2009 Pilot Remote Control Engine Starter - Bernardi Parts
2009 Pilot Remote Control Engine Starter - Bernardi Parts 2009 Pilot Remote Control Engine Starter - Bernardi Parts
57. Starting near the antenna end of the cable, wrap three urethane tapes around the antenna cable at the measurements shown. 59. Secure the template to the windshield with masking tapes by aligning it with the edge of the black ceramic paint as shown. ANTENNA CABLE ANTENNA BLACK CERAMIC PAINT 410 mm 40 mm URETHANE TAPE 40 mm FRONT WINDOW 701015AB MIRROR TEMPLATE MASKING TAPES 6N3002AK 58. Using scissors, cut out the template. 60. Using isopropyl alcohol on a shop towel, clean the area where the antenna will attach. Allow to dry before proceeding. Cut out. TEMPLATE Cut out. HEADLINER TEMPLATE 7209041K PLATE ANTENNA ADHESIVE BACKING 6N3004BK 61. Remove the adhesive backing from the antenna, insert the antenna plate under the headliner, and attach the antenna to the windshield aligning the template. 62. Remove the template. 14 of 21 AII 39404-39646 (0805) © 2008 American Honda Motor Co., Inc. – All Rights Reserved.
63. Route the antenna cable to the left side of the vehicle, and push it into the headliner as shown. Be careful not to crease the headliner. HEADLINER 65. Clean the vehicle panel surface where the urethane tape will attach with isopropyl alcohol. Secure the antenna cable to the vehicle panel with the remaining part of the urethane tape you cut in step 40. Be careful no to crease the headliner. Remains of urethane tape cut in step 40. HEADLINER VEHICLE PANEL ANTENNA CABLE 6N30050K ANTENNA CABLE URETHANE TAPE 64. Clean the vehicle panel surface where the urethane tape will attach with isopropyl alcohol. Secure the antenna cable to the vehicle panel with the smaller part urethane tape that you cut into two in step 40. Be careful not to crease the headliner. 701017BB 66. Route the antenna cable along the left A-pillar and secure the antenna cable to the vehicle harness with four wire ties as shown. VEHICLE PANEL ANTENNA CABLE ANTENNA CABLE HEADLINER 1/2 of urethane tape cut in step 40. URETHANE TAPE VEHICLE HARNESS 4 WIRE TIES LEFT A-PILLAR 701016BB 792711AY © 2008 American Honda Motor Co., Inc. – All Rights Reserved. AII 39404-39646 (0805) 15 of 21
- Page 1 and 2: INSTALLATION INSTRUCTIONS Accessory
- Page 3 and 4: Setting the Control Unit 3. Touch t
- Page 5 and 6: 14. Using a plastic trim tool, open
- Page 7 and 8: 26. Plug the engine starter harness
- Page 9 and 10: 34. Secure the 4-pin connector to t
- Page 11 and 12: 45. Route the engine starter harnes
- Page 13: 53. Secure the joint of the engine
- Page 17 and 18: 72. Using isopropyl on a shop towel
- Page 19 and 20: vehicle’s VIN will be required to
- Page 21: 6. Check the operation of the trans
57. Starting near the antenna end of the cable, wrap<br />
three urethane tapes around the antenna cable at<br />
the measurements shown.<br />
59. Secure the template to the windshield with masking<br />
tapes by aligning it with the edge of the black ceramic<br />
paint as shown.<br />
ANTENNA<br />
CABLE<br />
ANTENNA<br />
BLACK<br />
CERAMIC<br />
PAINT<br />
410 mm<br />
40 mm<br />
URETHANE<br />
TAPE<br />
40<br />
mm<br />
FRONT<br />
WINDOW<br />
701015AB<br />
MIRROR<br />
TEMPLATE<br />
MASKING<br />
TAPES<br />
6N3002AK<br />
58. Using scissors, cut out the template.<br />
60. Using isopropyl alcohol on a shop towel, clean the<br />
area where the antenna will attach. Allow to dry<br />
before proceeding.<br />
Cut out.<br />
TEMPLATE<br />
Cut out.<br />
HEADLINER<br />
TEMPLATE<br />
7209041K<br />
PLATE<br />
ANTENNA<br />
ADHESIVE<br />
BACKING<br />
6N3004BK<br />
61. Remove the adhesive backing from the antenna,<br />
insert the antenna plate under the headliner, and<br />
attach the antenna to the windshield aligning the<br />
template.<br />
62. Remove the template.<br />
14 of 21 AII 39404-39646 (0805)<br />
© 2008 American Honda Motor Co., Inc. – All Rights Reserved.
Change language