MACH 130 FP Mains Voltage 230V / 120V - Dr. Mach

More documents

Recommendations

Info

MACH 130 FP Wall model 6. Maintenance Dr. Mach Lamps and Engineering The lamp has been designed and built so that regular maintenance intervals are not necessary. In order to keep the system easy running throughout its life span we recommend that the hinges be greased once a year with an acid-free grease. The lamp body may only be dismantled from the spring arm in reverse order to its assembly after the assembly locking device has been inserted and tightened since the arm is under spring tension. Attention: Screw the transport safeguard into place in the spring arm before removing the lights. F F 6.1 Adjustments at the wall attachment ♦ Adjusting the spring force The spring arm is correctly adjusted when the light remains in position at every set height and can be moved more easily upwards than downwards. Should you discover that the light no longer remains at its set height, proceed as follows: • Turn off the lamp. • Push the two circular areas F on the sides carefully apart. Remove the cover from the front. • Move the spring arm into a position in which the hole nut is visible. Attention: If the max. height of the spring arm is limited, the hole nut may in certain circumstances remain invisible. In this case consult your dealer or Dr. Mach directly. • Place the key bolt that can be found below the cover on the top of the spring arm in the hole and turn accordingly. Use only the enclosed key bolt since a screwdriver could break. Proceed as follows depending on the movement of the light. a. Lamp moves down on its own - turn bolt in the direction of the „+“ mark. b. Lamp moves up on its own - turn bolt in the direction of the „−“ mark. 59100002 Edition 07 05.06.2002 / Bak Page 12/25
MACH 130 FP Wall model screw driver JS X 4 10 A ♦ Height adjustment Dr. Mach Lamps and Engineering Adjust the height to prevent any impact from the articulated arm on the ceiling. • Spread the cover caps in the upper and lower slot J using a screwdriver and take them out. The drilled nut is visible now. • Turn the drilled nut using the key in the direction of the „ – “ mark (shown on the spring arm), until the required height position has been reached. Do not use a screwdriver, since it could break. Remark: 40-50 rotational movements are necessary for 10cm height adjustment. • Store the key bolt and replace the cover caps. 6.2 Adjustments at the lamp head ♦ Adjusting the movability of the handle for focusing – Mach 130 FP In case you notice that the handle moves to easily or to heavily, it may be necessary to adjust its movability. To adjust the movability of the handle proceed as follows: • Turn off the lamp. • Loosen the housing cap arrest by pushing the arrest pin X (e.g. with a ball pen). • Remove cover 4 of the lamp. • You can adjust the movability of the handle by turning the levelling screw with a screwdriver. - Clockwise – stronger - Anticlockwise - easier It is not necessary to remove the cover 4, which closes the adjustment. ♦ Manipulating the lamp The lamp bow 10 enables a perfect movability and positioning of the lamps Mach 130 FP. The brake force in the axis A is set. It is usually not necessary to adjust it. 59100002 Edition 07 05.06.2002 / Bak Page 13/25
Page 1 and 2: MACH 130 FP Wall model Directions f
Page 3 and 4: MACH 130 FP Wall model 1. Safety in
Page 5 and 6: MACH 130 FP Wall model 3. Mounting
Page 7 and 8: MACH 130 FP Wall model 67,68 4. Ope
Page 9 and 10: MACH 130 FP Wall model V 45 Cleanin
Page 11: MACH 130 FP Wall model 15 Alc. ≤
Page 15 and 16: MACH 130 FP Wall model 26,65 X X 6.
Page 17 and 18: MACH 130 FP Wall model 3 S X 2 S S
Page 19 and 20: MACH 130 FP Wall model 7.1 Technica
Page 21 and 22: MACH 130 FP Wall model 8.2 Specific
Page 23 and 24: MACH 130 FP Wall model 10.2 Wall at
Page 25: MACH 130 FP Wall model Spare parts

MACH 130 FP Mains Voltage 230V / 120V - Dr. Mach

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?