2009 Pilot Remote Control Engine Starter - Bernardi Parts
2009 Pilot Remote Control Engine Starter - Bernardi Parts 2009 Pilot Remote Control Engine Starter - Bernardi Parts
39. Secure the 2-pin connectors to the vehicle harness with one wire tie. 42. Route the engine starter harness ground terminal as shown. FUSE BOX ENGINE STARTER HARNESS PARKING BRAKE LEVER ENGINE STARTER HARNESS GROUND TERMINAL VEHICLE HARNESS WIRE TIE 2-PIN CONNECTORS STEERING SHAFT 792707EY 40. Cut the urethane tape into two equal parts, and cut one half of the urethane tape to the dimension shown. PARKING BRAKE LEVER VEHICLE BOLT (Discard.) GROUND BOLT FUSE BOX 43. Remove and discard the vehicle bolt near the parking brake lever, install the engine starter harness ground terminal with the ground bolt including the kit. 792708BY 44. Loosely secure the engine starter harness to the vehicle harness with two wire ties. 2 WIRE TIES (Loosely secure.) 10 mm URETHANE TAPE URETHANE TAPE VEHICLE BRACKET 7D2401AB 41. Clean the vehicle bracket surface where the urethane tape will attach with isopropyl alcohol. Attach the urethane tape that you cut in step 40 to the vehicle bracket as shown. ENGINE STARTER HARNESS VEHICLE HARNESS 792709BY 10 of 21 AII 39404-39646 (0805) © 2008 American Honda Motor Co., Inc. – All Rights Reserved.
45. Route the engine starter harness 5-pin connector to the ignition switch. IGNITION SWITCH 47. Unplug the vehicle 8-pin connector, and plug it into the engine starter harness 8-pin connectors. Plug the remaining engine starter harness 8-pin connector into the wiper switch. 5-PIN CONNECTOR 8-PIN CONNECTORS VEHICLE 8-PIN CONNECTOR ENGINE STARTER HARNESS 792601BY BODY SWITCH ENGINE STARTER HARNESS WIPER SWITCH 792702AY 48. Route the engine starter harness into the harness case. 46. Unplug the vehicle 12-pin connector, and plug it into the engine starter harness 12-pin connectors. Plug the remaining engine starter harness 12-pin connector into the turn signal switch. HARNESS CASE VEHICLE 12-PIN CONNECTOR 12-PIN CONNECTORS ENGINE STARTER HARNESS TURN SIGNAL SWITCH FRONT ENGINE STARTER HARNESS 792703AY BODY SWITCH 792701AY © 2008 American Honda Motor Co., Inc. – All Rights Reserved. AII 39404-39646 (0804) 11 of 21
- Page 1 and 2: INSTALLATION INSTRUCTIONS Accessory
- Page 3 and 4: Setting the Control Unit 3. Touch t
- Page 5 and 6: 14. Using a plastic trim tool, open
- Page 7 and 8: 26. Plug the engine starter harness
- Page 9: 34. Secure the 4-pin connector to t
- Page 13 and 14: 53. Secure the joint of the engine
- Page 15 and 16: 63. Route the antenna cable to the
- Page 17 and 18: 72. Using isopropyl on a shop towel
- Page 19 and 20: vehicle’s VIN will be required to
- Page 21: 6. Check the operation of the trans
45. Route the engine starter harness 5-pin connector to<br />
the ignition switch.<br />
IGNITION<br />
SWITCH<br />
47. Unplug the vehicle 8-pin connector, and plug it into<br />
the engine starter harness 8-pin connectors. Plug<br />
the remaining engine starter harness 8-pin<br />
connector into the wiper switch.<br />
5-PIN<br />
CONNECTOR<br />
8-PIN<br />
CONNECTORS<br />
VEHICLE<br />
8-PIN<br />
CONNECTOR<br />
ENGINE<br />
STARTER<br />
HARNESS<br />
792601BY<br />
BODY<br />
SWITCH<br />
ENGINE<br />
STARTER<br />
HARNESS<br />
WIPER<br />
SWITCH<br />
792702AY<br />
48. Route the engine starter harness into the harness<br />
case.<br />
46. Unplug the vehicle 12-pin connector, and plug it into<br />
the engine starter harness 12-pin connectors. Plug<br />
the remaining engine starter harness 12-pin<br />
connector into the turn signal switch.<br />
HARNESS<br />
CASE<br />
VEHICLE<br />
12-PIN<br />
CONNECTOR<br />
12-PIN<br />
CONNECTORS<br />
ENGINE<br />
STARTER<br />
HARNESS<br />
TURN<br />
SIGNAL<br />
SWITCH<br />
FRONT<br />
ENGINE<br />
STARTER<br />
HARNESS<br />
792703AY<br />
BODY<br />
SWITCH<br />
792701AY<br />
© 2008 American Honda Motor Co., Inc. – All Rights Reserved.<br />
AII 39404-39646 (0804)<br />
11 of 21