Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
1 self-locking eccentric<br />
tension<br />
Type WB 100/E<br />
1<br />
1<br />
Radius Jaw No. 7 R=4 mm. With<br />
this jaw it is easy to bend and the<br />
risk of material fracture is reduced.<br />
This jaw and the sharp jaw are standard<br />
equipment.<br />
1<br />
Type WB 120/E<br />
- GOLIATH -<br />
1 Material tension with spindle and<br />
double prism guide<br />
2 Heavy bending arm, guided on a<br />
milled surface<br />
2 particularly narrow<br />
pressure-jaw<br />
3 strong bending arm<br />
with spindle<br />
6<br />
2<br />
Length-Stop 440 mm made of round<br />
steel with moveable stop made of<br />
investment cast is standard equipment.<br />
2<br />
5<br />
1<br />
2<br />
3<br />
3<br />
Allen Key to replace the jaws is<br />
standard equipment<br />
8<br />
7<br />
3<br />
2<br />
4<br />
Wide jaw No. 4 especially suitable<br />
for copper or aluminum rails as well<br />
for steel. This optional accessory is<br />
easy to replace.<br />
4<br />
5<br />
4<br />
5<br />
4<br />
5<br />
Wide jaw No. 5 for copper or aluminum<br />
rails is an optional accessory.<br />
Use only together with the wide jaw<br />
no. 4!<br />
6<br />
3<br />
Standard scope of delivery<br />
as shown<br />
4 bending lever lies below the<br />
bending plane<br />
5 pin-type angle stop with<br />
adjusting screw, 0-120°<br />
6 standard bend jaw No. 7,<br />
R=4 mm, made of hardened<br />
steel<br />
Bending Performance WB 100/E<br />
Values based on material cross sections at a strength of 40 da<br />
N / mm²<br />
Flat steel Max: 100 x 6 mm<br />
or Max: 50 x12 mm<br />
Round Steel Max: 18 mm<br />
Bends cold: Square Steel Max: 18 mm<br />
Flat Copper * Max: 100 x 12 mm<br />
<strong>Angle</strong> Steel *<br />
Notched Max: 60 x 8 mm<br />
6<br />
7<br />
8<br />
Wide jaw No. 6 with two radii, R=6<br />
mm and R= 12 mm, is an optional<br />
accessory.<br />
Radius Jaws No. 7 available with<br />
radii R= 4 mm up to R= 20 mm are<br />
optional accessory.<br />
Tie bending jaw No. 8 is an optional<br />
accessory for the close bending of<br />
grids or grating ties from 8 mm inside<br />
width upwards.<br />
7<br />
Standard scope of delivery<br />
as shown<br />
3 Milled plate with pin-type angle stop and<br />
adjusting screw for exact perpendicularity<br />
4 Double reinforced pressure vice<br />
5 Reversible jaw – one side Radius<br />
r= 10 mm, one side sharp<br />
7 Body and bending arm made<br />
of unbreakable ductile cast iron<br />
This information relates only for bends with the mounted radius jaw. The also included sharp<br />
jaw is only to bend sheet metal up to 2 mm. To bend stronger material sharp edged the wide<br />
jaw No. 5 is required.<br />
8 Length-Stop and sharp jaw<br />
No. 14 for sheet metal<br />
Flat steel Max: 100 x 12 mm<br />
or Max: 60 x 20 mm<br />
Biegt warm:<br />
Round Steel Max: 30 mm<br />
Square Steel Max: 30 mm<br />
<strong>Angle</strong> Steel *<br />
Notched Max: 100 x 12 mm<br />
*For these materials special jaws No. 4, No. 5 and No. 6 are necessary<br />
9<br />
Vee bar for the bending of square<br />
sections across the diagonal is an<br />
optional accessory.<br />
9<br />
8<br />
Optional Accessory<br />
Set of bending jaws 150 mm high<br />
Set of bending jaws 250 mm high<br />
2<br />
The stated description, measures and picture are only for information and may be changed