UFO Service V2 Mar02 625-030.pdf
UFO Service V2 Mar02 625-030.pdf UFO Service V2 Mar02 625-030.pdf
Section 17 SWING-UP PERFORATOR SERVICE Mounting Spindle Shoulder Bushes M 10 Nuts M 10 Bolt M 8 Nut Flats - Wrench Drive Gears Solid Hubs - Lower Lower Perforator Shaft Tyred Hubs - Upper Upper Perforator Shaft Swing-up Perforating Unit ......................................... Fig 17.11 17.2 .....Swing-up Perforating Unit - Dismantling Once the unit is off the machine, the perforator shafts can be removed from the unit. The shafts are removed by releasing the M8 nut whilst stopping the shafts rotating by using a 13mm wrench on the flats. With the M8 nuts removed, the shafts are passed through the unit sliding off all the hubs in the process. Upon re-assembly, fit the hubs correctly with the solid hubs on the lower shaft with their grub screws facing the drive side, and the tyred hubs on the upper shaft with their grub screws facing the operator side. PAGE 46 FOLDING
MANUAL CROSS-FOLD UNIT Section 18 Circuit Diagram Cross-fold Control Box ......................Fig 18.11 SYSTEMS PAGE 47
- Page 1 and 2: FOLDING SYSTEM SERVICE MANUAL Morga
- Page 3 and 4: MANUAL INTRODUCTION Pan head and Cr
- Page 5 and 6: MANUAL INDEX Section .. 11 ......Ca
- Page 7 and 8: MANUAL COVERS Section 1 ‘Pozi-dri
- Page 9 and 10: MANUAL MANIFOLDS Section 2 2.2 ....
- Page 11 and 12: MANUAL SIDE - LAY Section 4 3.2 ...
- Page 13 and 14: MANUAL FEED BED ASSEMBLY Section 5
- Page 15 and 16: MANUAL FEED DRIVE BELT Section 6 M4
- Page 17 and 18: MANUAL FEED DRIVE GEARBOX Section 7
- Page 19 and 20: MANUAL OUTER FOLD ROLLERS Section 8
- Page 21 and 22: MANUAL OUTER FOLD ROLLERS Section 8
- Page 23 and 24: MANUAL OUTER FOLD ROLLERS Section 8
- Page 25 and 26: MANUAL CENTRE FOLD ROLLER Section 9
- Page 27 and 28: MANUAL PERFORATOR SHAFTS Section 10
- Page 29 and 30: MANUAL CALLIPER CABLE Section 11 11
- Page 31 and 32: MANUAL FOLD PLATES Section 12 12.2
- Page 33 and 34: MANUAL FOLD PLATES Section 12 Stop
- Page 35 and 36: MANUAL FOLD PLATES Section 12 12.6
- Page 37 and 38: MANUAL FOLD PLATES Section 12 9. In
- Page 39 and 40: MANUAL CONTROL SYSTEM Section 13 Fu
- Page 41 and 42: MANUAL COMPRESSOR Section 14 In-lin
- Page 43 and 44: MANUAL SUCTION CONTROL VALVE Sectio
- Page 45: MANUAL ELECTRIC DELIVERY Section 16
- Page 49 and 50: MANUAL CROSS-FOLD UNIT Section 18 1
- Page 51 and 52: MANUAL CROSSFOLD UNIT Section 18 Be
- Page 53 and 54: MANUAL TROUBLE-SHOOTING Section 19
- Page 55 and 56: MANUAL TROUBLE-SHOOTING Section 19
- Page 57 and 58: MANUAL TROUBLE-SHOOTING Section 19
- Page 59 and 60: MANUAL TROUBLE-SHOOTING Section 20
Section 17<br />
SWING-UP PERFORATOR<br />
SERVICE<br />
Mounting Spindle<br />
Shoulder Bushes<br />
M 10 Nuts<br />
M 10 Bolt<br />
M 8 Nut<br />
Flats - Wrench<br />
Drive Gears<br />
Solid Hubs - Lower<br />
Lower Perforator Shaft<br />
Tyred Hubs - Upper<br />
Upper Perforator Shaft<br />
Swing-up Perforating Unit ......................................... Fig 17.11<br />
17.2 .....Swing-up Perforating Unit - Dismantling<br />
Once the unit is off the machine, the perforator shafts can be<br />
removed from the unit.<br />
The shafts are removed by releasing the M8 nut whilst stopping the<br />
shafts rotating by using a 13mm wrench on the flats.<br />
With the M8 nuts removed, the shafts are passed through the unit<br />
sliding off all the hubs in the process.<br />
Upon re-assembly, fit the hubs correctly with the solid hubs on the<br />
lower shaft with their grub screws facing the drive side, and the<br />
tyred hubs on the upper shaft with their grub screws facing the<br />
operator side.<br />
PAGE 46<br />
FOLDING