2009 Pilot Remote Control Engine Starter - Bernardi Parts
2009 Pilot Remote Control Engine Starter - Bernardi Parts 2009 Pilot Remote Control Engine Starter - Bernardi Parts
20. Lower the tilt lever and pull the steering wheel out. 4 RETAINING TABS UPPER STEERING COLUMN COVER 2 SELF-TAPPING SCREWS Routing the Engine Starter Harness 23. Attach the one 40 A fuse label to the engine starter harness fuse block. FUSE LABEL (3 A) FUSE LABEL (40 A) Push. TILT LEVER 21. Remove the upper steering column cover: • Remove the two self-tapping screws. 792404CE • Push the upper cover inward at the areas shown to release the four retaining tabs. 22. Remove the lower steering column cover (two selftapping screws and one screw). FUSE BLOCK ENGINE STARTER HARNESS 24. Attach the 3 A fuse label to the engine starter harness fuse block. 840903AY 25. Install the two relays to the engine starter harness relay blocks. LOWER STEERING COLUMN COVER (2) 4- RELAYS ENGINE STARTER HARNESS RELAY BLOCK SCREW 2 SELF-TAPPING SCREWS 792003BY 792405AE 6 of 21 AII 39404-39646 (0805) © 2008 American Honda Motor Co., Inc. – All Rights Reserved.
26. Plug the engine starter harness 28-pin connector into the control unit. 28. Secure the control unit to the vehicle bracket with a 6 mm flange nut. STEERING WHEEL 28-PIN CONNNECTOR CONTROL UNIT STEERING SHAFT ENGINE STARTER HARNESS 792004AY 27. Install the control unit bracket to the control unit. VEHICLE BRACKET Hold against the brackets. CONTROL UNIT CONTROL UNIT BRACKET CONTROL UNIT BRACKET CONTROL UNIT VEHICLE BRACKET FLANGE NUT, 6 mm CONTROL UNIT STEERING SHAFT 792401CY 792005AY © 2008 American Honda Motor Co., Inc. – All Rights Reserved. AII 39404-39646 (0805) 7 of 21
- Page 1 and 2: INSTALLATION INSTRUCTIONS Accessory
- Page 3 and 4: Setting the Control Unit 3. Touch t
- Page 5: 14. Using a plastic trim tool, open
- Page 9 and 10: 34. Secure the 4-pin connector to t
- Page 11 and 12: 45. Route the engine starter harnes
- Page 13 and 14: 53. Secure the joint of the engine
- Page 15 and 16: 63. Route the antenna cable to the
- Page 17 and 18: 72. Using isopropyl on a shop towel
- Page 19 and 20: vehicle’s VIN will be required to
- Page 21: 6. Check the operation of the trans
20. Lower the tilt lever and pull the steering wheel out.<br />
4 RETAINING<br />
TABS<br />
UPPER<br />
STEERING<br />
COLUMN<br />
COVER<br />
2 SELF-TAPPING<br />
SCREWS<br />
Routing the <strong>Engine</strong> <strong>Starter</strong> Harness<br />
23. Attach the one 40 A fuse label to the engine starter<br />
harness fuse block.<br />
FUSE LABEL<br />
(3 A)<br />
FUSE LABEL<br />
(40 A)<br />
Push.<br />
TILT LEVER<br />
21. Remove the upper steering column cover:<br />
• Remove the two self-tapping screws.<br />
792404CE<br />
• Push the upper cover inward at the areas shown<br />
to release the four retaining tabs.<br />
22. Remove the lower steering column cover (two selftapping<br />
screws and one screw).<br />
FUSE BLOCK<br />
ENGINE<br />
STARTER<br />
HARNESS<br />
24. Attach the 3 A fuse label to the engine starter<br />
harness fuse block.<br />
840903AY<br />
25. Install the two relays to the engine starter harness<br />
relay blocks.<br />
LOWER<br />
STEERING<br />
COLUMN<br />
COVER<br />
(2) 4- RELAYS<br />
ENGINE<br />
STARTER<br />
HARNESS<br />
RELAY<br />
BLOCK<br />
SCREW<br />
2 SELF-TAPPING<br />
SCREWS<br />
792003BY<br />
792405AE<br />
6 of 21 AII 39404-39646 (0805)<br />
© 2008 American Honda Motor Co., Inc. – All Rights Reserved.
Change language