MACH 130 FP Mains Voltage 230V / 120V - Dr. Mach

More documents

Recommendations

Info

MACH 130 FP Wall model GL 45 58 44 45 4.2 Positioning Dr. Mach Lamps and Engineering Use the handle or the handle rail GL to position the lamp. The lamp is equipped with a handle with sterilizable handle sleeve 45. The sterilizable handle sleeve 45 can be removed. It is fixed by the couple 44 to the handle bar 58. 4.3 Light field adjustment (focusing) – Mach 130 FP The lamp models Mach 130 FP have a focusing function. That means, you can either enlarge the diameter of the light field or bundle the light to a smaller area, depending on the circumstances. To activate the function of focusing turn the handle 45 (see figure). 59100002 Edition 07 05.06.2002 / Bak Page 8/25
MACH 130 FP Wall model V 45 Cleaning / disinfection and sterilisation 5. Cleaning 5.1 Sterilizable handle Dr. Mach Lamps and Engineering The lamps Mach 130/Mach 130F 22,8V UL/Uniflex R96 120V UL can be equipped as an option with a sterilizable handle 45. The sterilizable handle 45 is removable and sterilizable. Before using the first time and before every use the handle sleeve must be cleaned, disinfected and sterilised. The handle sleeve must be removed for sterilisation: • To remove press the lock V and pull off the sterilisable handle sleeve 45 while keeping the lock pressed. • To attach, push on and slightly twist the handle until the lock V engages securely. Handles often become unsterile during an OP; therefore always keep additional handles available for exchange. Basics Efficient cleaning / disinfection is an essential requirement for effective sterilisation of the handle. Within the scope of responsibility for the sterility of the products it should be noted that only sufficiently validated equipment and product specific processes are used for cleaning / disinfection and that the validated parameters are complied with in every cycle. In addition, the hospital / clinic hygiene regulations must be observed. Cleaning / disinfection Cleaning and disinfection must be carried out immediately after use. A mechanised process (disinfector) should be used for cleaning / disinfection. The efficiency of the process used must be recognised and validated in principle (e.g. listed under disinfectants and disinfection procedures tested and recognised by Robert-Koch-Institute / DGHM). When using other procedures (e.g. a manual procedure), proof and process efficiency in principle must be provided within the scope of validation. Proof in principle of the suitability of the handles for efficient cleaning / disinfection was provided using a cyclic cleaning system (Netsch-Bellmed T-600-IUDT/AN, programme 2 for small parts; code B). It is not allowed to use agents / disinfectants, which contain the following substances, as these may cause changes in the material: - High-concentration organic and inorganic acids - Chlorinated hydrocarbons - 2-ethoxyethanol 59100002 Edition 07 05.06.2002 / Bak Page 9/25
Page 1 and 2: MACH 130 FP Wall model Directions f
Page 3 and 4: MACH 130 FP Wall model 1. Safety in
Page 5 and 6: MACH 130 FP Wall model 3. Mounting
Page 7: MACH 130 FP Wall model 67,68 4. Ope
Page 11 and 12: MACH 130 FP Wall model 15 Alc. ≤
Page 13 and 14: MACH 130 FP Wall model screw driver
Page 15 and 16: MACH 130 FP Wall model 26,65 X X 6.
Page 17 and 18: MACH 130 FP Wall model 3 S X 2 S S
Page 19 and 20: MACH 130 FP Wall model 7.1 Technica
Page 21 and 22: MACH 130 FP Wall model 8.2 Specific
Page 23 and 24: MACH 130 FP Wall model 10.2 Wall at
Page 25: MACH 130 FP Wall model Spare parts

MACH 130 FP Mains Voltage 230V / 120V - Dr. Mach

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?