SJ700-2 Instruction Manual NT204DX - Hitachi America, Ltd.

More documents

Recommendations

Info

Appendix (2) Copying the parameter settings If you use an optional remote operator (SRW-OJ or SRW-OEX), you can copy (import) the parameter settings from the SJ300 series into the SJ700 series. Note, however, that you cannot copy the parameter settings from the SJ700 series to the SJ300 series because the SJ700 series has many new functions and additional parameters. Precaution: Copying of the data on an optional operator (SRW or SRW-EX) If you copy parameter data from the SJ700 or SJ300 series inverter in which the slide switch SW1 is set to OFF to the SJ700 series inverter in which the slide switch SW1 is set to ON, the operator may momentarily display an error message "R-ERROR COPY ROM." This event occurs because the data on intelligent input terminals [1] and [3] cannot be copied because the copy-destination SJ700 series has exclusively assigned special functions to these terminals according to the ON setting of the slide switch SW1. Other parameter data is copied. In such cases, confirm the parameter settings on both copy-source and copy-destination inverters before using the copy-destination SJ700 series. After copying the data, be sure to power off and on again to reflect the copied data. (3) Option boards You can use the option boards (SJ-FB, SJ-DG, SJ-DN, SJ-LW, and SJ-PBT) mounted in the SJ300 series for the SJ700 series. To mount the option boards in the SJ700 series, follow the same mounting procedure as that used for the SJ300 series. For details, refer to the instruction manual for each option board. Precaution: Since the SJ700 series has many new functions and additional parameters, some functions of the SJ-DN, SJ-LW, and SJ-PBT (option boards conforming to the open network specifications) cannot be implemented on the SJ700 series. A - 2
Index A B C a/b............................................................4-48, 4-62 absolute position control ......................4-107, 4-108 acceleration/deceleration patterns ....................4-31 acceleration curve constant ..............................4-31 acceleration time......................................4-10, 4-30 acceleration (2) time .........................................4-30 acceleration stop...............................................4-25 actual-frequency monitoring.......................4-3, 4-98 ADD ..................................................................4-14 AHD ..................................................................4-60 AL .....................................................................4-61 alarm code output .............................................4-66 alarm relay terminal function.............................4-62 allowable under-voltage power failure time .............................................................4-33 AM .............................................................2-7, 4-75 AMI ............................................................2-7, 4-75 analog command holding..................................4-60 analog input filter...............................................4-15 ascii mode....................................................... 4-117 AT ..............................................................2-7, 4-12 ATR...................................................................4-99 automatic carrier frequency reduction...............4-45 automatic torque boost .....................................4-19 AVR................................................................... 4-11 AVR voltage select...................................4-11, 4-15 basic display .....................................................4-77 base frequency ................................................. 4-11 BER ..................................................................4-82 binary operation .......................................4-48, 4-49 bit operation .............................................4-48, 4-49 BOK ..................................................................4-82 braking control ..................................................4-82 BRD .........................................................2-12, 4-46 BRD load factor monitoring.................................4-6 BRK ..................................................................4-82 capacitor life warning ........................................4-68 carrier frequency...............................................4-44 CAS ..................................................................4-59 CE ...................................................................2-19 CF1, CF2, CF3, CF4.........................................4-48 CM1 ...........................................................2-7, 2-21 commercial power supply switching..................4-54 communication function .........................4-68, 4-114 communication line disconnection signal...........................................................4-68 constant-torque characteristic (electronic thermal)......................................4-37 constant-torque characteristic (VC)..........4-16, 4-89 control circuit terminal .........................................2-7 control gain switching........................................4-59 control mode .....................................................4-16 cooling-fan operation ...............................4-46, 4-69 cooling-fan speed drop signal ...........................4-69 copying .........................................4-95, Appendix-1 counterrotation prevention ................................4-92 CP1, CP2, CP3...............................................4-109 CS.....................................................................4-54 cumulative power monitoring ..............................4-4 D E F Index - 1 cumulative power-on time monitoring ........ 4-4, 4-65 cumulative running time...................................... 4-4 current position monitor ...................................... 4-5 2CH .................................................................. 4-30 data comparison display................................... 4-77 DB .................................................................... 4-20 DC braking ....................................................... 4-20 DC voltage monitoring ........................................ 4-6 deceleration (2) time setting ............................. 4-30 deceleration and stopping at power failure.......................................................... 4-85 deceleration curve constant.............................. 4-32 deceleration overvoltage restraint..................... 4-42 deceleration time .............................................. 4-10 derating ............................................................ 4-44 detection of terminal disconnection .................. 4-72 digital operator........................................... 2-22, 3-3 display of trip monitoring.............................. 4-6, 5-9 DSE .................................................................. 4-97 DWN................................................................. 4-57 easy sequence .......................................... 4-5, 4-96 electronic gear..................................... 4-100, 4-102 electronic thermal ............................................. 4-37 electronic thermal overload monitoring............... 4-6 electronic thermal warning level setting............ 4-39 EMC ............................................safety instructions emergency stop.................................................. 2-9 EMR ................................................................... 2-9 encoder pulse......................................... 4-97,4-104 end frequency......................................... 4-14,4-105 end-frequency rate ........................................... 4-15 energy-saver operation..................................... 4-32 excessive speed................................................. 5-5 extended function mode ..................................... 3-8 external analog input ........................................ 4-12 external DC braking.......................................... 4-20 external thermistor............................................ 4-73 external trip....................................................... 4-58 F/R.................................................................... 4-58 F-TM................................................................. 4-52 factory default(setting) .................................... 4-76 FA1, FA2, FA3, FA4, FA5.................................. 4-63 FBV ......................................................... 4-26, 4-29 feedback.................................................... 4-1, 4-28 feedback option ................................................ 4-97 feed forward selection ...................................... 4-28 FM ............................................................. 2-7, 4-74 FOC.................................................................. 4-92 forcible operation.............................................. 4-52 forcible-terminal operation ................................ 4-52 forcing............................................................... 4-92 forward rotation signal ...................................... 4-70 FOT .................................................................4-111 FR..................................................................... 4-69 free setting of electronic thermal characteristic............................................... 4-38 free V/f characteristic........................................ 4-17 free-run stop .............................................. 4-9, 4-53
Page 1 and 2:
HITACHI INVERTER SJ700-2 SERIES INS
Page 3 and 4:
Safety Instructions Safety Instruct
Page 5 and 6:
Safety Instructions 3. Operation !
Page 7 and 8:
Safety Instructions Precautions Con
Page 9 and 10:
Safety Instructions Precautions Con
Page 11 and 12:
Safety Instructions 10. Distributio
Page 13 and 14:
Contents Chapter 1 Overview 1.1 Ins
Page 15 and 16:
Contents 4.2.30 Overload restrictio
Page 17 and 18:
Contents 4.3.15 Speed/position swit
Page 19:
Chapter 1 Overview This chapter des
Page 22 and 23:
Chapter 1 Overview 1.2 Method of In
Page 24:
Chapter 2 Installation and Wiring T
Page 27 and 28:
Chapter 2 Installation and Wiring 2
Page 29 and 30:
Page 31 and 32:
Page 33 and 34:
Chapter 2 Installation and Wiring D
Page 35 and 36:
Chapter 2 Installation and Wiring S
Page 37 and 38:
Chapter 2 Installation and Wiring c
Page 39 and 40:
Page 41 and 42:
Page 43 and 44:
Chapter 2 Installation and Wiring (
Page 45 and 46:
Page 47 and 48:
Chapter 2 Installation and Wiring (
Page 49:
Chapter 3 Operation This chapter de
Page 52 and 53:
Chapter 3 Operation You can operate
Page 54 and 55:
Chapter 3 Operation 3.2.2 Code disp
Page 56 and 57:
Chapter 3 Operation Key operation a
Page 58 and 59:
Chapter 3 Operation (3) Code/data d
Page 60 and 61:
Chapter 3 Operation 3.3 How To Make
Page 62 and 63:
Chapter 3 Operation ELB 3-phase pow
Page 65 and 66:
Chapter 4 Explanation of Functions
Page 67 and 68:
Page 69 and 70:
Page 71 and 72:
Page 73 and 74:
Page 75 and 76:
Page 77 and 78:
Page 79 and 80:
Page 81 and 82:
Page 83 and 84:
Page 85 and 86:
Page 87 and 88:
Page 89 and 90:
Page 91 and 92:
Page 93 and 94:
Page 95 and 96:
Page 97 and 98:
Page 99 and 100:
Page 101 and 102:
Page 103 and 104:
Page 105 and 106:
Page 107 and 108:
Page 109 and 110:
Page 111 and 112:
Page 113 and 114:
Page 115 and 116:
Page 117 and 118:
Page 119 and 120:
Page 121 and 122:
Page 123 and 124:
Page 125 and 126:
Page 127 and 128:
Page 129 and 130:
Page 131 and 132:
Page 133 and 134:
Page 135 and 136:
Page 137 and 138:
Page 139 and 140:
Page 141 and 142:
Page 143 and 144:
Page 145 and 146:
Page 147 and 148:
Page 149 and 150:
Voltage across main circuit termina
Page 151 and 152:
Page 153 and 154:
Page 155 and 156:
Page 157 and 158:
Page 159 and 160:
Page 161 and 162:
Page 163 and 164:
Page 165 and 166:
Page 167 and 168:
Page 169 and 170:
Page 171 and 172:
Page 173 and 174:
Page 175 and 176:
Page 177 and 178:
Page 179 and 180:
Page 181 and 182:
Page 183 and 184:
Page 185 and 186:
Page 187 and 188:
Page 189 and 190:
Page 191 and 192:
Page 193 and 194:
Page 195 and 196:
Page 197 and 198:
Page 199 and 200:
Page 201 and 202:
Page 203 and 204:
Page 205 and 206:
Page 207 and 208:
Page 209 and 210:
Page 211 and 212:
Page 213 and 214:
Page 215 and 216:
Page 217 and 218:
Page 219 and 220:
Page 221 and 222:
Page 223 and 224:
Page 225 and 226:
Page 227 and 228: Chapter 4 Explanation of Functions
Page 230 and 231: Chapter 5 Error Codes 5.1 Error Cod
Page 232 and 233: Chapter 5 Error Codes Name Gate arr
Page 234 and 235: Chapter 5 Error Codes 5.1.2 Option
Page 236 and 237: Chapter 5 Error Codes 3) Error indi
Page 238 and 239: Chapter 5 Error Codes 5.1.3 Trip co
Page 240: Chapter 6 Maintenance and Inspectio
Page 243 and 244: Chapter 6 Maintenance and Inspectio
Page 250 and 251: Chapter 7 Specifications 7.1 Specif
Page 252 and 253: Chapter 7 Specifications (3) Common
Page 254 and 255: Chapter 7 Specifications SJ700-150
Page 256 and 257: Chapter 7 Specifications SJ700-750
Page 259 and 260: Chapter 8 List of Data Settings 8.1
Page 261 and 262: Chapter 8 List of Data Settings 8.4
Page 263 and 264: Chapter 8 List of Data Settings AVR
Page 265 and 266: Chapter 8 List of Data Settings Oth
Page 267 and 268: Chapter 8 List of Data Settings Cod
Page 277: Appendix Upgrading from the SJ300 S
Page 281 and 282: Index O P O........................
show all

SJ700-2 Instruction Manual NT204DX - Hitachi America, Ltd.

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?