SJ700-2 Instruction Manual NT204DX - Hitachi America, Ltd.

Chapter 4 Explanation of Functions
4.2.11 External analog input setting (O, OI, and O2)
The inverter has the following three types of external analog input
terminals:
O-L terminal: 0 to 10 V
OI-L terminal: 4 to 20 mA
O2-L terminal: -10 to 10 V
Related code
A005: [AT] selection
A006: [O2] selection
C001 to C008: Terminal [1] to [8] functions
The table below lists the settings of the external analog input terminals.
Item
[AT]
selection
[O2]
selection
Function
code
A005
A006
Data
Description
00
Switching between the O and OI Turning on the AT terminal enables the OI-L terminal.
terminals with the AT terminal
Turning on the AT terminal enables the O-L terminal.
01
Switching between the O and O2 Turning on the AT terminal enables the O2-L terminal.
terminals with the AT terminal
Turning on the AT terminal enables the O-L terminal.
(02)
(Valid only when the OPE-SR is used)
Switching between the O terminal and
the control with the AT terminal
Turning on the AT terminal enables the pot on
OPE-SR terminal.
Turning on the AT terminal enables the O-L terminal.
(03)
(Valid only when the OPE-SR is used)
Switching between the OI terminal and
the control with the AT terminal
Turning on the AT terminal enables the pot on
OPE-SR terminal.
Turning on the AT terminal enables the OI-L terminal.
(Valid only when the OPE-SR is used) Turning on the AT terminal enables the pot on
(04) Switching between the O2 terminal
OPE-SR terminal.
and the control with the AT terminal Turning on the AT terminal enables the O2-L terminal.
00 Using the O2 terminal independently
01
Using the O2 terminal for auxiliary frequency command (nonreversible) in addition to the O and
OI terminals
02
Using the O2 terminal for auxiliary frequency command (reversible) in addition to the O and OI
terminals
03 Disabling the O2 terminal
Note that whether frequency commands are input to the O2-L terminal and whether the motor operation is
reversible depend on the combination of settings of functions "A005" and "A006" and whether function "16"
(AT) is assigned to an intelligent input terminal as shown in the table below.
When the motor operation is reversible, the inverter operates the motor in a reverse direction if the sum of
the frequencies specified by the main frequency and auxiliary frequency commands is less than 0 (even
when the forward operation [FW] terminal is on). Even when no wire is connected to the 02 terminal,
reverse operation of the motor may occur and prolong the acceleration time if the output voltage fluctuates
near 0 V.
When the AT
function is
assigned to an
intelligent input
terminal
When the AT
function is not
assigned to any
intelligent input
terminal
A006
A005
AT
terminal
Main frequency command
Whether to input an auxiliary
frequency command
(via the O2-L terminal)
Reversible/
nonreversible
00,03
00
OFF O-L terminal No input
ON OI-L terminal No input
Nonreversible
01
OFF O-L terminal No input
ON O2-L terminal No input Reversible
00 OFF O-L terminal Input
(Example 1) ON OI-L terminal Input
Nonreversible
01
OFF O-L terminal Input
01
ON O2-L terminal No input Reversible
00 OFF O-L terminal Input
(Example 2) ON OI-L terminal Input
02
Reversible
OFF O-L terminal Input
01
ON O2-L terminal No input
00 - - O2-L terminal No input Reversible
01 - -
Addition of signals on O-L and
OI-L terminals
Input
Nonreversible
02 - -
Addition of signals on O-L and
OI-L terminals
Input
Reversible
03 - -
Addition of signals on O-L and
OI-L terminals
No input
Nonreversible
4 - 12