Operating manual 27.09.2011 CC Heating Thermostats - HUBER
Operating manual 27.09.2011 CC Heating Thermostats - HUBER Operating manual 27.09.2011 CC Heating Thermostats - HUBER
Set-point A description on this menu point can be found in the chapter on the Compact menu. Set-point limits A description on this menu point can be found in the chapter on Compact menu. Settings (others) Here, information concerning your application may be entered or read out. The values input here will be considered when controller parameterisation is taking place (please see chapter on Control parameters) The following functions are available under the menu point Change thermal fluid: 40 1. Thermal fluid (choose thermal fluid) 2. Circulation volume (indication on volume to be temperature controlled) 3. Bypass usage 4. Show fluid (values and information on thermal fluid are being displayed) 5. Back Under the menu point Bath selection different bath volumes can be chosen. Please select accordingly. Software version Corresponds to Function F98 in the Function-no. menu. The installed software version of the electronics are displayed. petite fleur Serial Number: 77507 LoadCode: 803261629 Create Conde : 708020946 CC-Pilot: V06.10.001 Jan 12 2010 16:38:15 Serial Number : 36 Control: V05.10.001 1201 Jan 12 2010 16:38:15 Serial Number : 747 Continue: Press Enconder button Start & stop A description on this menu point can be found in the chapter on Compact menu. Start ramp A description on this point can be found in the chapter on Compact menu. Temperature control mode A description on this menu point can be found in the chapter on Compact menu. Temperature scale It is possible to choose between °C, °F and K
Time scale The time display can be displayed in various formats (hh, min, sec). 2 nd set-point Corresponds to the Function F4 in the Function-no. menu. The input of a 2 nd or alternative set-point is done in the same way as the normal set-point under the menu point set-point. This second set-point is activated with an external control signal (Function F28) or through a watchdog event User menu - select A description on this menu point can be found in the chapter on Compact menu. User menu - config. A description on this menu point can be found in the chapter on Compact menu. 41
- Page 1 and 2: Valid for: Operating manual CC 27.0
- Page 3 and 4: Filling and air purging an external
- Page 5 and 6: Quick guide for CC-thermostats Chec
- Page 7 and 8: Chapter 1: Safety In this chapter i
- Page 9 and 10: Intended Use and General Safety Ins
- Page 11 and 12: Duties of responsible person The op
- Page 13 and 14: To 1. Temperature control machines
- Page 15 and 16: Operating conditions Please make su
- Page 17 and 18: Chapter 2: Electronics and operatio
- Page 19 and 20: Information Displays CC The followi
- Page 21 and 22: Field 10: Display delta T This fiel
- Page 23 and 24: Operation CC Please note, there are
- Page 25 and 26: CC Operation using the simulated Nu
- Page 27 and 28: Compact menu Control parameters: Th
- Page 29 and 30: 2. With preliminary Test: To achiev
- Page 31 and 32: Example: Indication when choosing L
- Page 33 and 34: To create a new program, continue a
- Page 35 and 36: Comfort menu Acoustic alarm Here yo
- Page 37 and 38: Enter program A description on this
- Page 39: Warning time level As low-level pro
- Page 43 and 44: Analogue Interface AIF INPUT FUNCTI
- Page 45 and 46: Settings: 1. Settings on temperatur
- Page 47 and 48: POCO alarm Pot. free Contact (POCO)
- Page 49 and 50: Function Numbers and their meaning
- Page 51 and 52: F30 Set date Setting the date. F31
- Page 53 and 54: F90 Language / Sprache Selecting th
- Page 55 and 56: User menu - config. Using this main
- Page 57 and 58: Chapter 3: Connect the machine, fil
- Page 59 and 60: Counter cooling (valid for CC Heati
- Page 61 and 62: Switching on the temperature contro
- Page 63 and 64: Setting the safety value: Select th
- Page 65 and 66: Ending CC Temperature control The t
- Page 67 and 68: Draining the machine and an externa
- Page 69 and 70: Interface modules (RS232/SERIAL, Co
- Page 71 and 72: The following interfaces are availa
- Page 73 and 74: RS232 / RS485 Serial Socket A PC, P
- Page 75 and 76: Pin Designation 1 Level Test (Bridg
- Page 77 and 78: USB Device The operating mode of th
- Page 79 and 80: Firmware update: Updates and error
- Page 81 and 82: Messages Messages which occur can b
- Page 83 and 84: Alarm and Warning codes Hard Alarms
- Page 85 and 86: -143 -144 -148 -149 -150 -151 -152
- Page 87 and 88: Maintenance Danger! Prior to carrin
- Page 89 and 90: Chapter 6: Taking the machine out o
Set-point<br />
A description on this menu point can be found in the chapter on the Compact menu.<br />
Set-point limits<br />
A description on this menu point can be found in the chapter on Compact menu.<br />
Settings (others)<br />
Here, information concerning your application may be entered or read out. The values<br />
input here will be considered when controller parameterisation is taking place (please<br />
see chapter on Control parameters)<br />
The following functions are available under the menu point Change thermal fluid:<br />
40<br />
1. Thermal fluid (choose thermal fluid)<br />
2. Circulation volume (indication on volume to be temperature controlled)<br />
3. Bypass usage<br />
4. Show fluid (values and information on thermal fluid are being displayed)<br />
5. Back<br />
Under the menu point Bath selection different bath volumes can be chosen. Please<br />
select accordingly.<br />
Software version<br />
Corresponds to Function F98 in the Function-no. menu.<br />
The installed software version of the electronics are displayed.<br />
petite fleur<br />
Serial Number: 77507<br />
LoadCode: 803261629<br />
Create Conde : 708020946<br />
<strong>CC</strong>-Pilot: V06.10.001<br />
Jan 12 2010 16:38:15<br />
Serial Number : 36<br />
Control: V05.10.001 1201<br />
Jan 12 2010 16:38:15<br />
Serial Number : 747<br />
Continue: Press Enconder<br />
button<br />
Start & stop<br />
A description on this menu point can be found in the chapter on Compact menu.<br />
Start ramp<br />
A description on this point can be found in the chapter on Compact menu.<br />
Temperature control mode<br />
A description on this menu point can be found in the chapter on Compact menu.<br />
Temperature scale<br />
It is possible to choose between °C, °F and K