UFO Service V2 Mar02 625-030.pdf

More documents

Recommendations

Info

Section 8 OUTER FOLD ROLLERS SERVICE Machine Side-Frame - Operator Side Spring Block Adjusting Screw & Locknut - Roller Pressure Spring Spring Pad Calliper Adjusting Screw & Locknut - Spring Pressure Calliper Pad Calliper Jaw Gears Grub Screws - Drive Gears Fold Roller - Moving Linear Bearings Calliper Plate - Inner Main Roller - Centre Fold Rollers ................................................................ Fig 8.11 8.1 .......Outer Fold Rollers - Removal Each of the fold rollers are removed to the operator side so the following instructions apply to the operator side calliper assemblies only. Remove the pressure spring lock-nut (using a shortened 2.5mm allen key) and unscrew the pressure screw enough to clear the spring pad. PAGE 18 FOLDING
MANUAL OUTER FOLD ROLLERS Section 8 Remove the nut and washer securing the spring block and remove the block, taking care to hold the spring to avoid losing it and the spring pad. Release both grub screws in both the large gear and the drive gear, five full turns, to clear the shaft and remove the gear. Remove the calliper jaw by removing the two socket head cap screws. Remove the two bolts securing the linear bearings to the backplate and remove both bearings and back-plate. The calliper and roller may now be released from the side-frames and the calliper can be pulled off the roller bearing. The drive side bearing and calliper remain undisturbed. Note ........Take care of the circular shims that are fitted between the calliper and the bearing. They should be kept safe and used when replacing the roller. The roller is replaced in the reverse sequence. However, before fitting and setting the pressure spring, the linear bearings must be correctly adjusted - see the following sections for the procedures. 8.2 .......Outer Fold Rollers - Linear Bearings The fold rollers are located in moving callipers which must move freely up and down without any lateral movement. This is achieved by setting the linear bearings very carefully which is carried out at the factory and will require no further attention unless the rollers are removed. Before any attempt is made to set the linear bearings, the pressure spring must be removed,(as in section 8.1 above). This is so that it is easier to feel the tightness or slackness in the moving calliper. SYSTEMS PAGE 19
Page 1 and 2: FOLDING SYSTEM SERVICE MANUAL Morga
Page 3 and 4: MANUAL INTRODUCTION Pan head and Cr
Page 5 and 6: MANUAL INDEX Section .. 11 ......Ca
Page 7 and 8: MANUAL COVERS Section 1 ‘Pozi-dri
Page 9 and 10: MANUAL MANIFOLDS Section 2 2.2 ....
Page 11 and 12: MANUAL SIDE - LAY Section 4 3.2 ...
Page 13 and 14: MANUAL FEED BED ASSEMBLY Section 5
Page 15 and 16: MANUAL FEED DRIVE BELT Section 6 M4
Page 17: MANUAL FEED DRIVE GEARBOX Section 7
Page 21 and 22: MANUAL OUTER FOLD ROLLERS Section 8
Page 23 and 24: MANUAL OUTER FOLD ROLLERS Section 8
Page 25 and 26: MANUAL CENTRE FOLD ROLLER Section 9
Page 27 and 28: MANUAL PERFORATOR SHAFTS Section 10
Page 29 and 30: MANUAL CALLIPER CABLE Section 11 11
Page 31 and 32: MANUAL FOLD PLATES Section 12 12.2
Page 33 and 34: MANUAL FOLD PLATES Section 12 Stop
Page 35 and 36: MANUAL FOLD PLATES Section 12 12.6
Page 37 and 38: MANUAL FOLD PLATES Section 12 9. In
Page 39 and 40: MANUAL CONTROL SYSTEM Section 13 Fu
Page 41 and 42: MANUAL COMPRESSOR Section 14 In-lin
Page 43 and 44: MANUAL SUCTION CONTROL VALVE Sectio
Page 45 and 46: MANUAL ELECTRIC DELIVERY Section 16
Page 47 and 48: MANUAL CROSS-FOLD UNIT Section 18 C
Page 49 and 50: MANUAL CROSS-FOLD UNIT Section 18 1
Page 51 and 52: MANUAL CROSSFOLD UNIT Section 18 Be
Page 53 and 54: MANUAL TROUBLE-SHOOTING Section 19

UFO Service V2 Mar02 625-030.pdf

Create successful ePaper yourself

Delete template?

Save as template?