Angle Bender

Type WB 120/E
-GOLIATH-
An angle bender with excellent properties.
The generous use of cast iron meets the
highest requirements in terms of
precision or bending
performance.
KARNASCH Angle Benders made by Neu GmbH
The universal models for each locksmith forge and workshop with body
and bendingarm made of special ductile cast iron, not made of gray cast
iron! We obtain at low deadweight highest bending capacities. Close
Z-bends and U-bends are possible because of the small dimensions of
the jaws made of hardened steel. Therefore, it is also possible with these
standard jaws to bend hot work pieces.
For extremely heavy Edging with high bending accuracy our model
WB 120/E >Goliath< is available. This machine bends flat steel up to
120x10 mm and round steel up to 24 mm cold!
The descriptions and illustrations in this brochure have only informative character and are not binding.
We reserve the right to make any changes without notice that we deem useful!
Our Range of products
Bending Performance WB 120/E
Values based on material cross sections at a strength of 40 da N / mm²
Flat steel Max: 120 x 10 mm
Round Steel Max: 24 mm
Bends cold: Square Steel Max: 22 mm
Angle Steel * Max:
Notched
120 x 10 mm
Standard scope of delivery
Double reinforced pressure vice
Set of bending jaws 120 mm high
Lever
Pin-type angle stop and
adjusting screw
Length Stop
FREEFORMBENDERS
MANDRELBENDERS
DOUBLE HEAD MITER CUTTER FOR STEEL AND ALUMINUMPROFILES
PENDULUM SAW FOR TIMBER, PLASTIC AND LIGHT METALS
FLEXIBLE PUNCHING UNITS
FULLAUTOMATIC DRILLING AND MILLING APPARATUS
CNC-CONTROLLED POSITIONING SYSTEMS
ROLLERTABLES AND MEASURING STOPS
© 03/2015 by ES-DESIGN Stefan Ellbrück / www.designwelt.info
*For these materials special jaws No. 4, No. 5 and No. 6 are necessary
Technical Data
Model WB 100 E WB 120 E
Length / mm 260 540
Width / mm 290 380
Height / mm 280 280
Baseplate / mm 205 x 175 540 x 380
Weight / kg 24 90
Lever / mm 714 x 40 x 12 1200 Ø 48
Length Stop / mm 440 440
Pack size mm L/B/H 780 x 280 x 290 1200 x 800 x 500
Maschinenbau & Handel
Adam–Opel–Str. 4-6
D-67269 Grünstadt
Telefon: +49 (0)6359 87248-00
Telefax: +49 (0)6359 87248-99
Internet: www.neu-gmbh.de
eMail: info@neu-gmbh.de
Angle Bender
KARNASCH
Made in Germany

1 self-locking eccentric
tension
Type WB 100/E
1
1
Radius Jaw No. 7 R=4 mm. With
this jaw it is easy to bend and the
risk of material fracture is reduced.
This jaw and the sharp jaw are standard
equipment.
1
Type WB 120/E
- GOLIATH -
1 Material tension with spindle and
double prism guide
2 Heavy bending arm, guided on a
milled surface
2 particularly narrow
pressure-jaw
3 strong bending arm
with spindle
6
2
Length-Stop 440 mm made of round
steel with moveable stop made of
investment cast is standard equipment.
2
5
1
2
3
3
Allen Key to replace the jaws is
standard equipment
8
7
3
2
4
Wide jaw No. 4 especially suitable
for copper or aluminum rails as well
for steel. This optional accessory is
easy to replace.
4
5
4
5
4
5
Wide jaw No. 5 for copper or aluminum
rails is an optional accessory.
Use only together with the wide jaw
no. 4!
6
3
Standard scope of delivery
as shown
4 bending lever lies below the
bending plane
5 pin-type angle stop with
adjusting screw, 0-120°
6 standard bend jaw No. 7,
R=4 mm, made of hardened
steel
Bending Performance WB 100/E
Values based on material cross sections at a strength of 40 da
N / mm²
Flat steel Max: 100 x 6 mm
or Max: 50 x12 mm
Round Steel Max: 18 mm
Bends cold: Square Steel Max: 18 mm
Flat Copper * Max: 100 x 12 mm
Angle Steel *
Notched Max: 60 x 8 mm
6
7
8
Wide jaw No. 6 with two radii, R=6
mm and R= 12 mm, is an optional
accessory.
Radius Jaws No. 7 available with
radii R= 4 mm up to R= 20 mm are
optional accessory.
Tie bending jaw No. 8 is an optional
accessory for the close bending of
grids or grating ties from 8 mm inside
width upwards.
7
Standard scope of delivery
as shown
3 Milled plate with pin-type angle stop and
adjusting screw for exact perpendicularity
4 Double reinforced pressure vice
5 Reversible jaw – one side Radius
r= 10 mm, one side sharp
7 Body and bending arm made
of unbreakable ductile cast iron
This information relates only for bends with the mounted radius jaw. The also included sharp
jaw is only to bend sheet metal up to 2 mm. To bend stronger material sharp edged the wide
jaw No. 5 is required.
8 Length-Stop and sharp jaw
No. 14 for sheet metal
Flat steel Max: 100 x 12 mm
or Max: 60 x 20 mm
Biegt warm:
Round Steel Max: 30 mm
Square Steel Max: 30 mm
Angle Steel *
Notched Max: 100 x 12 mm
*For these materials special jaws No. 4, No. 5 and No. 6 are necessary
9
Vee bar for the bending of square
sections across the diagonal is an
optional accessory.
9
8
Optional Accessory
Set of bending jaws 150 mm high
Set of bending jaws 250 mm high
2
The stated description, measures and picture are only for information and may be changed