Operating manual 27.09.2011 CC Heating Thermostats - HUBER

More documents

Recommendations

Info

Mutual functions Com.G@te/Web.G@te PoKo (potential free contact) Alarm plug connector Signal contact for external monitoring Observe the functional options, which the PoKo provides in the main menu. The potential free contact (PoKo) signals the condition of the temperature control device by means of the contact position. A closed operating contact means ready status (must be set via the menu). The operating contact is open in case of a fault or error (this applies to the normally open contact between pin 1 and pin 2). Further applications are possible e.g checking of the actual value. The connection is designed as a potential free changeover contact. 72 1 3 2 ECS Socket (External Control Signal) Standby Release signal ECS (External Control Signal), for starting / stopping temperature control. The ECS can be used to switch of the temperature control mode (internal/process), switch to the 2 nd set-point or allow temperature control. Control over a potential free contact. The contacts 1 and 3 are bridged internally. ECS becomes electronically active, if E1 and E2 are connected by an external zero potential free contact. The functionality of the ECS is determined in the Com.G@te / Web.G@te menu under the point ECS Standby. The following options are offered: - OFF: ECS does not have any effect (Factory default) - 2 nd set-point: The 2 nd set-point is taken over as soon as ECS is activated - Standby: ECS has effect on temperature control (ON / OFF) 3 2 1 Normally open contact between pin 1 and pin 2. Normally closed contact between pin 2 and pin 3. Contact load: 1A at 24V DC Pin Signal 1,3 E2 2 E1
RS232 / RS485 Serial Socket A PC, PLC or a process control system (PCS) can be connected to this socket, in order to remotely control the controller. Alternatively, connecting to a RS485 bus is also possible (not valid for the Web.G@te). Before connecting the line, check and if necessary adjust the settings in the menu Digit. Interface. Wiring RS232: Pin2 RxD Receive Data Pin3 TxD Transmit Data Pin5 GND Signal GND Wiring RS485: Pin6 A with120 Ohm load resistance. Pin7 A Pin8 B 73
Page 1 and 2:
Valid for: Operating manual CC 27.0
Page 3 and 4:
Filling and air purging an external
Page 5 and 6:
Quick guide for CC-thermostats Chec
Page 7 and 8:
Chapter 1: Safety In this chapter i
Page 9 and 10:
Intended Use and General Safety Ins
Page 11 and 12:
Duties of responsible person The op
Page 13 and 14:
To 1. Temperature control machines
Page 15 and 16:
Operating conditions Please make su
Page 17 and 18:
Chapter 2: Electronics and operatio
Page 19 and 20:
Information Displays CC The followi
Page 21 and 22: Field 10: Display delta T This fiel
Page 23 and 24: Operation CC Please note, there are
Page 25 and 26: CC Operation using the simulated Nu
Page 27 and 28: Compact menu Control parameters: Th
Page 29 and 30: 2. With preliminary Test: To achiev
Page 31 and 32: Example: Indication when choosing L
Page 33 and 34: To create a new program, continue a
Page 35 and 36: Comfort menu Acoustic alarm Here yo
Page 37 and 38: Enter program A description on this
Page 39 and 40: Warning time level As low-level pro
Page 41 and 42: Time scale The time display can be
Page 43 and 44: Analogue Interface AIF INPUT FUNCTI
Page 45 and 46: Settings: 1. Settings on temperatur
Page 47 and 48: POCO alarm Pot. free Contact (POCO)
Page 49 and 50: Function Numbers and their meaning
Page 51 and 52: F30 Set date Setting the date. F31
Page 53 and 54: F90 Language / Sprache Selecting th
Page 55 and 56: User menu - config. Using this main
Page 57 and 58: Chapter 3: Connect the machine, fil
Page 59 and 60: Counter cooling (valid for CC Heati
Page 61 and 62: Switching on the temperature contro
Page 63 and 64: Setting the safety value: Select th
Page 65 and 66: Ending CC Temperature control The t
Page 67 and 68: Draining the machine and an externa
Page 69 and 70: Interface modules (RS232/SERIAL, Co
Page 71: The following interfaces are availa
Page 75 and 76: Pin Designation 1 Level Test (Bridg
Page 77 and 78: USB Device The operating mode of th
Page 79 and 80: Firmware update: Updates and error
Page 81 and 82: Messages Messages which occur can b
Page 83 and 84: Alarm and Warning codes Hard Alarms
Page 85 and 86: -143 -144 -148 -149 -150 -151 -152
Page 87 and 88: Maintenance Danger! Prior to carrin
Page 89 and 90: Chapter 6: Taking the machine out o
Page 91 and 92: Transport The unit is now decommiss
show all

Operating manual 27.09.2011 CC Heating Thermostats - HUBER

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?