotron MSF 2.0 NOTE: This chapt
- Page 26 and 27: 7.3 Installation in Emotron MSF-170
- Page 28 and 29: CG Drives & Automation 01-5927-01r0
- Page 30 and 31: Serial comm. unit address [270] 2 7
- Page 32 and 33: 2 7 3 Setting o F F Serial comm. co
- Page 34 and 35: 7.8 Map 7.8.1 Definitions This is t
- Page 36 and 37: 7.8.3 Response Bit Output from MSF
- Page 38 and 39: Bit Output from MSF Setting Comment
- Page 40: CG Drives & Automation Sweden AB M
1. Quick Set-up<br />
Following flowchart is a step by step guide for advanced users, with references to<br />
chapters with detailed information.<br />
Set FieldBus I/O Address<br />
- Profibus, see 4.2.3<br />
- DeviceNet, see 5.2.3<br />
Set FieldBus I/O Baudrate<br />
- Profibus, automatically selected<br />
- DeviceNet, see 5.2.4<br />
Set internal Communication Address<br />
- <strong>MSF</strong>, use address 1, see 7.4<br />
Set internal Communication Baudrate<br />
- <strong>MSF</strong>, use 19.2 kBaud, see 7.4<br />
Set Internal Communication Parity<br />
- <strong>MSF</strong>, use No Parity, see 7.4<br />
Set Control Mode<br />
- <strong>MSF</strong>, parameter 200, use mode 3,<br />
see 7.5<br />
Fig. 1<br />
Step by step guide.<br />
CG Drives & Automation 01-5927-01r0 Quick Set-up 3