SJ700-2 Instruction Manual NT204DX - Hitachi America, Ltd.

More documents

Recommendations

Info

Chapter 4 Explanation of Functions (6) List of registers The "R/W" column of the list indicates whether the coils and registers are read-only or readable and writable. "R" indicates a read-only coil or register. "R/W" indicates a readable and writable coil or register. (i) List of coils Coil No. Item R/W Setting 0000h (Reserved) - 0001h Operation command R/W 1: Run, 0: Stop (valid when A002 = 03) 0002h Rotation direction command R/W 1: Reverse rotation, 0: Forward rotation (valid when A002 = 03) 0003h External trip (EXT) R/W 1: Trip 0004h Trip reset (RS) R/W 1: Reset 0005h (Reserved) - 0006h (Reserved) - 0007h Intelligent input terminal [1] R/W 1: ON, 0: OFF (*1) 0008h Intelligent input terminal [2] R/W 1: ON, 0: OFF (*1) 0009h Intelligent input terminal [3] R/W 1: ON, 0: OFF (*1) 000Ah Intelligent input terminal [4] R/W 1: ON, 0: OFF (*1) 000Bh Intelligent input terminal [5] R/W 1: ON, 0: OFF (*1) 000Ch Intelligent input terminal [6] R/W 1: ON, 0: OFF (*1) 000Dh Intelligent input terminal [7] R/W 1: ON, 0: OFF (*1) 000Eh Intelligent input terminal [8] R/W 1: ON, 0: OFF (*1) 000Fh Operation status R 1: Run, 0: Stop (interlocked to "d003") 0010h Rotation direction R 1: Reverse rotation, 0: Forward rotation (interlocked to "d003") 0011h Inverter ready R 1: Ready, 0: Not ready 0012h Unused R 0013h RUN (running) R 1: Tripping, 0: Normal 0014h FA1 (constant-speed reached) R 1: ON, 0: OFF 0015h FA2 (set frequency overreached) R 1: ON, 0: OFF 0016h OL (overload notice advance signal (1)) R 1: ON, 0: OFF 0017h OD (output deviation for PID control) R 1: ON, 0: OFF 0018h AL (alarm signal) R 1: ON, 0: OFF 0019h FA3 (set frequency reached) R 1: ON, 0: OFF 001Ah OTQ (over-torque) R 1: ON, 0: OFF 001Bh IP (instantaneous power failure) R 1: ON, 0: OFF 001Ch UV (undervoltage) R 1: ON, 0: OFF 001Dh TRQ (torque limited) R 1: ON, 0: OFF 001Eh RNT (operation time over) R 1: ON, 0: OFF 001Fh ONT (plug-in time over) R 1: ON, 0: OFF 0020h THM (thermal alarm signal) R 1: ON, 0: OFF 0021h (Reserved) - 0022h (Reserved) - 0023h (Reserved) - 0024h (Reserved) - 0025h (Reserved) - 0026h BRK (brake release) R 1: ON, 0: OFF 0027h BER (brake error) R 1: ON, 0: OFF 0028h ZS (0 Hz detection signal) R 1: ON, 0: OFF 0029h DSE (speed deviation maximum) R 1: ON, 0: OFF 002Ah POK (positioning completed) R 1: ON, 0: OFF 002Bh FA4 (set frequency overreached 2) R 1: ON, 0: OFF 002Ch FA5 (set frequency reached 2) R 1: ON, 0: OFF 002Dh OL2 (overload notice advance signal (2)) R 1: ON, 0: OFF 002Eh Odc: Analog O disconnection detection - 002Fh OIDc: Analog OI disconnection detection - 0030h O2Dc: Analog O2 disconnection detection - 0031h (Reserved) - 0032h FBV (PID feedback comparison) R 1: ON, 0: OFF 0033h NDc (communication train disconnection) R 1: ON, 0: OFF 0034h LOG1 (logical operation result 1) R 1: ON, 0: OFF 4 - 140
Chapter 4 Explanation of Functions Coil No. Item R/W Setting 0035h LOG2 (logical operation result 2) R 1: ON, 0: OFF 0036h LOG3 (logical operation result 3) R 1: ON, 0: OFF 0037h LOG4 (logical operation result 4) R 1: ON, 0: OFF 0038h LOG5 (logical operation result 5) R 1: ON, 0: OFF 0039h LOG6 (logical operation result 6) R 1: ON, 0: OFF 003Ah WAC (capacitor life warning) R 1: ON, 0: OFF 003Bh WAF (cooling-fan speed drop) R 1: ON, 0: OFF 003Ch FR (starting contact signal) R 1: ON, 0: OFF 003Dh OHF (heat sink overheat warning) R 1: ON, 0: OFF 003Eh LOC (low-current indication signal) R 1: ON, 0: OFF 003Fh M01 (general output 1) R 1: ON, 0: OFF 0040h M02 (general output 2) R 1: ON, 0: OFF 0041h M03 (general output 3) R 1: ON, 0: OFF 0042h M04 (general output 4) R 1: ON, 0: OFF 0043h M05 (general output 5) R 1: ON, 0: OFF 0044h M06 (general output 6) R 1: ON, 0: OFF 0045h IRDY (inverter ready) R 1: ON, 0: OFF 0046h FWR (forward rotation) R 1: ON, 0: OFF 0047h RVR (reverse rotation) R 1: ON, 0: OFF 0048h MJA (major failure) R 1: ON, 0: OFF 0049h Data writing in progress R 1: Writing in progress, 0: Normal status 004Ah CRC error R 1: Error detected, 0: No error (*2) 004Bh Overrun R 1: Error detected, 0: No error (*2) 004Ch Framing error R 1: Error detected, 0: No error (*2) 004Dh Parity error R 1: Error detected, 0: No error (*2) 004Eh Sum check error R 1: Error detected, 0: No error (*2) 004Fh (reserved) 0050h WCO (window comparator O) R 1: ON, 0:FF 0051h WCO (window comparator OI) R 1: ON, 0:FF 0052h WCO (window comparator O2) R 1: ON, 0:FF *1 Normally, this coil is turned on when the corresponding intelligent input terminal on the control circuit terminal block is turned on or the coil itself is set to on. In this regard, the operation of the intelligent input terminal has priority over the operation of the coil. If disconnection of the communication train has disabled the master system from turning off the coil, turn the corresponding intelligent input terminal on the control circuit block on and off. This operation turns off the coil. *2 Communication error data is retained until an error reset command is input. (The data can be reset during the inverter operation.) 4 - 141
Page 1 and 2:
HITACHI INVERTER SJ700-2 SERIES INS
Page 3 and 4:
Safety Instructions Safety Instruct
Page 5 and 6:
Safety Instructions 3. Operation !
Page 7 and 8:
Safety Instructions Precautions Con
Page 9 and 10:
Safety Instructions Precautions Con
Page 11 and 12:
Safety Instructions 10. Distributio
Page 13 and 14:
Contents Chapter 1 Overview 1.1 Ins
Page 15 and 16:
Contents 4.2.30 Overload restrictio
Page 17 and 18:
Contents 4.3.15 Speed/position swit
Page 19:
Chapter 1 Overview This chapter des
Page 22 and 23:
Chapter 1 Overview 1.2 Method of In
Page 24:
Chapter 2 Installation and Wiring T
Page 27 and 28:
Chapter 2 Installation and Wiring 2
Page 29 and 30:
Page 31 and 32:
Page 33 and 34:
Chapter 2 Installation and Wiring D
Page 35 and 36:
Chapter 2 Installation and Wiring S
Page 37 and 38:
Chapter 2 Installation and Wiring c
Page 39 and 40:
Page 41 and 42:
Page 43 and 44:
Chapter 2 Installation and Wiring (
Page 45 and 46:
Page 47 and 48:
Chapter 2 Installation and Wiring (
Page 49:
Chapter 3 Operation This chapter de
Page 52 and 53:
Chapter 3 Operation You can operate
Page 54 and 55:
Chapter 3 Operation 3.2.2 Code disp
Page 56 and 57:
Chapter 3 Operation Key operation a
Page 58 and 59:
Chapter 3 Operation (3) Code/data d
Page 60 and 61:
Chapter 3 Operation 3.3 How To Make
Page 62 and 63:
Chapter 3 Operation ELB 3-phase pow
Page 65 and 66:
Chapter 4 Explanation of Functions
Page 67 and 68:
Page 69 and 70:
Page 71 and 72:
Page 73 and 74:
Page 75 and 76:
Page 77 and 78:
Page 79 and 80:
Page 81 and 82:
Page 83 and 84:
Page 85 and 86:
Page 87 and 88:
Page 89 and 90:
Page 91 and 92:
Page 93 and 94:
Page 95 and 96:
Page 97 and 98:
Page 99 and 100:
Page 101 and 102:
Page 103 and 104:
Page 105 and 106:
Page 107 and 108:
Page 109 and 110:
Page 111 and 112:
Page 113 and 114:
Page 115 and 116:
Page 117 and 118:
Page 119 and 120:
Page 121 and 122:
Page 123 and 124:
Page 125 and 126:
Page 127 and 128:
Page 129 and 130:
Page 131 and 132:
Page 133 and 134:
Page 135 and 136:
Page 137 and 138:
Page 139 and 140:
Page 141 and 142:
Page 143 and 144:
Page 145 and 146:
Page 147 and 148:
Page 149 and 150:
Voltage across main circuit termina
Page 151 and 152:
Page 153 and 154: Chapter 4 Explanation of Functions
Page 203: Chapter 4 Explanation of Functions
Page 230 and 231: Chapter 5 Error Codes 5.1 Error Cod
Page 232 and 233: Chapter 5 Error Codes Name Gate arr
Page 234 and 235: Chapter 5 Error Codes 5.1.2 Option
Page 236 and 237: Chapter 5 Error Codes 3) Error indi
Page 238 and 239: Chapter 5 Error Codes 5.1.3 Trip co
Page 240: Chapter 6 Maintenance and Inspectio
Page 243 and 244: Chapter 6 Maintenance and Inspectio
Page 250 and 251: Chapter 7 Specifications 7.1 Specif
Page 252 and 253: Chapter 7 Specifications (3) Common
Page 254 and 255:
Chapter 7 Specifications SJ700-150
Page 256 and 257:
Chapter 7 Specifications SJ700-750
Page 259 and 260:
Chapter 8 List of Data Settings 8.1
Page 261 and 262:
Chapter 8 List of Data Settings 8.4
Page 263 and 264:
Chapter 8 List of Data Settings AVR
Page 265 and 266:
Chapter 8 List of Data Settings Oth
Page 267 and 268:
Chapter 8 List of Data Settings Cod
Page 269 and 270:
Page 271 and 272:
Page 273 and 274:
Page 275 and 276:
Page 277 and 278:
Appendix Upgrading from the SJ300 S
Page 279 and 280:
Index A B C a/b....................
Page 281 and 282:
Index O P O........................
show all

SJ700-2 Instruction Manual NT204DX - Hitachi America, Ltd.

Create successful ePaper yourself

Delete template?

Save as template?