Operating manual 27.09.2011 CC Heating Thermostats - HUBER

More documents

Recommendations

Info

Foreword Dear Customer, The Huber team would like to thank you for ordering this product. You have made a good choice. We thank you for your trust! Please read and understand the instruction manual thoroughly before operating the unit. All instructions and safety information must be complied with. Please read this manual before transporting, commissioning, operating, maintaining, repairing, storing or disposing of this unit. Failure to comply with the instructions within this manual may invalidate any warranty for this unit. 4
Quick guide for CC-thermostats Checklist for initial operation: 1. Make sure that the machine is connected correctly and enough thermal fluid is inside. 2. Switch on the unit via the mains switch! 3. Make sure that the over-temperature is set correctly. 4. Make sure that the set-point limits (min and max) are set correctly. 5. Enter e.g. a new set-point! 6. Make sure that you have set the correct temperature control mode (e.g.process)! 7. Start temperature control! Operation: T-set button Press this button to enter a new setpoint. Compact menu: Display modes � Here you can select the graphic display. Comfort menu � Here one can have displayed the whole menu function. Program edit � Here you can edit a temperature program. Program start & stop � Here you can start / stop a temperature program. Pump settings � Here you can predefine a pump speed. Start ramp� Here you can predefine a temperature ramp. Control parameters � Here you can select/predefine control parameters. Set-point � Here you can predefine a set-point. Set-point limits � Here you can set set-point limits. Start&Stop � Here you can start / stop temperature control. Temperature control mode � Here you can select between jacket / process control Over-temp. Protection � Here you can set the over-temperature protection. Select user menu � Here you can select an individual menu. Exit � Button for main menu and menu selection. By pressing the rotary knob / encoder you can reach the compact menu with above mentioned functions. ESCAPE-Button To cancel a process (entry), press the ESC button. START / STOP-Button Here you can start / stop circulation, air-purge and thermoregulation. Setting the over-temperature protection: 1. Select the function over-temperature from the compact menu! 2. Select the menu point, setting the over-temperature protection! 3. To adjust the over-temperature a code is being given out via the display for several seconds. 4. You are being requested to enter a code! 5. Enter the code which has been displayed previously! 6. The over-temperature can be adjusted if the code has been entered correctly! 7. The new over-temperature value will be now displayed! 5
Page 1 and 2: Valid for: Operating manual CC 27.0
Page 3: Filling and air purging an external
Page 7 and 8: Chapter 1: Safety In this chapter i
Page 9 and 10: Intended Use and General Safety Ins
Page 11 and 12: Duties of responsible person The op
Page 13 and 14: To 1. Temperature control machines
Page 15 and 16: Operating conditions Please make su
Page 17 and 18: Chapter 2: Electronics and operatio
Page 19 and 20: Information Displays CC The followi
Page 21 and 22: Field 10: Display delta T This fiel
Page 23 and 24: Operation CC Please note, there are
Page 25 and 26: CC Operation using the simulated Nu
Page 27 and 28: Compact menu Control parameters: Th
Page 29 and 30: 2. With preliminary Test: To achiev
Page 31 and 32: Example: Indication when choosing L
Page 33 and 34: To create a new program, continue a
Page 35 and 36: Comfort menu Acoustic alarm Here yo
Page 37 and 38: Enter program A description on this
Page 39 and 40: Warning time level As low-level pro
Page 41 and 42: Time scale The time display can be
Page 43 and 44: Analogue Interface AIF INPUT FUNCTI
Page 45 and 46: Settings: 1. Settings on temperatur
Page 47 and 48: POCO alarm Pot. free Contact (POCO)
Page 49 and 50: Function Numbers and their meaning
Page 51 and 52: F30 Set date Setting the date. F31
Page 53 and 54: F90 Language / Sprache Selecting th
Page 55 and 56:
User menu - config. Using this main
Page 57 and 58:
Chapter 3: Connect the machine, fil
Page 59 and 60:
Counter cooling (valid for CC Heati
Page 61 and 62:
Switching on the temperature contro
Page 63 and 64:
Setting the safety value: Select th
Page 65 and 66:
Ending CC Temperature control The t
Page 67 and 68:
Draining the machine and an externa
Page 69 and 70:
Interface modules (RS232/SERIAL, Co
Page 71 and 72:
The following interfaces are availa
Page 73 and 74:
RS232 / RS485 Serial Socket A PC, P
Page 75 and 76:
Pin Designation 1 Level Test (Bridg
Page 77 and 78:
USB Device The operating mode of th
Page 79 and 80:
Firmware update: Updates and error
Page 81 and 82:
Messages Messages which occur can b
Page 83 and 84:
Alarm and Warning codes Hard Alarms
Page 85 and 86:
-143 -144 -148 -149 -150 -151 -152
Page 87 and 88:
Maintenance Danger! Prior to carrin
Page 89 and 90:
Chapter 6: Taking the machine out o
Page 91 and 92:
Transport The unit is now decommiss
show all

Operating manual 27.09.2011 CC Heating Thermostats - HUBER

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?