Operating manual 27.09.2011 CC Heating Thermostats - HUBER

More documents

Recommendations

Info

COM.G@TE allocation and setting (quick guide) 6 1 2 3 5 4 6 3 2 1 3 2 1 5 1 9 6 POCO (potential free contact) Alarm plug-in connector Signal contact for external monitoring. The connection is designed as a potential free changeover contact. Normally open contact between pin 1 and pin 2. Normally closed contact between pin 2 and pin 3. Contact load: 1A at 24V DC Only use screened lines! AIF Reg-E-Prog Socket Analogue interface, one input channel (programmable) and 3 output channels. Pin Signal 1. Current output, T extern 0/4-20mA or 0-10V 2. Current output, set-point 0/4-20mA or 0-10V 3. GND for analogue outputs GND 4. Analogue input (programmable) 0/4-20mA or 0-10V 5. Current output, free programmable 0/4-20mA or 0-10V 6. GND for analogue input GND ECS Socket (External Control Signal) Standby Release signal ECS (External Control Signal), for starting / stopping temperature control. The following variants are offered: Pin Signal 1,3 E2 2 E1 RS232 / RS485 Serial Socket Wiring RS232: Wiring RS485 Pin2 RxD Receive Data Pin6 A with 120 Ohm load resistance Pin3 TxD Transmit Data Pin7 A Pin5 GND Signal GND Pin8 B Functions in connection with PLS Settings for analogue interface, release signal, signal contact and digital interface RS232 / RS485 can be made via the functions Analogue Interface, RS232 / RS485, ECS Standby and POCO Alarm in the COM.G@TE menu. Standard settings are: Analogue interface: analogue input OFF and analogue output OFF RS232 / RS485: RS232 with Baudrate 9600 ECS Standby: no action POCO Alarm: no alarm Here you can determine a temperature / current range and predefine the current input value as set-point or speed of rotation! Here you can determine whether the temperature control unit is switched OFF/ON via an external switch contact! COM.G@TE: Analogue-Interface RS232/RS485 ECS Standby POCO Alarm Return to main m... Here you can determine e.g. the dig. Interface, as well as baudrate and slave address with RS485! Here you can determine whether the unit reports a contact condition in case of a disturbance (alarm).
Chapter 1: Safety In this chapter is to be found the following sections: - Description of safety and information symbols - Intended use and General Safety Information - Description - Duties of the responsible person - Operator requirements - Machine operator duties - Work area - Safety Devices to DIN 12876 (applicable for units with heating) - Additional Protection Devices (if provided) - Environmental conditions - <strong>Operating</strong> conditions - Location - Thermal fluids 7
Page 1 and 2: Valid for: Operating manual CC 27.0
Page 3 and 4: Filling and air purging an external
Page 5: Quick guide for CC-thermostats Chec
Page 9 and 10: Intended Use and General Safety Ins
Page 11 and 12: Duties of responsible person The op
Page 13 and 14: To 1. Temperature control machines
Page 15 and 16: Operating conditions Please make su
Page 17 and 18: Chapter 2: Electronics and operatio
Page 19 and 20: Information Displays CC The followi
Page 21 and 22: Field 10: Display delta T This fiel
Page 23 and 24: Operation CC Please note, there are
Page 25 and 26: CC Operation using the simulated Nu
Page 27 and 28: Compact menu Control parameters: Th
Page 29 and 30: 2. With preliminary Test: To achiev
Page 31 and 32: Example: Indication when choosing L
Page 33 and 34: To create a new program, continue a
Page 35 and 36: Comfort menu Acoustic alarm Here yo
Page 37 and 38: Enter program A description on this
Page 39 and 40: Warning time level As low-level pro
Page 41 and 42: Time scale The time display can be
Page 43 and 44: Analogue Interface AIF INPUT FUNCTI
Page 45 and 46: Settings: 1. Settings on temperatur
Page 47 and 48: POCO alarm Pot. free Contact (POCO)
Page 49 and 50: Function Numbers and their meaning
Page 51 and 52: F30 Set date Setting the date. F31
Page 53 and 54: F90 Language / Sprache Selecting th
Page 55 and 56: User menu - config. Using this main
Page 57 and 58:
Chapter 3: Connect the machine, fil
Page 59 and 60:
Counter cooling (valid for CC Heati
Page 61 and 62:
Switching on the temperature contro
Page 63 and 64:
Setting the safety value: Select th
Page 65 and 66:
Ending CC Temperature control The t
Page 67 and 68:
Draining the machine and an externa
Page 69 and 70:
Interface modules (RS232/SERIAL, Co
Page 71 and 72:
The following interfaces are availa
Page 73 and 74:
RS232 / RS485 Serial Socket A PC, P
Page 75 and 76:
Pin Designation 1 Level Test (Bridg
Page 77 and 78:
USB Device The operating mode of th
Page 79 and 80:
Firmware update: Updates and error
Page 81 and 82:
Messages Messages which occur can b
Page 83 and 84:
Alarm and Warning codes Hard Alarms
Page 85 and 86:
-143 -144 -148 -149 -150 -151 -152
Page 87 and 88:
Maintenance Danger! Prior to carrin
Page 89 and 90:
Chapter 6: Taking the machine out o
Page 91 and 92:
Transport The unit is now decommiss
show all

Operating manual 27.09.2011 CC Heating Thermostats - HUBER

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?