SJ700-2 Instruction Manual NT204DX - Hitachi America, Ltd.

More documents

Recommendations

Info

Chapter 8 List of Data Settings Code Function name Monitored data or setting Default _FF _FEF _FUF Setting during operation (allowed or not) Change during operation (allowed or not) Page Intelligent output terminals Analog monitoring Intelligent output terminals C021 Terminal [11] function 00 (RUN: running), 01 (FA1: constant-speed reached), 02 (FA2: set 01 ◦ C022 Terminal [12] function frequency overreached), 03 (OL: overload notice advance signal (1)), 04 (OD: output deviation for PID control), 05 (AL: alarm signal), 06 (FA3: set 00 ◦ C023 Terminal [13] function frequency reached), 07 (OTQ: over-torque), 08 (IP: instantaneous power 03 ◦ C024 Terminal [14] function failure), 09 (UV: undervoltage), 10 (TRQ: torque limited), 11 (RNT: operation time over), 12 (ONT: plug-in time over), 13 (THM: thermal alarm 07 ◦ C025 Terminal [15] function signal), 19 (BRK: brake release), 20 (BER: braking error), 21 (ZS: 0 Hz 40 ◦ detection signal), 22 (DSE: speed deviation maximum), 23 (POK: positioning completed), 24 (FA4: set frequency overreached 2), 25 (FA5: set frequency reached 2), 26 (OL2: overload notice advance signal (2)), 27 (Odc: Analog O disconnection detection), 28 (OIDc: Analog OI disconnection detection), 29 (O2Dc: Analog O2 disconnection detection), 31 (FBV: PID feedback comparison), 32 (NDc: communication line disconnection), 33 (LOG1: logical operation result 1), 34 (LOG2: logical operation result 2), 35 (LOG3: logical operation result 3), 36 (LOG4: logical operation result 4), 37 (LOG5: logical operation result 5), 38 (LOG6: logical operation result 6), 39 (WAC: capacitor life warning), 40 (WAF: cooling-fan C026 Alarm relay terminal function speed drop), 41 (FR: starting contact signal), 42 (OHF: heat sink overheat 05 ◦ warning), 43 (LOC: low-current indication signal), 44 (M01: general-purpose output 1), 45 (M02: general-purpose output 2), 46 (M03: general-purpose output 3), 47 (M04: general-purpose output 4), 48 (M05: general-purpose output 5), 49 (M06: general-purpose output 6), 50 (IRDY: inverter ready), 51 (FWR: forward rotation), 52 (RVR: reverse rotation), 53 (MJA: major failure), 54(WCO: window comparator O), 55(WCOI: window comparator OI), 56 (WCO2: window comparator O2) (When alarm code output is selected for "C062", functions "AC0" to "AC2" or "AC0" to "AC3" [ACn: alarm code output] are forcibly assigned to intelligent output terminals 11 to 13 or 11 to 14, respectively.) C027 C028 C029 C030 [FM] siginal selection [AM] siginal selection [AMI] siginal selection Digital current monitor reference value 00 (output frequency), 01 (output current), 02 (output torque), 03 (digital output frequency), 04 (output voltage), 05 (input power), 06 (electronic thermal overload), 07 (LAD frequency), 08 (digital current monitoring), 09 (motor temperature), 10 (heat sink temperature), 12 (general-purpose output YA0) 00 (output frequency), 01 (output current), 02 (output torque), 04 (output voltage), 05 (input power), 06 (electronic thermal overload), 07 (LAD frequency), 09 (motor temperature), 10 (heat sink temperature), 11 (output torque [signed value]), 13 (general-purpose output YA1) 00 (output frequency), 01 (output current), 02 (output torque), 04 (output voltage), 05 (input power), 06 (electronic thermal overload), 07 (LAD frequency), 09 (motor temperature), 10 (heat sink temperature), 14 (general-purpose output YA2) 0.20 x "rated current" to 2.00 x "rated current" (A) (Current with digital current monitor output at 1,440 Hz) 4-60 00 ◦ 4-73 00 ◦ 00 ◦ 4-74 Rated current of inverter ◦ ◦ 4-73 C031 Terminal [11] active state 00 (NO) / 01 (NC) 00 ◦ C032 Terminal [12] active state 00 (NO) / 01 (NC) 00 ◦ C033 Terminal [13] active state 00 (NO) / 01 (NC) 00 ◦ C034 Terminal [14] active state 00 (NO) / 01 (NC) 00 ◦ C035 Terminal [15] active state 00 (NO) / 01 (NC) 00 ◦ C036 Alarm relay active state 00 (NO) / 01 (NC) 01 ◦ 4-61 8 - 10
Chapter 8 List of Data Settings Code Function name Monitored data or setting Default _FF _FEF _FUF Setting during operation (allowed or not) Change during operation (allowed or not) Page Levels and output terminal status Communication function Adjustment Others Meter adjustment C038 C039 C040 Low-current indication signal output mode selection Low-current indication signal detection level Overload signal output mode 00 (output during acceleration/deceleration and constant-speed operation), 01 (output only during constant-speed operation) 01 ◦ 0.0 to 2.00 x "rated current" (A) Rated current of inverter ◦ ◦ 00 (output during acceleration/deceleration and constant-speed operation), 01 (output only during constant-speed operation) 01 ◦ C041 Overload level setting 0.0 to 2.00 x "rated current" (A) Rated current of inverter ◦ ◦ C042 Frequency arrival setting for accel. 0.00 to 99.99, 100.0 to 400.0 (Hz) 0.00 ◦ C043 Frequency arrival setting for decel. 0.00 to 99.99, 100.0 to 400.0 (Hz) 0.00 ◦ C044 PID deviation level setting 0.0 to 100.0 (%) 3.0 ◦ 4-29 C045 C046 Frequency arrival setting for acceleration (2) Frequency arrival setting for deceleration (2) 0.00 to 99.99, 100.0 to 400.0 (Hz) 0.00 ◦ 0.00 to 99.99, 100.0 to 400.0 (Hz) 0.00 ◦ C052 Maximum PID feedback data 0.0 to 100.0 (%) 100.0 ◦ C053 Minimum PID feedback data 0.0 to 100.0 (%) 0.0 ◦ C055 C056 C057 C058 C061 Over-torque (forward-driving) level setting Over-torque (reverse regenerating) level setting Over-torque (reverse driving) level setting Over-torque (forward regenerating) level setting Electronic thermal warning level setting 0. to 200. (%) 100. ◦ 0. to 200. (%) 100. ◦ 0. to 200. (%) 100. ◦ 0. to 200. (%) 100. ◦ 0. to 100. (%) 80. ◦ 4-38 C062 Alarm code output 00 (disabling), 01 (3 bits), 02 (4 bits) 00 ◦ 4-65 C063 Zero speed detection level 0.00 to 99.99, 100.0 (Hz) 0.00 ◦ 4-64 C064 Heat sink overheat warning level 0. to 200.0 (°C) 120. ◦ 4-68 C071 Communication speed selection 02 (loopback test), 03 (2,400 bps), 04 (4,800 bps), 05 (9,600 bps), 06 (19,200 bps) 04 ◦ C072 Node allocation 1. to 32. 1. ◦ C073 Communication data length selection 7 (7 bits), 8 (8 bits) 7 ◦ C074 Communication parity selection 00 (no parity), 01 (even parity), 02 (odd parity) 00 ◦ C075 Communication stop bit selection 1 (1 bit), 2 (2 bits) 1 ◦ C076 C077 Selection of the operation after communication error Communication timeout limit before tripping 00 (tripping), 01 (tripping after decelerating and stopping the motor), 02 (ignoring errors), 03 (stopping the motor after free-running), 04 (decelerating and stopping the motor) 02 ◦ 0.00 to 99.99 (s) 0.00 ◦ C078 Communication wait time 0. to 1000. (ms) 0. ◦ C079 Communication mode selection 00(ASCII), 01(Modbus-RTU) 00 ◦ C081 [O] input span calibration 0. to 9999., 1000 to 6553(10000 to 65530) Factory setting ◦ ◦ C082 [OI] input span calibration 0. to 9999., 1000 to 6553(10000 to 65530) Factory setting ◦ ◦ C083 [O2] input span calibration 0. to 9999., 1000 to 6553(10000 to 65530) Factory setting ◦ ◦ C085 Thermistor input tuning 0.0 to 999.9, 1000. Factory setting ◦ ◦ 4-72 C091 Debug mode enable (Do not change this parameter, which is intended for factory adjustment.) 00 − C101 Up/Down memory mode selection 00 (not storing the frequency data), 01 (storing the frequency data) 00 ◦ 4-56 C102 C103 Reset mode selection Restart mode after reset 00 (resetting the trip when RS is on), 01 (resetting the trip when RS is off), 02 (enabling resetting only upon tripping [resetting when RS is on]), 03(resetting only trip) 00 (starting with 0 Hz), 01 (starting with matching frequency), 02 (restarting with active matching frequency) 00 ◦ ◦ 00 ◦ C105 FM gain adjustment 50. to 200. (%) 100. ◦ ◦ 4-73 C106 AM gain adjustment 50. to 200. (%) 100. ◦ ◦ C107 AMI gain adjustment 50. to 200. (%) 100. ◦ ◦ C109 AM bias adjustment 0. to 100. (%) 0. ◦ ◦ C110 AMI bias adjustment 0. to 100. (%) 20. ◦ ◦ (Note)indicate the setting range of 75 to 150kW 4-69 4-40 4-62 4-62 4-29 4-65 4-113 − 4-54 4-74 8 - 11
Page 1 and 2:
HITACHI INVERTER SJ700-2 SERIES INS
Page 3 and 4:
Safety Instructions Safety Instruct
Page 5 and 6:
Safety Instructions 3. Operation !
Page 7 and 8:
Safety Instructions Precautions Con
Page 9 and 10:
Safety Instructions Precautions Con
Page 11 and 12:
Safety Instructions 10. Distributio
Page 13 and 14:
Contents Chapter 1 Overview 1.1 Ins
Page 15 and 16:
Contents 4.2.30 Overload restrictio
Page 17 and 18:
Contents 4.3.15 Speed/position swit
Page 19:
Chapter 1 Overview This chapter des
Page 22 and 23:
Chapter 1 Overview 1.2 Method of In
Page 24:
Chapter 2 Installation and Wiring T
Page 27 and 28:
Chapter 2 Installation and Wiring 2
Page 29 and 30:
Page 31 and 32:
Page 33 and 34:
Chapter 2 Installation and Wiring D
Page 35 and 36:
Chapter 2 Installation and Wiring S
Page 37 and 38:
Chapter 2 Installation and Wiring c
Page 39 and 40:
Page 41 and 42:
Page 43 and 44:
Chapter 2 Installation and Wiring (
Page 45 and 46:
Page 47 and 48:
Chapter 2 Installation and Wiring (
Page 49:
Chapter 3 Operation This chapter de
Page 52 and 53:
Chapter 3 Operation You can operate
Page 54 and 55:
Chapter 3 Operation 3.2.2 Code disp
Page 56 and 57:
Chapter 3 Operation Key operation a
Page 58 and 59:
Chapter 3 Operation (3) Code/data d
Page 60 and 61:
Chapter 3 Operation 3.3 How To Make
Page 62 and 63:
Chapter 3 Operation ELB 3-phase pow
Page 65 and 66:
Chapter 4 Explanation of Functions
Page 67 and 68:
Page 69 and 70:
Page 71 and 72:
Page 73 and 74:
Page 75 and 76:
Page 77 and 78:
Page 79 and 80:
Page 81 and 82:
Page 83 and 84:
Page 85 and 86:
Page 87 and 88:
Page 89 and 90:
Page 91 and 92:
Page 93 and 94:
Page 95 and 96:
Page 97 and 98:
Page 99 and 100:
Page 101 and 102:
Page 103 and 104:
Page 105 and 106:
Page 107 and 108:
Page 109 and 110:
Page 111 and 112:
Page 113 and 114:
Page 115 and 116:
Page 117 and 118:
Page 119 and 120:
Page 121 and 122:
Page 123 and 124:
Page 125 and 126:
Page 127 and 128:
Page 129 and 130:
Page 131 and 132:
Page 133 and 134:
Page 135 and 136:
Page 137 and 138:
Page 139 and 140:
Page 141 and 142:
Page 143 and 144:
Page 145 and 146:
Page 147 and 148:
Page 149 and 150:
Voltage across main circuit termina
Page 151 and 152:
Page 153 and 154:
Page 155 and 156:
Page 157 and 158:
Page 159 and 160:
Page 161 and 162:
Page 163 and 164:
Page 165 and 166:
Page 167 and 168:
Page 169 and 170:
Page 171 and 172:
Page 173 and 174:
Page 175 and 176:
Page 177 and 178:
Page 179 and 180:
Page 181 and 182:
Page 183 and 184:
Page 185 and 186:
Page 187 and 188:
Page 189 and 190:
Page 191 and 192:
Page 193 and 194:
Page 195 and 196:
Page 197 and 198:
Page 199 and 200:
Page 201 and 202:
Page 203 and 204:
Page 205 and 206:
Page 207 and 208:
Page 209 and 210:
Page 211 and 212:
Page 213 and 214:
Page 215 and 216:
Page 217 and 218: Chapter 4 Explanation of Functions
Page 230 and 231: Chapter 5 Error Codes 5.1 Error Cod
Page 232 and 233: Chapter 5 Error Codes Name Gate arr
Page 234 and 235: Chapter 5 Error Codes 5.1.2 Option
Page 236 and 237: Chapter 5 Error Codes 3) Error indi
Page 238 and 239: Chapter 5 Error Codes 5.1.3 Trip co
Page 240: Chapter 6 Maintenance and Inspectio
Page 243 and 244: Chapter 6 Maintenance and Inspectio
Page 250 and 251: Chapter 7 Specifications 7.1 Specif
Page 252 and 253: Chapter 7 Specifications (3) Common
Page 254 and 255: Chapter 7 Specifications SJ700-150
Page 256 and 257: Chapter 7 Specifications SJ700-750
Page 259 and 260: Chapter 8 List of Data Settings 8.1
Page 261 and 262: Chapter 8 List of Data Settings 8.4
Page 263 and 264: Chapter 8 List of Data Settings AVR
Page 265 and 266: Chapter 8 List of Data Settings Oth
Page 267: Chapter 8 List of Data Settings Cod
Page 271 and 272: Chapter 8 List of Data Settings Cod
Page 277 and 278: Appendix Upgrading from the SJ300 S
Page 279 and 280: Index A B C a/b....................
Page 281 and 282: Index O P O........................
show all

SJ700-2 Instruction Manual NT204DX - Hitachi America, Ltd.

Create successful ePaper yourself

Delete template?

Save as template?