Operating manual 27.09.2011 CC Heating Thermostats - HUBER
Operating manual 27.09.2011 CC Heating Thermostats - HUBER Operating manual 27.09.2011 CC Heating Thermostats - HUBER
Decontamination / Repair The user is responsible for making sure that there are no hazardous materials either in or on the unit. The level of decontamination should be appropriate to the amount and type of contaminants on the unit. The user should refer to the appropriate MSDS information for advice. The decontamination should be done BEFORE outside personnel come into contact with the machine, and BEFORE the unit is sent out for repair or testing. The unit should be clearly labelled that it has been decontaminated before it is sent. We have prepared a document to simplify this process. This is available in the appendix, and at our website www.huber-online.com. Cleaning the surfaces A normal steel cleaning spray is suitable for cleaning the stainless steel surfaces. Painted areas should be carefully cleaned with a gentle detergent. Plug contacts Each socket has a protective cap belonging to it. If a connector is not required, then it should be covered with this cap. 88
Chapter 6: Taking the machine out of service The following sections can be found in this chapter: - Decommissioning - Transport - Disposal 89
- Page 37 and 38: Enter program A description on this
- Page 39 and 40: Warning time level As low-level pro
- Page 41 and 42: Time scale The time display can be
- Page 43 and 44: Analogue Interface AIF INPUT FUNCTI
- Page 45 and 46: Settings: 1. Settings on temperatur
- Page 47 and 48: POCO alarm Pot. free Contact (POCO)
- Page 49 and 50: Function Numbers and their meaning
- Page 51 and 52: F30 Set date Setting the date. F31
- Page 53 and 54: F90 Language / Sprache Selecting th
- Page 55 and 56: User menu - config. Using this main
- Page 57 and 58: Chapter 3: Connect the machine, fil
- Page 59 and 60: Counter cooling (valid for CC Heati
- Page 61 and 62: Switching on the temperature contro
- Page 63 and 64: Setting the safety value: Select th
- Page 65 and 66: Ending CC Temperature control The t
- Page 67 and 68: Draining the machine and an externa
- Page 69 and 70: Interface modules (RS232/SERIAL, Co
- Page 71 and 72: The following interfaces are availa
- Page 73 and 74: RS232 / RS485 Serial Socket A PC, P
- Page 75 and 76: Pin Designation 1 Level Test (Bridg
- Page 77 and 78: USB Device The operating mode of th
- Page 79 and 80: Firmware update: Updates and error
- Page 81 and 82: Messages Messages which occur can b
- Page 83 and 84: Alarm and Warning codes Hard Alarms
- Page 85 and 86: -143 -144 -148 -149 -150 -151 -152
- Page 87: Maintenance Danger! Prior to carrin
- Page 91 and 92: Transport The unit is now decommiss
Decontamination / Repair<br />
The user is responsible for making sure that there are no hazardous materials either in<br />
or on the unit. The level of decontamination should be appropriate to the amount and<br />
type of contaminants on the unit. The user should refer to the appropriate MSDS<br />
information for advice.<br />
The decontamination should be done BEFORE outside personnel come into contact with<br />
the machine, and BEFORE the unit is sent out for repair or testing. The unit should be<br />
clearly labelled that it has been decontaminated before it is sent.<br />
We have prepared a document to simplify this process. This is available in the appendix,<br />
and at our website www.huber-online.com.<br />
Cleaning the surfaces<br />
A normal steel cleaning spray is suitable for cleaning the stainless steel surfaces.<br />
Painted areas should be carefully cleaned with a gentle detergent.<br />
Plug contacts<br />
Each socket has a protective cap belonging to it. If a connector is not required, then it<br />
should be covered with this cap.<br />
88
Change language