SJ700-2 Instruction Manual NT204DX - Hitachi America, Ltd.
SJ700-2 Instruction Manual NT204DX - Hitachi America, Ltd. SJ700-2 Instruction Manual NT204DX - Hitachi America, Ltd.
Chapter 8 List of Data Settings Code Function name Monitored data or setting Default _FF _FEF _FUF Setting during operation (allowed or not) Change during operation (allowed or not) Page User parameters U001 User-selected function 1 no/d001 to P131 no ◦ ◦ U002 User-selected function 2 no/d001 to P131 no ◦ ◦ U003 User-selected function 3 no/d001 to P131 no ◦ ◦ U004 User-selected function 4 no/d001 to P131 no ◦ ◦ U005 User-selected function 5 no/d001 to P131 no ◦ ◦ U006 User-selected function 6 no/d001 to P131 no ◦ ◦ U007 User-selected function 7 no/d001 to P131 no ◦ ◦ U008 User-selected function 8 no/d001 to P131 no ◦ ◦ U009 User-selected function 9 no/d001 to P131 no ◦ ◦ U010 User-selected function 10 no/d001 to P131 no ◦ ◦ U011 User-selected function 11 no/d001 to P131 no ◦ ◦ U012 User-selected function 12 no/d001 to P131 no ◦ ◦ 4-76 8 - 18
Appendix Upgrading from the SJ300 Series The SJ300 series inverter is upwardly compatible with the SJ700 series inverter. Therefore, you can: - mount the control circuit terminal block board of the SJ300 series in the SJ700 series without removing the connected cables, - copy the parameter settings from the SJ300 series into the SJ700 series, and - use the option boards mounted in the SJ300 series for the SJ700 series without removing the connected cables. (1) Control circuit terminal block board You can mount the control circuit terminal block board of the SJ300 series into the SJ700 series. Note, however, that the backing plate is incompatible. (Procedure for replacing the control circuit terminal block board) As shown in the figure on the right, the fixing screw locations on the control circuit terminal block board are common to the SJ300 and SJ700 series. To remove and install the control circuit terminal block board, follow the steps 1) to 5) described below. Control circuit terminal block board mounted in the SJ300/SJ700 series (front view) Fixing screw (M3) x 2 Board guide pin Fixing screw Connector (60 poles) Board guide pin x 2 Board guide pin Fixing screw Precautions: Use care to prevent the control circuit terminal block board from twisting when removing or mounting it. Otherwise, the board guide pins and connector pins may be damaged. Do not pull the cables connected to the control circuit terminal block board when you remove the board from the SJ300 series. Do not forcibly insert the board into the mounting slot. Make sure that the board is correctly fitted onto the board guide pins and the connectors are correctly fitted to each other. SJ300 series SJ700 series Removing the control circuit terminal block board from the SJ300 series 1) Remove two fixing screws from the control circuit terminal block board. 2) Pull the control circuit terminal block board straight toward you to remove it from the SJ300 series. Precautions: Pull out the board slowly. Be careful not to bend the connector pins. Be careful not to break the board guide pins. Mounting the removed control circuit terminal block board in the SJ700 series 3) Remove the original control circuit terminal block board from the SJ700 series beforehand (as instructed in steps 1) and 2)). 4) Insert the control circuit terminal block board removed from the SJ300 series straight into the slot along the board guide pins and connector pins until it touches the fixing-screw seats. Precautions: Push in the board slowly. Be careful not to bend the connector pins. Be careful not to break the board guide pins. 5) Secure the control circuit terminal block board with two fixing screws. Precaution: Be sure to fix the board with the two fixing screws. A - 1
- Page 225 and 226: Chapter 4 Explanation of Functions
- Page 227 and 228: Chapter 4 Explanation of Functions
- Page 230 and 231: Chapter 5 Error Codes 5.1 Error Cod
- Page 232 and 233: Chapter 5 Error Codes Name Gate arr
- Page 234 and 235: Chapter 5 Error Codes 5.1.2 Option
- Page 236 and 237: Chapter 5 Error Codes 3) Error indi
- Page 238 and 239: Chapter 5 Error Codes 5.1.3 Trip co
- Page 240: Chapter 6 Maintenance and Inspectio
- Page 243 and 244: Chapter 6 Maintenance and Inspectio
- Page 245 and 246: Chapter 6 Maintenance and Inspectio
- Page 247 and 248: Chapter 6 Maintenance and Inspectio
- Page 250 and 251: Chapter 7 Specifications 7.1 Specif
- Page 252 and 253: Chapter 7 Specifications (3) Common
- Page 254 and 255: Chapter 7 Specifications SJ700-150
- Page 256 and 257: Chapter 7 Specifications SJ700-750
- Page 259 and 260: Chapter 8 List of Data Settings 8.1
- Page 261 and 262: Chapter 8 List of Data Settings 8.4
- Page 263 and 264: Chapter 8 List of Data Settings AVR
- Page 265 and 266: Chapter 8 List of Data Settings Oth
- Page 267 and 268: Chapter 8 List of Data Settings Cod
- Page 269 and 270: Chapter 8 List of Data Settings Cod
- Page 271 and 272: Chapter 8 List of Data Settings Cod
- Page 273 and 274: Chapter 8 List of Data Settings Cod
- Page 275: Chapter 8 List of Data Settings Cod
- Page 279 and 280: Index A B C a/b....................
- Page 281 and 282: Index O P O........................
Chapter 8 List of Data Settings<br />
Code Function name Monitored data or setting<br />
Default<br />
_FF _FEF _FUF<br />
Setting<br />
during<br />
operation<br />
(allowed or<br />
not)<br />
Change<br />
during<br />
operation<br />
(allowed or<br />
not)<br />
Page<br />
User parameters<br />
U001 User-selected function 1 no/d001 to P131 no ◦ ◦<br />
U002 User-selected function 2 no/d001 to P131 no ◦ ◦<br />
U003 User-selected function 3 no/d001 to P131 no ◦ ◦<br />
U004 User-selected function 4 no/d001 to P131 no ◦ ◦<br />
U005 User-selected function 5 no/d001 to P131 no ◦ ◦<br />
U006 User-selected function 6 no/d001 to P131 no ◦ ◦<br />
U007 User-selected function 7 no/d001 to P131 no ◦ ◦<br />
U008 User-selected function 8 no/d001 to P131 no ◦ ◦<br />
U009 User-selected function 9 no/d001 to P131 no ◦ ◦<br />
U010 User-selected function 10 no/d001 to P131 no ◦ ◦<br />
U011 User-selected function 11 no/d001 to P131 no ◦ ◦<br />
U012 User-selected function 12 no/d001 to P131 no ◦ ◦<br />
4-76<br />
8 - 18