MACH 130 FP Mains Voltage 230V / 120V - Dr. Mach

More documents

Recommendations

Info

MACH 130 FP Wall model 16b 14 16b III II II I III III 2 52,53 15 16a I marking 15 Dr. Mach Lamps and Engineering • Press filter disk 14 carefully against two springs 16a (I). Attention: Touch the filter disk only with a non-fluffy cloth. • Press the other two springs 16b to the edge (II) and lift the filter disk (III). • Insert the new filter disk in reverse order. Make sure that the marking points to the upper side of the lamp housing as shown in the figure. The reverse side of the disk is steam finished. Only use filter disks, that have been cleaned properly. • Fix the bottom part 2 of the lamp housing with the three screws S. • Fix the cover 3, so that the two arrest pins snap in. 6.3.5 Changing the protective disk In case you notice a impediment of the light quality because of a dull protective disk, it may be necessary to change the disk. To change the protective disk proceed as follows: • Turn off the lamp. • Remove the bottom part 2 of the lamp housing as described at point 4.4.4. • Loosen six screws 52/54 and remove them including the washers 53. Attention: Hold the protective disk 15 carefully, it is loosen now. • Remove the protective disk 15. • Insert the new protective disk, so that it is placed even to the bottom part of the lamp housing. • Fix the protective disk with six screws 52/54 and washers 53. Attention: Only use protective disks, that have been cleaned as described at point 3.2. • Fix the bottom part 2 of the lamp housing. • Fix the cover 3, so that the arrest pins snap in. 59100002 Edition 07 05.06.2002 / Bak Page 18/25
MACH 130 FP Wall model 7.1 Technical data 7. Data Mains voltage 230 Volt ~ Wechselstrom alternating current Pr Primärseitig 230V / 0,43A primary side Sek Sekundärseitig 23V / 2,19A secondary side Leistungsaufnahme 50VA power consumption Hz Hertz-Frequenz 50 / 60Hz frequency Hertz Sicherung UR 5x20/1,25A/250V AC/t fuse Schutzgrad Typ „B“ class of protection Mains voltage 120 Volt ~ Wechselstrom alternating current Pr Primärseitig 120V / 0,86A primary side Sek Sekundärseitig 21V / 2,19A secondary side Leistungsaufnahme 50VA power consumption Hz Hertz-Frequenz 50 / 60Hz frequency Hertz Sicherung UR 5x20/1,25A/250V AC/t fuse Schutzgrad Typ „B“ class of protection 7.2 Wiring Switch Mach 130 FP mains voltage 230V/120V built in toroid transformer Toroid transformer Halogen bulb 1 2 3 Dr. Mach Lamps and Engineering 59100002 Edition 07 05.06.2002 / Bak Page 19/25 N L P
Page 1 and 2: MACH 130 FP Wall model Directions f
Page 3 and 4: MACH 130 FP Wall model 1. Safety in
Page 5 and 6: MACH 130 FP Wall model 3. Mounting
Page 7 and 8: MACH 130 FP Wall model 67,68 4. Ope
Page 9 and 10: MACH 130 FP Wall model V 45 Cleanin
Page 11 and 12: MACH 130 FP Wall model 15 Alc. ≤
Page 13 and 14: MACH 130 FP Wall model screw driver
Page 15 and 16: MACH 130 FP Wall model 26,65 X X 6.
Page 17: MACH 130 FP Wall model 3 S X 2 S S
Page 21 and 22: MACH 130 FP Wall model 8.2 Specific
Page 23 and 24: MACH 130 FP Wall model 10.2 Wall at
Page 25: MACH 130 FP Wall model Spare parts

MACH 130 FP Mains Voltage 230V / 120V - Dr. Mach

Create successful ePaper yourself

Delete template?

Save as template?