Operating manual 27.09.2011 CC Heating Thermostats - HUBER
Operating manual 27.09.2011 CC Heating Thermostats - HUBER Operating manual 27.09.2011 CC Heating Thermostats - HUBER
Over-temperature protection 62 Protection overtemperature Actual OT values Sensor heater 1 19.0°C Tripping points Setting OT ht.1 35.0°C OT Mode Stop Continue: Press Encoder CONTROL OF PROTECTION: Stop Process security Go back Stop: cutoff of heating, pump and refrigeration machine Process security: refrigeration machine continues. CHARACTERISTICS: OT limit: heating OT Mode Display all OT values Return to main menu Please enter code Actual setting: 0000 Max. setting 65535 CHARACTERISTICS: OT limit: heating OT Mode Display all OT values Return to main menu Code for OT input OT Mode OT limit: heating Min. setting 0000 New value xxxx ESC OK KEYB OT Set-point Circulation Actual setting: 35.00 Temp. max. 200.00 Act. temp. 22.40 Temp. min -40.00 New setting xxxx ESC OK KEYB 77 Notice: Please consider the statutory and internal regulatons when setting the OT limit. OK OK
Setting the safety value: Select the Over-temperature protection from the main menu. Choose the menu point OT limits: heating. A code generator (random generator) will give out a code via the graphics display. This code has to be entered when requested (a deliberate and knowing action). This procedure replaces the usual setting by means of a tool (screw driver). Afterwards the new safety value can be entered. Setting the OT Mode: Information! Standard setting is Stop to DIN EN 61010. Please note that after a default setting the over-temperature protection will be set to Stop according to DIN EN 61010! Select the Over-temperature protection from the main menu. Choose the menu point OT mode. A code generator (random generator) will give out a code via the graphics display. This code has to be entered when requested (a deliberate and knowing action). This procedure replaces the usual setting by means of a tool (screw driver). Afterwards the new safety value can be entered. Stop according to DIN EN 61010 When the cut-off temperature is reached, heating, cooling and pump are all turned off (Default setting). Cut-off mode: Process Safety When the cut-off temperature is reached the heating is turned off, but the cooling (at maximum power) and pump remain on. The full cooling capacity of the unit remains available for emergency cooling (possible exothermic reaction). Please ensure that the compressor automatic is switched to always on using the menu point Compressor automatic (F35). Please also see description on chapter Comfort menu for the respective Function numbers and their meanings. Display all OT values: The present measured temperature of the over-temperature sensors, the trip temperature set and the cut-off mode are displayed. Please note, that some units use two over-temperature sensors. When selecting Display all OT values both values will be displayed. 63
- Page 11 and 12: Duties of responsible person The op
- Page 13 and 14: To 1. Temperature control machines
- Page 15 and 16: Operating conditions Please make su
- Page 17 and 18: Chapter 2: Electronics and operatio
- Page 19 and 20: Information Displays CC The followi
- Page 21 and 22: Field 10: Display delta T This fiel
- Page 23 and 24: Operation CC Please note, there are
- Page 25 and 26: CC Operation using the simulated Nu
- Page 27 and 28: Compact menu Control parameters: Th
- Page 29 and 30: 2. With preliminary Test: To achiev
- Page 31 and 32: Example: Indication when choosing L
- Page 33 and 34: To create a new program, continue a
- Page 35 and 36: Comfort menu Acoustic alarm Here yo
- Page 37 and 38: Enter program A description on this
- Page 39 and 40: Warning time level As low-level pro
- Page 41 and 42: Time scale The time display can be
- Page 43 and 44: Analogue Interface AIF INPUT FUNCTI
- Page 45 and 46: Settings: 1. Settings on temperatur
- Page 47 and 48: POCO alarm Pot. free Contact (POCO)
- Page 49 and 50: Function Numbers and their meaning
- Page 51 and 52: F30 Set date Setting the date. F31
- Page 53 and 54: F90 Language / Sprache Selecting th
- Page 55 and 56: User menu - config. Using this main
- Page 57 and 58: Chapter 3: Connect the machine, fil
- Page 59 and 60: Counter cooling (valid for CC Heati
- Page 61: Switching on the temperature contro
- Page 65 and 66: Ending CC Temperature control The t
- Page 67 and 68: Draining the machine and an externa
- Page 69 and 70: Interface modules (RS232/SERIAL, Co
- Page 71 and 72: The following interfaces are availa
- Page 73 and 74: RS232 / RS485 Serial Socket A PC, P
- Page 75 and 76: Pin Designation 1 Level Test (Bridg
- Page 77 and 78: USB Device The operating mode of th
- Page 79 and 80: Firmware update: Updates and error
- Page 81 and 82: Messages Messages which occur can b
- Page 83 and 84: Alarm and Warning codes Hard Alarms
- Page 85 and 86: -143 -144 -148 -149 -150 -151 -152
- Page 87 and 88: Maintenance Danger! Prior to carrin
- Page 89 and 90: Chapter 6: Taking the machine out o
- Page 91 and 92: Transport The unit is now decommiss
Over-temperature protection<br />
62<br />
Protection overtemperature<br />
Actual OT values<br />
Sensor heater 1 19.0°C<br />
Tripping points<br />
Setting OT ht.1 35.0°C<br />
OT Mode Stop<br />
Continue: Press Encoder<br />
CONTROL OF PROTECTION:<br />
Stop<br />
Process security<br />
Go back<br />
Stop: cutoff of heating, pump<br />
and refrigeration machine<br />
Process security:<br />
refrigeration machine continues.<br />
CHARACTERISTICS:<br />
OT limit: heating<br />
OT Mode<br />
Display all OT values<br />
Return to main menu<br />
Please enter code<br />
Actual setting: 0000<br />
Max. setting 65535<br />
CHARACTERISTICS:<br />
OT limit: heating<br />
OT Mode<br />
Display all OT values<br />
Return to main menu<br />
Code for OT input<br />
OT Mode OT limit: heating<br />
Min. setting 0000<br />
New value xxxx<br />
ESC OK KEYB<br />
OT Set-point Circulation<br />
Actual setting: 35.00<br />
Temp. max. 200.00<br />
Act. temp. 22.40<br />
Temp. min -40.00<br />
New setting xxxx<br />
ESC OK KEYB<br />
77<br />
Notice:<br />
Please consider the statutory and<br />
internal regulatons when setting<br />
the OT limit.<br />
OK<br />
OK