UFO Service V2 Mar02 625-030.pdf

More documents

Recommendations

Info

Section 5 FEED BED ASSEMBLY SERVICE Roller Retainer Brackets Conveyor Idler Shaft Assembly Roller - Feed Belt Idler Shaft Brackets Feed Bed Stiffener Insert - Feed Bed Feed Belt Counter Sensor & Stiffener Conveyor Drive Shaft Vacuum Roller Assembly Couplings Gas Strut Drive Shaft Bearing Housings Torque Discs - Coupling Feed Bed - Underside ................................................. Fig 5.11 PAGE 12 FOLDING
MANUAL FEED BED ASSEMBLY Section 5 5.1 .......Feed Belt - Removal Remove the sidelay as described in section 4, remove the four screws securing the conveyor idler shaft brackets and remove the idler shaft assembly. Remove the four screws securing the conveyor drive shaft bearing housings and remove the drive shaft as an assembly. Note ........Take care not to lose the roller retaining brackets or the torque disc (from the coupling), when removing the shafts. (See Fig. 6.11) Remove the counter sensor and it’s bracket from the drive end stiffener and remove the six screws securing both stiffeners to the feed bed, (do not remove the screws which secure the insert to the stiffeners), then carefully draw the insert and stiffeners from the machine and remove the feed belt. Note ........On re-assembly, fit the new belt according to the direction arrow on the reverse side of the belt. 5.2 .......Counter Sensor The counter sensor is located beneath the feed bed as shown in fig. 5.11 and its alignment is checked as follows:- Remove the control box lid (see section 13) and set a volt meter to read 5 Volts DC. Connect the positive lead to TP3 and the negative lead to TP1 on the counter PCB. (see fig 13.12) The signal should rise to 5.0 Volts DC when the detector is not reflecting, (ie when covered by a sheet of paper), and drop to less than 0.5 Volts DC when reflecting, (no paper). The detector and reflector must be cleaned and the reflector adjusted to obtain the lowest value when reflecting, (typically 0.2 Volts). SYSTEMS PAGE 13
Page 1 and 2: FOLDING SYSTEM SERVICE MANUAL Morga
Page 3 and 4: MANUAL INTRODUCTION Pan head and Cr
Page 5 and 6: MANUAL INDEX Section .. 11 ......Ca
Page 7 and 8: MANUAL COVERS Section 1 ‘Pozi-dri
Page 9 and 10: MANUAL MANIFOLDS Section 2 2.2 ....
Page 11: MANUAL SIDE - LAY Section 4 3.2 ...
Page 15 and 16: MANUAL FEED DRIVE BELT Section 6 M4
Page 17 and 18: MANUAL FEED DRIVE GEARBOX Section 7
Page 19 and 20: MANUAL OUTER FOLD ROLLERS Section 8
Page 25 and 26: MANUAL CENTRE FOLD ROLLER Section 9
Page 27 and 28: MANUAL PERFORATOR SHAFTS Section 10
Page 29 and 30: MANUAL CALLIPER CABLE Section 11 11
Page 31 and 32: MANUAL FOLD PLATES Section 12 12.2
Page 33 and 34: MANUAL FOLD PLATES Section 12 Stop
Page 35 and 36: MANUAL FOLD PLATES Section 12 12.6
Page 37 and 38: MANUAL FOLD PLATES Section 12 9. In
Page 39 and 40: MANUAL CONTROL SYSTEM Section 13 Fu
Page 41 and 42: MANUAL COMPRESSOR Section 14 In-lin
Page 43 and 44: MANUAL SUCTION CONTROL VALVE Sectio
Page 45 and 46: MANUAL ELECTRIC DELIVERY Section 16
Page 47 and 48: MANUAL CROSS-FOLD UNIT Section 18 C
Page 49 and 50: MANUAL CROSS-FOLD UNIT Section 18 1
Page 51 and 52: MANUAL CROSSFOLD UNIT Section 18 Be
Page 53 and 54: MANUAL TROUBLE-SHOOTING Section 19

UFO Service V2 Mar02 625-030.pdf

Create successful ePaper yourself

Delete template?

Save as template?