Table of Contents - The Atmospheric Studies Group at TRC
Table of Contents - The Atmospheric Studies Group at TRC Table of Contents - The Atmospheric Studies Group at TRC
Section 9: CALPUFF -------- a Specify a half life that is greater than or equal to zero for 1 parent species in each block, and set the yield factor for this species to -1 b Specify a yield factor that is greater than or equal to zero for 1 or more child species in each block, and set the half-life for each of these species to -1 NOTE: Assignments in each block are treated as a separate input subgroup and therefore must end with an input group terminator. If NDECAY=0, no assignments and input group terminators should appear. ------------------------------------------------------------------------------- Table 9-2 (Continued) Sample CALPUFF Control File (CALPUFF.INP) Input Group 12 ------------------------------------------------------------------------------- INPUT GROUP: 12 -- Misc. Dispersion and Computational Parameters --------------- Horizontal size of puff (m) beyond which time-dependent dispersion equations (Heffter) are used to determine sigma-y and sigma-z (SYTDEP) Default: 550. ! SYTDEP = 1.0E04 ! Switch for using Heffter equation for sigma z as above (0 = Not use Heffter; 1 = use Heffter (MHFTSZ) Default: 0 ! MHFTSZ = 1 ! Stability class used to determine plume growth rates for puffs above the boundary layer (JSUP) Default: 5 ! JSUP = 5 ! Vertical dispersion constant for stable conditions (k1 in Eqn. 2.7-3) (CONK1) Default: 0.01 ! CONK1 = 0.01 ! Vertical dispersion constant for neutral/ unstable conditions (k2 in Eqn. 2.7-4) (CONK2) Default: 0.1 ! CONK2 = 0.1 ! Factor for determining Transition-point from Schulman-Scire to Huber-Snyder Building Downwash scheme (SS used for Hs < Hb + TBD * HL) (TBD) Default: 0.5 ! TBD = 0.5 ! TBD < 0 ==> always use Huber-Snyder TBD = 1.5 ==> always use Schulman-Scire TBD = 0.5 ==> ISC Transition-point Range of land use categories for which urban dispersion is assumed Default: 10 ! IURB1 = 10 ! (IURB1, IURB2) 19 ! IURB2 = 19 ! Site characterization parameters for single-point Met data files --------- (needed for METFM = 2,3,4) Land use category for modeling domain (ILANDUIN) Default: 20 ! ILANDUIN = 20 ! Roughness length (m) for modeling domain (Z0IN) Default: 0.25 ! Z0IN = 0.25 ! Leaf area index for modeling domain 9-30
Section 9: CALPUFF (XLAIIN) Default: 3.0 ! XLAIIN = 3. ! Elevation above sea level (m) (ELEVIN) Default: 0.0 ! ELEVIN = 0. ! Latitude (degrees) for met location (XLATIN) Default: -999. ! XLATIN = 0. ! Longitude (degrees) for met location (XLONIN) Default: -999. ! XLONIN = 0. ! Specialized information for interpreting single-point Met data files ----- Anemometer height (m) (Used only if METFM = 2,3) (ANEMHT) Default: 10. ! ANEMHT = 10. ! Form of lateral turbulence data in PROFILE.DAT file (Used only if METFM = 4 or MTURBVW = 1 or 3) (ISIGMAV) Default: 1 ! ISIGMAV = 1 ! 0 = read sigma-theta 1 = read sigma-v Choice of mixing heights (Used only if METFM = 4) (IMIXCTDM) Default: 0 ! IMIXCTDM = 0 ! 0 = read PREDICTED mixing heights 1 = read OBSERVED mixing heights Maximum length of a slug (met. grid units) (XMXLEN) Default: 1.0 ! XMXLEN = 1. ! 9-31
- Page 415 and 416: Section 8: CALMET Model Files Table
- Page 417 and 418: Section 8: CALMET Model Files Table
- Page 419 and 420: Section 8: CALMET Model Files Table
- Page 421 and 422: Section 8: CALMET Model Files Table
- Page 423 and 424: Section 8: CALMET Model Files Table
- Page 425 and 426: Section 8: CALMET Model Files -----
- Page 427 and 428: Section 8: CALMET Model Files 6 0 0
- Page 429 and 430: Section 8: CALMET Model Files 3 1 1
- Page 431 and 432: Section 8: CALMET Model Files IBHR
- Page 433 and 434: Section 8: CALMET Model Files Multi
- Page 435 and 436: Section 8: CALMET Model Files Table
- Page 437 and 438: Section 9: CALPUFF 9. CALPUFF The C
- Page 439 and 440: Section 9: CALPUFF The control file
- Page 441 and 442: Section 9: CALPUFF Table 9-1: Input
- Page 443 and 444: Section 9: CALPUFF 17a,b Non-gridde
- Page 445 and 446: Section 9: CALPUFF MASSBAL.DAT outp
- Page 447 and 448: Section 9: CALPUFF d The filenames
- Page 449 and 450: Section 9: CALPUFF >0 = File update
- Page 451 and 452: Section 9: CALPUFF 0 = chemical tra
- Page 453 and 454: Section 9: CALPUFF [DIAGNOSTIC FEAT
- Page 455 and 456: Section 9: CALPUFF ! CSPEC = SO2 !
- Page 457 and 458: Section 9: CALPUFF WGS-84 NAS-C NAR
- Page 459 and 460: Section 9: CALPUFF for selected spe
- Page 461 and 462: Section 9: CALPUFF ---------------
- Page 463 and 464: Section 9: CALPUFF --------- ------
- Page 465: Section 9: CALPUFF Input Group 11 O
- Page 469 and 470: Section 9: CALPUFF Minimum mixing h
- Page 471 and 472: Section 9: CALPUFF Near-Surface dep
- Page 473 and 474: Section 9: CALPUFF Sample CALPUFF C
- Page 475 and 476: Section 9: CALPUFF -------- a Data
- Page 477 and 478: Section 9: CALPUFF Number of buoyan
- Page 479 and 480: Section 9: CALPUFF -------- a Data
- Page 481 and 482: Section 9: CALPUFF Number of non-gr
- Page 483 and 484: Section 9: CALPUFF 9-47
- Page 485 and 486: Section 9: CALPUFF Table 9-3 (Conti
- Page 487 and 488: Section 9: CALPUFF Table 9-3 (Conti
- Page 489 and 490: Section 9: CALPUFF Table 9-3 (Conti
- Page 491 and 492: Section 9: CALPUFF IOUTU IOVERS int
- Page 493 and 494: Section 9: CALPUFF MSHEAR integer V
- Page 495 and 496: Section 9: CALPUFF MDISP integer Me
- Page 497 and 498: Section 9: CALPUFF MPDF integer Pro
- Page 499 and 500: Section 9: CALPUFF 9-63
- Page 501 and 502: Section 9: CALPUFF Table 9-3 (Conti
- Page 503 and 504: Section 9: CALPUFF Table 9-3 (Conti
- Page 505 and 506: Section 9: CALPUFF 9-69
- Page 507 and 508: Section 9: CALPUFF IMFLX integer Co
- Page 509 and 510: Section 9: CALPUFF IPRTU integer Co
- Page 511 and 512: Section 9: CALPUFF Table 9-3 (Conti
- Page 513 and 514: Section 9: CALPUFF Table 9-3 (Conti
- Page 515 and 516: Section 9: CALPUFF Table 9-3 (Conti
Section 9: CALPUFF<br />
--------<br />
a<br />
Specify a half life th<strong>at</strong> is gre<strong>at</strong>er than or equal to zero for 1 parent species<br />
in each block, and set the yield factor for this species to -1<br />
b<br />
Specify a yield factor th<strong>at</strong> is gre<strong>at</strong>er than or equal to zero for 1 or more child<br />
species in each block, and set the half-life for each <strong>of</strong> these species to -1<br />
NOTE: Assignments in each block are tre<strong>at</strong>ed as a separ<strong>at</strong>e input<br />
subgroup and therefore must end with an input group termin<strong>at</strong>or.<br />
If NDECAY=0, no assignments and input group termin<strong>at</strong>ors should appear.<br />
-------------------------------------------------------------------------------<br />
<strong>Table</strong> 9-2 (Continued)<br />
Sample CALPUFF Control File (CALPUFF.INP)<br />
Input <strong>Group</strong> 12<br />
-------------------------------------------------------------------------------<br />
INPUT GROUP: 12 -- Misc. Dispersion and Comput<strong>at</strong>ional Parameters<br />
---------------<br />
Horizontal size <strong>of</strong> puff (m) beyond which<br />
time-dependent dispersion equ<strong>at</strong>ions (Heffter)<br />
are used to determine sigma-y and<br />
sigma-z (SYTDEP) Default: 550. ! SYTDEP = 1.0E04 !<br />
Switch for using Heffter equ<strong>at</strong>ion for sigma z<br />
as above (0 = Not use Heffter; 1 = use Heffter<br />
(MHFTSZ) Default: 0 ! MHFTSZ = 1 !<br />
Stability class used to determine plume<br />
growth r<strong>at</strong>es for puffs above the boundary<br />
layer (JSUP) Default: 5 ! JSUP = 5 !<br />
Vertical dispersion constant for stable<br />
conditions (k1 in Eqn. 2.7-3) (CONK1) Default: 0.01 ! CONK1 = 0.01 !<br />
Vertical dispersion constant for neutral/<br />
unstable conditions (k2 in Eqn. 2.7-4)<br />
(CONK2) Default: 0.1 ! CONK2 = 0.1 !<br />
Factor for determining Transition-point from<br />
Schulman-Scire to Huber-Snyder Building Downwash<br />
scheme (SS used for Hs < Hb + TBD * HL)<br />
(TBD) Default: 0.5 ! TBD = 0.5 !<br />
TBD < 0 ==> always use Huber-Snyder<br />
TBD = 1.5 ==> always use Schulman-Scire<br />
TBD = 0.5 ==> ISC Transition-point<br />
Range <strong>of</strong> land use c<strong>at</strong>egories for which<br />
urban dispersion is assumed Default: 10 ! IURB1 = 10 !<br />
(IURB1, IURB2) 19 ! IURB2 = 19 !<br />
Site characteriz<strong>at</strong>ion parameters for single-point Met d<strong>at</strong>a files ---------<br />
(needed for METFM = 2,3,4)<br />
Land use c<strong>at</strong>egory for modeling domain<br />
(ILANDUIN) Default: 20 ! ILANDUIN = 20 !<br />
Roughness length (m) for modeling domain<br />
(Z0IN) Default: 0.25 ! Z0IN = 0.25 !<br />
Leaf area index for modeling domain<br />
9-30