Operating manual 27.09.2011 CC Heating Thermostats - HUBER
Operating manual 27.09.2011 CC Heating Thermostats - HUBER Operating manual 27.09.2011 CC Heating Thermostats - HUBER
Com.G@te menu Here, the functions (analogue interface, RS232/RS485, ECS-Standby, POCO Alarm) used in connection with an external control (e.g process control system “PCS”) are listed. 42 ANALOGUE-INTERFACE: Config. input Config. output Go back USE EXTERNAL SIGNAL TO: No action Switch to 2nd setp. 2nd set-point selectiv Internal / Process Temp. contr. on/off Enable machine Go back COM.G@TE: Analogue interface RS232/RS485 ECS Standby POCO Alarm Return to main menu POCO ACTION: OFF Check act. value External Alarm Unipump/PCS Control by RS232 Check process temp. Unipump with echo Programmerr Check int. temp. abs. Check proc. temp. abs. Go back DIGITAL INTERFACE: Select RS232/485 Baud rate Slave address (LAI) Go back
Analogue Interface AIF INPUT FUNCTION: AIF ->Input off AIF ->Internal temp. AIF ->Process Temp. AIF ->Set-point AIF ->Heating 0-100% AIF ->Power AIF ->Pump speed setp. AIF ->Pump press. setp. Go back ADJUST: Adj. current value Enter in table Go back Adjustment of the current measured value by input of the reference value ANALOGUE INPUT: Means: AIF -> Input off Action on analogue error: Switch off Action on cable break: Trigger an alarm Configuration In/Out 4.00mA -> 274.0 °C 20.00mA -> 274.0 °C Actual AIF input values: 0 Bit -> 0.00mA->0.00 °C Continue: Press Encoder button ANALOGUE-INTERFACE: Config. input Config. output Go back ANALOGUE INPUT: AIF–Input - Function On cable break Cfg. input range Adjustment On analogue error Display AIF value Reset AIF input Show table values Current / voltage switch Filter constant Go back SHOW TABLE VALUES: ref. val meas. val P1 10485 10485 P2 52428 52428 WARNING: Following Parameters are going to be removed when resetting the analogue interface Measurement range Adjustment In / output function AIF FILTER CONST: Act. Setting: 0002 Max. Setting 0010 Min. Setting 0000 New setting 0002 CURRENT / VOLTAGE SWITCH: Current Voltage Go back ON CABLE BREAK: Trigger an alarm No alarm, normal operation Go back Temperature T1 Actual setting: -40,00 Max. setting 350,00 Min. setting -150.00 New value: : -40,0 OK ESC OK KEYB Temperature T2 Actual setting -40,00 Max. setting 350,00 Min. setting -150.00 New value: -40,0 ESC OK KEYB ON ANALOGUE ERROR: Switch off Act. 2 nd Set-point Go back 43
- Page 1 and 2: Valid for: Operating manual CC 27.0
- Page 3 and 4: Filling and air purging an external
- Page 5 and 6: Quick guide for CC-thermostats Chec
- Page 7 and 8: Chapter 1: Safety In this chapter i
- Page 9 and 10: Intended Use and General Safety Ins
- Page 11 and 12: Duties of responsible person The op
- Page 13 and 14: To 1. Temperature control machines
- Page 15 and 16: Operating conditions Please make su
- Page 17 and 18: Chapter 2: Electronics and operatio
- Page 19 and 20: Information Displays CC The followi
- Page 21 and 22: Field 10: Display delta T This fiel
- Page 23 and 24: Operation CC Please note, there are
- Page 25 and 26: CC Operation using the simulated Nu
- Page 27 and 28: Compact menu Control parameters: Th
- Page 29 and 30: 2. With preliminary Test: To achiev
- Page 31 and 32: Example: Indication when choosing L
- Page 33 and 34: To create a new program, continue a
- Page 35 and 36: Comfort menu Acoustic alarm Here yo
- Page 37 and 38: Enter program A description on this
- Page 39 and 40: Warning time level As low-level pro
- Page 41: Time scale The time display can be
- Page 45 and 46: Settings: 1. Settings on temperatur
- Page 47 and 48: POCO alarm Pot. free Contact (POCO)
- Page 49 and 50: Function Numbers and their meaning
- Page 51 and 52: F30 Set date Setting the date. F31
- Page 53 and 54: F90 Language / Sprache Selecting th
- Page 55 and 56: User menu - config. Using this main
- Page 57 and 58: Chapter 3: Connect the machine, fil
- Page 59 and 60: Counter cooling (valid for CC Heati
- Page 61 and 62: Switching on the temperature contro
- Page 63 and 64: Setting the safety value: Select th
- Page 65 and 66: Ending CC Temperature control The t
- Page 67 and 68: Draining the machine and an externa
- Page 69 and 70: Interface modules (RS232/SERIAL, Co
- Page 71 and 72: The following interfaces are availa
- Page 73 and 74: RS232 / RS485 Serial Socket A PC, P
- Page 75 and 76: Pin Designation 1 Level Test (Bridg
- Page 77 and 78: USB Device The operating mode of th
- Page 79 and 80: Firmware update: Updates and error
- Page 81 and 82: Messages Messages which occur can b
- Page 83 and 84: Alarm and Warning codes Hard Alarms
- Page 85 and 86: -143 -144 -148 -149 -150 -151 -152
- Page 87 and 88: Maintenance Danger! Prior to carrin
- Page 89 and 90: Chapter 6: Taking the machine out o
- Page 91 and 92: Transport The unit is now decommiss
Com.G@te menu<br />
Here, the functions (analogue interface, RS232/RS485, ECS-Standby, POCO Alarm)<br />
used in connection with an external control (e.g process control system “PCS”) are<br />
listed.<br />
42<br />
ANALOGUE-INTERFACE:<br />
Config. input<br />
Config. output<br />
Go back<br />
USE EXTERNAL SIGNAL TO:<br />
No action<br />
Switch to 2nd setp.<br />
2nd set-point selectiv<br />
Internal / Process<br />
Temp. contr. on/off<br />
Enable machine<br />
Go back<br />
COM.G@TE:<br />
Analogue interface<br />
RS232/RS485<br />
ECS Standby<br />
POCO Alarm<br />
Return to main menu<br />
POCO ACTION:<br />
OFF<br />
Check act. value<br />
External Alarm<br />
Unipump/PCS<br />
Control by RS232<br />
Check process temp.<br />
Unipump with echo<br />
Programmerr<br />
Check int. temp. abs.<br />
Check proc. temp. abs.<br />
Go back<br />
DIGITAL INTERFACE:<br />
Select RS232/485<br />
Baud rate<br />
Slave address (LAI)<br />
Go back