29.01.2015 Views

Table of Contents - The Atmospheric Studies Group at TRC

Table of Contents - The Atmospheric Studies Group at TRC

Table of Contents - The Atmospheric Studies Group at TRC

SHOW MORE
SHOW LESS

Create successful ePaper yourself

Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.

Section 9: CALPUFF<br />

1 ! ZPLTFM = 0. !<br />

1 ! FMFAC = 1. ! !END!<br />

--------<br />

a<br />

D<strong>at</strong>a for each source are tre<strong>at</strong>ed as a separ<strong>at</strong>e input subgroup<br />

and therefore must end with an input group termin<strong>at</strong>or.<br />

SRCNAM is a 12-character name for a source<br />

(No default)<br />

X is an array holding the source d<strong>at</strong>a listed by the column headings<br />

(No default)<br />

SIGYZI is an array holding the initial sigma-y and sigma-z (m)<br />

(Default: 0.,0.)<br />

FMFAC is a vertical momentum flux factor (0. or 1.0) used to represent<br />

the effect <strong>of</strong> rain-caps or other physical configur<strong>at</strong>ions th<strong>at</strong><br />

reduce momentum rise associ<strong>at</strong>ed with the actual exit velocity.<br />

(Default: 1.0 -- full momentum used)<br />

ZPLTFM is the pl<strong>at</strong>form height (m) for sources influenced by an isol<strong>at</strong>ed<br />

structure th<strong>at</strong> has a significant open area between the surface<br />

and the bulk <strong>of</strong> the structure, such as an <strong>of</strong>fshore oil pl<strong>at</strong>form.<br />

<strong>The</strong> Base Elev<strong>at</strong>ion is th<strong>at</strong> <strong>of</strong> the surface (ground or ocean),<br />

and the Stack Height is the release height above the Base (not<br />

above the pl<strong>at</strong>form). Building heights entered in Subgroup 13c<br />

must be those <strong>of</strong> the buildings on the pl<strong>at</strong>form, measured from<br />

the pl<strong>at</strong>form deck. ZPLTFM is used only with MBDW=1 (ISC<br />

downwash method) for sources with building downwash. (Default: 0.0)<br />

b<br />

0. = No building downwash modeled<br />

1. = Downwash modeled for buildings resting on the surface<br />

2. = Downwash modeled for buildings raised above the surface (ZPLTFM > 0.)<br />

NOTE: must be entered as a REAL number (i.e., with decimal point)<br />

c<br />

An emission r<strong>at</strong>e must be entered for every pollutant modeled.<br />

Enter emission r<strong>at</strong>e <strong>of</strong> zero for secondary pollutants th<strong>at</strong> are<br />

modeled, but not emitted. Units are specified by IPTU<br />

(e.g. 1 for g/s).<br />

---------------<br />

Subgroup (13c)<br />

---------------<br />

BUILDING DIMENSION DATA FOR SOURCES SUBJECT TO DOWNWASH<br />

-------------------------------------------------------<br />

Source<br />

a<br />

No. Effective building height, width, length and X/Y <strong>of</strong>fset (in meters)<br />

every 10 degrees. LENGTH, XBADJ, and YBADJ are only needed for<br />

MBDW=2 (PRIME downwash option)<br />

------ ----------------------------------------------------------------<br />

1 ! SRCNAM = BLR1 !<br />

1 ! HEIGHT = 45., 45., 45., 45., 45., 45.,<br />

45., 45., 45., 0., 0., 0.,<br />

0., 0., 0., 0., 0., 0.,<br />

45., 45., 45., 45., 45., 45.,<br />

45., 45., 45., 0., 0., 0.,<br />

0., 0., 0., 0., 0., 0.!<br />

1 ! WIDTH = 12.5, 12.5, 12.5, 12.5, 12.5, 12.5,<br />

12.5, 12.5, 12.5, 0., 0., 0.,<br />

0., 0., 0., 0., 0., 0.,<br />

12.5, 12.5, 12.5, 12.5, 12.5, 12.5,<br />

12.5, 12.5, 12.5, 0., 0., 0.,<br />

0., 0., 0., 0., 0., 0.!<br />

<strong>Table</strong> 9-2 (Continued)<br />

9-36

Hooray! Your file is uploaded and ready to be published.

Saved successfully!

Ooh no, something went wrong!