Cap 15_Small_Lab_Equipment_OK2.indd - Euroclone

15. Small Lab Equipment
• Thermomixers
• Shaking Systems
• Benchtop Incubators
• Water Baths
• Centrifuges
• Photodocumentation
• UV Transilluminators
• Power Supplies
• Reader & Washer

15 Small Lab Equipment
Thermomixers
Dry Bath
EuroClone Dry Bath is a microprocessor-controlled product using
advanced thermoelectric technique. This technique allows more stable
and accurate temperature control both in the reaction block and in
the sample. Optional aluminium blocks are easily replaceable, to
hold different types of test tubes. Dry Bath allows to operate also in
programmable mode, linking a maximum of five different temperature
steps.
Features
User friendly LCD display.
Simultaneous display of set and real time and temperature.
Versatile and easy to use, meets all experimental requirements. Easy to clean and sanitise.
Customized blocks are available on request to suit specific demands.
Reliable design with internal extra temperature protection.
Temperature deflection adjusting meets all demands.
Microprocessor-controlled incubation time and temperature.
End of cycle beep-signal.
Technical Specifications
Temperature Range
- 10° C ~ 100° C
Timer
1 min ~ 99 h 59 min
Temperature Accuracy
< ± 0.3° C
Display Accuracy
0.1° C
Heating rate < 20 min (from 20° C to 100° C)
Cooling rate (*) < 30 min (from 20° C to - 10° C)
Heating and cooling elements Peltier modules
Dimensions (W x D x H)
300 x 220 x 170 mm
Weight (with block)
5 Kg
Power Supply
230 V 50 Hz
Available blocks
See “EC Block” table
(*) The instruments reach - 10° C if T ambient is < than 25° C
Cat. n°
EMK20
Description
EuroClone Dry Bath - Digital Dry Bath range T - 10 to 100° C - EC
block for tubes not included
T-Shaker Thermomixers
Designed for simultaneous heating and mixing of small samples,
T-Shakers are supplied with interchangeable platforms for microtubes.
Mixing and heating modes can be used both simultaneously and
independently, i.e. the device can work as a shaker and as a thermostat.
EMC100 Model controls temperature below ambient, reaching the
value of 0° C.EMC100 Model allows to operate also in programmable
mode, linking a maximum of five different temperature steps.
Features
LCD display. Easy to setup and use.
Accurately controls and displays time, temperature and speed.
Over heating protection device ensures safety & reliability.
Temperature can be calibrated to meet user needs.
Silent operation, even below 1.500 rpm.
Custom blocks are available to satisfy experimental requirements.
Gentle, reliable mixing with long-life direct current motor.
Cat. n°.
EMSC100
EMS100
Description
EuroClone T-Shaker Cool - Thermoshaker range T 0 - 100° C - EC
block for tubes not included
EuroClone T-Shaker Ambient - Thermoshaker range T RT + 5 - 100° C -
EC block for tubes not included
Technical Specifications
EMS100
EMSC100
Temperature Range Ambient + 5° C ~ 100° C 0° C ~ 100° C (*)
Timer 1 min ~ 99 h 59 min 1 min ~ 99 h 59 min
Temperature Accuracy < ± 0.5° C < ± 0.5° C
Display Accuracy 0.1° C 0.1° C
Mixing speed 200 - 1500 rpm 200 - 1500 rpm
Amplitude 2 mm 2 mm
Heating rate < 15min (from 20° C to 100° C) < 15min (from 20° C to 100° C)
Cooling rate (*) < 30 min from T amb. to (T amb. - 20° C)
Heating and cooling elements
Peltier modules
Dimensions (W x D x H) 300 x 220 x 170 mm 300 x 220 x 170 mm
Weight (with block) 7 Kg 8.5 Kg
Power Supply 230 V 50 Hz 230 V 50 Hz
Available blocks See “EC Block” table See “EC Block” table
(*) If T ambient is < 20° C; 4° C ~ 100° C if T ambient is < 25° C; 10° C ~ 100° C if T ambient is < 30° C
124

Small Lab Equipment 15
Benchtop not incubated shakers
Mini Shaker
EuroClone Mini Shaker guarantees the operator maximum reproducibility and
reliability, extremely silent magnetic traction, all in a small footprint.
When samples shaking is needed, Mini Shaker offers a gentle shaking
without noise or vibrations, even if fully loaded.
Features
Reliable brushless DC motor generates minimum noise and no vibration.
Artificial intelligence system which maintains precise speed and time control by
using MICOM.
LED indicates temperature, speed, time and power failure.
Operating speed up to 300 rpm even though stroke is 30 mm.
Suitable for operation in Cold Chambers and Incubators.
Easily changeable platform.
No belt and pulley drive system for shaking.
Technical Specifications
Speed
From 30 to 300 rpm
Accuracy ± 1%
Increments
1 rpm
Timer
1 min. to 48 hours or continuously
Increments
1 min
Accuracy ± 1%
Amplitude
25 mm
Platform dimensions
300 x 330 mm
Max. capacity
4 x 1000 ml
Dimensions (W x D x H)
300 x 330 x 70 mm
Power Supply
230 V 50 Hz
Weight
7 kg
Cat. n°
ENB101S
Description
Mini Shaker, Direct drive beltless - Speed 30 to 300 rmp
Platform 300 x 300 mm with rubber pad
Linear Digital Shaker
Shakerclone
Features
Compact, linear shaker with swivel motion, for a maximum shaking weight of 7.5 kg
LCD display for speed and timer adjustment. Speed, timer and operating mode can
be viewed simultaneously
Wide range of accessory platforms makes possible to use almost all shapes and
sizes of vessels
Wide speed range: 100-350 rpm/min
RS232 interface
Platform to be order separately
Technical Specifications
Voltage [VAC] 100-240
Frequency [Hz] 50/60
Power [W] 30
Shaking movement
Linear
Linear diameter [mm] 10
Max. shaking weight (with attachment) [kg] 7.5
Motor type
External rotor brushless motor
Max. power input of motor [W] 28
Max. power output of motor [W] 15
Speed range [rpm]
100-350 (Linear)
Speed display
LCD
Timer
Yes
Timer display
LCD
Time setting range [minutes] 1-1199
Run type
Timing/Continuous
Dimensions [W×H×D mm] 420×370×100
Weight [kg] 13.5
Maximum ambient temperature [°C] 5-40
Maximum relative humidity 80%
Protection class acc. DIN EN60529
IP21
Cat. n°
ESKL330PRO
Description
Linear Digital Shaker
125

15 Small Lab Equipment
Digital Magnetic Heated Stirrer
Stirrerclone
Technical Specifications
Voltage [VAC] 200-240
Frequency [Hz] 50/60
Power [W] 550
Stirring point position quantity 1
Max. stirring quantity (H 2
O) [liters] 20
Max. magnetic bar [mm] 80
Motor type
External rotor
brushless motor 10
Max. power input of motor [W] 18
Max. power output of motor [W] 10
Speed range [rpm] 100-1500
Speed display
LCD
Speed display accuracy [rpm] 1
Heating plate material
Stainless Steel
Diameter of the heating plate [mm] Ø135
Heating power [W] 500
Heating rate (1L H20) [K/min] 6
Temperature range [°C]
RT~340
Temperature display
LCD
Temperature display accuracy [°C] 0.1
Control accuracy of heating temperature [°C] 1
Temperature sensor in medium
PT1000
Control accuracy of heating temperature
with temperature sensor [°C]
0.2
Dimension [mm] 280×160×85
Weight [kg] 2.8
Maximum ambient temperature [°C]] 5-40
Maximum relative humidity 80%
Protection class acc. to DIN EN60529 IP42
RS232 interface
Built in accordance with the following safety
standards:
Built in accordance with the following
EMC standards:
Associated EU guidelines:
Instrument guidelines:
Yes
EN 61010-1
UL 3101-1
CAN/CSA C22.2(1010-1)
EN 61010-2-10
EN 61326-1
EMC-guidelines: 89/336/EWG
Instrument guidelines: 73/023/EWG
Features
Magnetic stirrer suitable for unsupervised operation, with optimized stirring technology
Easy-to-read backlit LCD display
Fuzzy logic control microprocessor technology guarantees maximum control accuracy
RS232 interface
High accuracy control of heating temperature and of safe working temperature
Stainless Steel Hotplate
Independent temperature sensor; safe working temperature can be set manually
Optional PT1000 temperature sensor
Warning display indicating presence of any residual heat when the unit is switched
off
DIN 12878 compliant socket for the use of contact thermometers
Cat n°.
EMSHPRO
Description
Digital Magnetic Heated Stirrer
Stirrerclone
Features
Magnetic stirrer suitable for unsupervised operation, with optimized stirring
technology
Easy-to-read backlit LCD display
Fuzzy logic control microprocessor technology guarantees maximum control
accuracy
RS232 interface
Technical Specifications
Voltage [VAC] 200-240
Frequency [Hz] 50/60
Power [W] 50
Stirring point position quantity 1
Max. stirring quantity H 2
O[liters] 20
Max. magnetic bar [mm] 80
Motor type
External rotor brushless motor
Max. power input of motor [W] 18
Max. power output of motor [W] 10
Speed range [rpm] 100-1500
Speed display
LCD
Speed display accuracy [rpm] 1
Heating plate material
Stainless Steel
Diameter of the heating plate [mm] Ø135
Dimensions [mm] 280×160×85
Weight [kg] 2.8
Maximum ambient temperature [°C] 5-40
Maximum relative humidity 80%
Protection class acc. to DIN EN60529 IP42
RS232 interface
Built in accordance with the following
safety standards:
Yes
EN 61010-1
UL 3101-1
CAN/CSA C22.2(1010-1)
EN 61010-2-10
Technical Specifications
Built in accordance with the following
EMC standards:
Associated EU guidelines:
Instrument guidelines:
Cat n°. Description
EMSPRO Digital Magnetic Stirrer
EN 61326-1
EMC-guidelines: 89/336/EWG
73/023/EWG
126

Small Lab Equipment 15
10-Channel Analog Heated
Magnetic Stirrer
Stirrerclone
Technical Specifications
Voltage [VAC] 200-240
Frequency [Hz] 50/60
Power [W] 490
Heating power [W] 470
Heating Temperature Range [°C]
RT-120
Stirring positions quantity 10
Max. stirring quantity of single stirring
position (H 2
O) [liters]
0.4
Stirring point position diameter [mm] 90
Single stirring position speed error [%] 5
Max. stirring quantity (H 2
O) [liters] 4
Max. magnetic bar [mm] 40
Motor type
External rotor brushless motor
Max. power input of motor [W] 12
Max. power output of motor [W] 4
Speed range [rpm] 0-1100
Speed display
Scale
Heating plate material
Silicone coated Stainless Steel
Dimensions of Plate [mm] 180×450
Overall Dimensions [mm] 182×552×65
Weight [kg] 3.2
Maximum ambient temperature [°C] 5-40
Maximum relative humidity 80%
Protection class acc. to DIN EN60529 IP42
Features
High-performance multi-position magnetic stirrer with 10 stirring positions
Step less speed regulation. Wide speed range: 0-1000rpm
Electronic speed control motor provides constant speed during changes in load
Inner set temperature control panel, uniform temperature distribution
Stainless steel plate, silicone coated, anti-slip and anti-corrosion
Cat n°.
EMSHS10
Description
10-Channel Analog Heated Magnetic Stirrer
Adjustable Speed Vortex Mixer
VORTEXCLONE
Features
Vortex mixer suitable for touch or continuous operation
Universal adapter included for test tubes and small vessels up to Ø30 mm
Wide speed range: 0-2500 rpm/min
Can be used for various shaking application with optional adapters for PCR tubes etc
Adapters securely clicked onto appliance in any position
Sturdy single mould casing
Specially designed silicone feet and steel base for excellent vibration damping
Technical Specifications
Voltage [VAC] 220-240
Frequency [Hz] 50/60
Power [W] 60
Shaking movement
Orbital
Orbital diameter [mm] 4
Max. power input of motor [W] 58
Max. power output of motor [W] 10
Speed range [rpm] 0-2500
Speed display
Analog Scale
Run type operation
Continuous / touch
Dimensions [W×H×D mm] 127×130×160
Weight [kg] 2.5
Maximum ambient temperature [°C] 5-40
Maximum relative humidity 80%
Protection class acc. to DIN EN60529 IP21
Cat. n°.
EMXS
Description
Adjustable speed Vortex Mixer with universal adapter for test
tubes and small vessels upto Ø30 mm
127

15 Small Lab Equipment
Fixed speed Vortex Mixer
VORTEXCLONE
Features
Vortex mixer suitable for touch or continuous operation
Universal adapter Included for test tubes and small vessels up to Ø30 mm
Fixed speed range 2500 rpm/min
Sturdy single mould casing
Specially designed silicone feet and steel base for excellent vibration damping
Technical Specifications
Voltage [VAC] 220-240
Frequency [Hz] 50/60
Power [W] 60
Shaking movement
Orbital
Orbital diameter [mm] 4
Max. power input of motor [W] 58
Max. power output of motor [W] 10
Speed range [rpm] 2500
Run type operation
Continuous / touch
Dimensions [W×H×D mm] 127×130×160
Weight [kg] 2.5
Maximum ambient temperature [°C] 5-40
Maximum relative humidity 80%
Protection class acc. to DIN EN60529 IP21
Cat. n°.
EMXF
Description
Fixed speed Vortex Mixer with universal adapter for test tubes and
small vessels up to Ø30 mm
Benchtop Incubators
Benchtop Incubated Shaker
Shake’n Bator
EuroClone Shake’n Bator guarantees the operator maximum
reproducibility and reliability, extremely silent magnetic traction, all
in a small footprint. When samples shaking and temperature control
is needed, Shake’n Bator offers a gentle shaking without noise or
vibrations, even if fully loaded and an accurate temperature control.
Thanks to the isolation of the shaking mechanism, it is possible
to grow cultures and maintain samples at controlled temperature
simultaneously.
Features
Provides 2 functions (shaking culture and general culture) at the same time.
Shaking culture without shelves vibration.
Artificial intelligence system which maintains precise temperature by using MICOM.
Benchtop model.
Control device (TAC system) makes uniform heating for natural convection.
Brushless DC motor provides low noise and no vibration.
LED indicates temperature, speed, time and power failure.
Internal glass window to check samples status without disturbing the growth
environment.
Inner chamber made with AISI 304 Stainless Steel.
Shaking platform features a simple and easy to use fixing mechanism.
Technical Specifications
Temperature Range
Ambient + 5° C to 60° C
Increments
0.1° C
Speed
From 30 to 300 rpm
Accuracy ± 0.1 %
Increments
1 rpm
Timer
1 min to 48 hours or continuously
Accuracy ± 0.1 %
Increments
1 min
Amplitude
22 mm
Internal volume
142 lt
N° of shelves 2 + 1 platform
Platform dimensions
400 x 400mm
Max. Capacity
4 x 1000 ml
Internal Dimensions (W x D x H) 480 x 430 x 690 mm
Overall Dimensions (W x D x H) 545 x 530 x 865 mm
Power Supply
230 V 50 Hz
Weight
82 kg
Cat. n°
ENB205QUP
Description
Shaker & Incubator - Temp. Range: Ambient + 5° C to 60° C -
Speed Range: 25 rpm to 300 rpm Capacity / Shelves: 142 liter / 1
platform 450 x 400 mm + 2 shelves
128

Small Lab Equipment 15
Dry Wall Incubators
Blue Bator
EuroClone Blue Bator dry wall incubators are developed and manufactured
to offer the right answer when a precise temperature control is needed over
all the working range, particularly in microorganism culture, growth tests,
flocculation tests and many others. Built in as a standard, Microprocessor
high precision control, allows to heat the inner chamber at a range between
+ 5° C on ambient to 65° C, with an accuracy of ± 0.1° C. Acoustic and
visual alarms for overtemperature are incorporated.
The sealed control panel offers a simple programming of the parameters
and a quick readout. The non volatile memory keeps the set values during
potential black outs, allowing the automatic restart of the unit.
The inner chamber mirror finish stainless steel is easy to clean and long
lasting.
Features
Built-in microprocessor accurately controls the heating temperature.
The heating element is protected by a diffusion screen that simplify the air
circulation.
The internal fan is located on the upper part of the working chamber and is
protected by a stainless grill.
The soft touch membrane control panel dispIays temperature and time on LED digits.
All the parameters are independently set and controlled.
Adjustable shelves as standard.
Internal glass door allows the samples visual control without disturbing the
working conditions.
Technical specifications
Cat. n°
EDHP9052
EDHP9082
EDHP9162
EDHP9272
Description
Blue Bator Digital Incubator, T Range from Amb. T to 65°
C, Internal volume 50 lt
Blue Bator Digital Incubator, T Range from Amb. T to 65°
C, Internal volume 80 lt
Blue Bator Digital Incubator, T Range from Amb. T to 65°
C, Internal volume 160 lt
Blue Bator Digital Incubator, T Range from Amb. T to 65°
C, Internal volume 270 lt
EDHP9052 EDHP9082 EDHP9162 EDHP9272
Temperature Range Ambient + 5 °C - 65° C Ambient + 5 °C - 65° C Ambient + 5 °C - 65° C Ambient + 5 °C - 65° C
Display resolution 0.1° C 0.1° C 0.1° C 0.1° C
Timer 1 - 9999 min 1 - 9999 min 1 - 9999 min 1 - 9999 min
Shelves 2 2 3 3
Chamber Volume 50 lt 80 lt 160 lt 270 lt
Inner Dimensions
(W x D x H)
415 x 360 x 355 mm 500 x 400 x 400 mm 500 x 500 x 650 mm 600 x 600 x 750 mm
Outer Dimensions
(W x D x H)
690 x 500 x 500 mm 780 x 530 x 560 mm 790 x 630 x 810 mm 890 x 740 x 910 mm
Supply 230 V 50 Hz 230 V 50 Hz 230 V 50 Hz 230 V 50 Hz
Power 250 W 350 W 550 W 700 W
Weight 30 kg 50 Kg 70 Kg 85 Kg
129

15 Small Lab Equipment
Water baths
12 liters orbital or reciprocal shaking
water bath
The EuroClone water baths SHWB and SRWB combine water thermal
uniformity with magnetic shaking to offer quiet, vibration free, stable
and precise performances.
Features
Artificial intelligence system (TAC System) which maintains precise thermostatic
control by using MICOM.
The heating element is located under the bath, not inside the chamber.
Brushless DC motor provides low noise and no vibration.
LED indicates temperature, speed, time and state of power failure.
The instruments are equipped as standard, with a sprig rack for a wide
range of tubes, flasks, etc.
Deep drawn stainless steel bath. Gable cover as an option.
Technical specifications
ENB303
ENB304
Movement Orbital Reciprocal
Temperature Range Ambient + 5° C to 80° C Ambient + 5° C to 80° C
Accuracy ± 0.1° C to 37° C ± 0.1° C to 37° C
Speed 30 to 200 rpm 30 to 200 rpm
Accuracy ± 1 % ± 1 %
Amplitude 30 mm 30 mm
Timer 1 min. to 48 hours or continuously 1 min. to 48 hours or continuously
Capacity 12 lt 12 lt
Internal dimensions (W x D x H) 240 x 300 x 150 mm 240 x 300 x 150 mm
Overall dimensions (W x D x H) 270 x 350 x 210 mm 270 x 350 x 210 mm
Power Supply 230 V 50 Hz 230 V 50 Hz
Weight 20 kg 20 kg
Cat. n° Description
Shaking Water Bath, Orbital motion - 12 lt capacity
Temp. Range: Ambient + 5° C to 100° C
ENB303 Speed range 30 to 200 rpm
Stroke 30 mm
Spring rack as standard
Shaking Water Bath, Reciprocal motion - 12 lt capacity
Temp. range ambient + 5° C to 100° C
ENB304 Speed range 30 to 200 rpm
Stroke 30 mm
Spring rack as standard
12 liters water baths with static
or stirring functions
The EuroClone SWB and WB water baths offer compact design,
robust construction, accurate and stable temperature control. A smart
magnetic stirrer is incorporated in the SWB model, allowing the liquid
in the bath or even in a flask to be mixed when needed.
Features
Artificial intelligence system (TAC System) which maintains precise thermostatic
control by using MICOM.
Built-in Magnetic Stirrer in the bottom of the bath which stirs water in the
bath and liquid in the flask simultaneously. (ENB302)
Sample in the flask is stirred while water is circulated allowing a precise
Cat. n° Description
experiment. (ENB302)
ENB301 Water Bath, 12 lt capacity, Temp. range ambient + 5° C to 100° C
The heating element is located under the bath, not inside the chamber.
Stirring Water Bath, 12 lt capacity, Temp. range ambient + 5° C to 100°
ENB302
LED indicates temperature, speed (ENB302), time and state of power failure.
C - Speed range 60 to 1000 rpm
Technical specifications
ENB301
ENB302
Temperature Range Ambient + 5° C to 100° C Ambient + 5° C to 100° C
Accuracy ± 0.1° C to 37° C ± 0.1 °C to 37° C
Speed 60 to 1000 rpm
Accuracy ± 1%
Capacity 12 lt 12 lt
Internal dimensions (W x D x H) 240 x 300 x 150 mm 240 x 300 x 150 mm
Overall dimensions (W x D x H) 270 x 350 x 210 mm 270 x 350 x 210 mm
Power Supply 230 V 50 Hz 230 V 50 Hz
Weight 15 kg 15 kg
130

Small Lab Equipment 15
Centrifuges
Bench top centrifuge
Speed Master 14
The Speed Master 14 combines compact size with high speed. The clever
design results in a compact footprint with generous capacity which not only
save precious bench space but also provides the flexibility to alternate from
microvolume centrifugation to medium-volume centrifugation for up to 300
ml (6 x 50 ml tubes) of sample.
Technical specifications
Maximum speed
14,000 rpm (EFA15C rotor)
Maximum RCF
20,280 x g (EFA15C rotor)
Maximum capacity
300 ml (6 x 50 ml)
Drive Mechanism
Brushless induction
Control
Microprocessor based
Speed Range
300 - 14,000 rpm (100 rpm increments)
Speed Accuracy
± 20 rpm
Speed / RCF conversion yes
Timer
1 min - 99 hrs 59 mins plus hold function
Display
Backlight LCD
Operating noise
< 53 dB (A)
Acceleration / Deceleration 9 stages / 9 stages
Automatic Rotor identification yes
Imbalance Detection
yes
Dimensions (W x D x H) 340 x 490 x 380 mm
Weight (no rotor)
40 Kg
Power supply
230 V 50 Hz 8 A
Cat. n° Description
EV142
Speed Master 14 - Benchtop centrifuge. Max Speed 14000 rpm - Max
Capacity 6 x 50 ml
Features
Smart, Compact, 2 - in - 1 Design
Quick Set and forget Rotor System
Auto rotor recognition
Fast Acceleration and Deceleration
High imbalance tolerances
User friendly operation and information rich display
Quiet Operation
Liquid Seeping Prevention
Bench top refrigerated centrifuge
Speed Master 14R
The Speed Master 14R combines powerful and efficient refrigeration with
high speed centrifugation (maximum speed of 14,000 rpm / 20,290 xg with
the FA15C rotor). The clever design results in a compact footprint with generous
capacity which not only save precious bench space but also provides the
flexibility to alternate from microvolume centrifugation to medium-volume
centrifugation for up to 300 ml (6 x 50 ml tubes) of sample.
Technical Specifications
Maximum speed
14,000 rpm (EFA15C rotor)
Maximum RCF
20,290 x g (FEA15C rotor)
Maximum capacity
300 ml (6 x 50 ml)
Drive Mechanism
Brushless induction
Control
Microprocessor based
Speed Range
300 - 14,000 rpm (100 rpm increments)
Speed Accuracy
± 20 rpm
Speed / RCF conversion yes
Timer
1 min - 99 hrs 59 mins plus hold function
Display
Backlight LCD
Operating noise
< 58 dB (A)
Temperature Range
- 20° C to + 40° C
Temperature Accuracy ± 2° C
Acceleration/Deceleration 9 stages / 9 stages
Automatic Rotor identification yes
Imbalance Detection
yes
Dimensions (W x D x H) 560 x 500 x 380 mm
Weight (no rotor)
60 Kg
Power supply
230 V 50 Hz 10 A
Cat. n° Description
EV142R
Speed Master 14R - Refrigerated Benchtop centrifuge.
Max Speed 14000 rpm - Max Capacity 6 x 50 ml
Features
Quick “Set and Forget” Rotor System
Auto rotor recognition
Fast Acceleration and Deceleration
High imbalance tolerances
Powerful Refrigeration
Actual sample (rotor) temperature Measurement and Display
Safety is Paramount
User friendly operation and information rich display
Quiet Operation
Liquid Seeping Prevention
131

15 Small Lab Equipment
Speed Master 18R
The Speed Master 18R delivers high capacity, refrigerated centrifugation
with an impressive maximum speed of 18,000 rpm (27,070 x g) (with
the fixed angle A18 rotor) and all from the convenience of a benchtop
instrument.
Technical Specifications
Maximum speed
Maximum
Maximum capacity
Drive Mechanism
Control
Speed Range
Speed Accuracy
Speed / RCF conversion
Timer
Display
Operating noise
Temperature Range
Temperature Accuracy
Memory
Acceleration / Deceleration
Automatic Rotor identification
Imbalance Detection
Dimensions (W x D x H)
Weight (no rotor)
Power supply
18,000 rpm (EFA18A rotor)
27,070 x g (EFA18A rotor)
1,000 ml (4 x 250 ml)
Brushless induction
Microprocessor based
300 - 18,000 rpm (100 rpm increments)
± 20 rpm
yes
1 min - 99 hrs 59 mins plus hold
function
Backlight LCD
< 58 dB (A)
- 20° C to + 40° C
± 2° C
9 programs
9 stages / 9 stages
yes
yes
730 x 610 x 380 mm
100 Kg
230 V 50 Hz 10 A
Features
Quick “Set and Forget” Rotor System
Auto rotor recognition
Fast Acceleration and Deceleration
High imbalance tolerances
Powerful Refrigeration
Actual sample (rotor) temperature Measurement and Display
Safety is Paramount
Quiet Operation
Liquid Seeping Prevention
Cat. n°
EV18R2
Description
Speed Master 18R - Refrigerated Benchtop centrifuge.
Max Speed 18000 rpm - Max Capacity 4 x 250 ml
Photodocumentation
GellyDoc Imaging Systems
GellyDoc is a compact and economic system for basic gel documentation.
Images of the gel can be seen through the color LCD screen, pictures
are captured with the high resolution digital camera and saved into
the memory card or instantly printed on the laboratory quality photo
printer included with the system. The camera can be connected to a PC
with a USB cable (not included) for transferring images.
Technical Data
DigiCam 60
LCD Screen:
Darkroom
Emission Filters
Transilluminator
Color Printer
Combination Lock
Dimensions
Color digital camera 10.0 megapixel
SD memory card (16 MB minimum)
Power cord included (batteries not required)
5.6” TFT LCD Monitor with video color
High resolution screen
Mounted on the GellyDoc hood
Connected to the camera for preview of images
UV blocking viewer window
Lightweight and compact
Handles for easy transport of the hood
Fits on top of the transilluminator
EtBr Red 570-640nm
The system is designed for use UV Transilluminators with
filter sizes not bigger than 21 x 26 cm
M-20V and M-26V feature variable intensity settings
300 x 300 resolution
4x6 in. prints
USB connectivity
108 prints included
Dimensions 7 x 5 x 2.5 in. (178 x 127 x 64 mm)
3 digit resettable combination
2 ft. cable
17H x 13.25W x 9.5D in. (432 x 337 x 241mm)
Features
DigiCam 60 color camera with 10.0 megapixel resolution
Lightweight, compact hood provides a compact darkroom environment, hood
now includes a new UV blocking viewer window that allows the visualization of
the gel
LCD screen included
Benchtop UV Transilluminator delivers back-lit UV; select from several benchtop
models (dimension equal or lager than 34 x 24 cm)
Color printer generates instant 4" x 6" low cost, laboratory quality color prints
Ethidium bromide filter for fluorescent stained gels included
Combination lock secures the camera to the darkroom
Cat.
EMF010001
EMF010005
Description
GellyDoc
GellyDoc + UV Transilluminator (Cod EM-TCX-26M)
132

Small Lab Equipment 15
UV Transilluminators
EuroClone has a wide range of UV trasilluminators available either with 8
or 15 Watt lamps with different dimensions even with double wave lenght.
Features
• Long life UV filters: the filters are design to transmit specific ultraviolet
rays and to absorb most of the visible light produced by the UV tubes. They
provide the maximum UV transmission over their surface. They have an
unlimited life expectancy
• Ondulex ® high efficiency reflector. Ondulex ® is a special polished
reflector which provides supreme UV output.
The reflector is located behind the UV tubes to reflect the maximum
of the light to the outside. The UV intensity of the whole instrument is
dramatically increased, as well as its performance
• Protection Transparent Screen
Compact Transilluminators
These transilluminators combine compact footprint and economy for
laboratories with budget in mind.
The fully adjustable UV safety screen can be positioned to suit the operator’s
viewing angle against exposure to harmful UV rays.
The transilluminators are electronically controlled. This reduces the heat and
eliminates the flickering effect for gel-documentation.
Features
Electronic ballast / Microprocessor controlled
No flickering effect thanks to its 25 KHz high frequency
The same model can be used from 100 to 240 Volt and from 50 to 60 Hz without
any intervention
Reduced electrical consumption
Unlimited filter life expectancy for 312 and 365 nm
Dual intensity selector (100%-70%)
Ondulex ® reflector
High UV output
Adjustable UV safety screen
Stainless steel frame
Cat. Description Dimensions Tubes
EM-TCX-15M Compact 15 ,312 15 x 15 cm 6 x 8 Watt
EM-TCX-20M Compact 20, 312 20 x 20 cm 6 x 8 Watt
EM-TCX-26M Compact 26, 312 21 x 26 cm 6 x 8 Watt
Photo UV Transilluminators
Photo UV are 15 Watt transilluminators characterized by supreme light
stability. With these transilluminators gel visualization and gel documentation
is strongly improved.
The transilluminator heat is considerably reduced, avoiding the use of extra
cooling fan and thus reducing the noise.
Thanks to its very high UV output, the transilluminator provides more signal
compared to a standard 8-watt transilluminator.
Features
High UV output
Electronic ballast / Microprocessor controlled
No flickering effect thanks to its 25 KHz high frequency
Unnecessary cooling due to the electronic control
Weight reduction
The same model can be used from 100 to 240 Volt and from 50 to 60 Hz without
any intervention
Reduced electrical consumption
Unlimited filter life expectancy for 312 and 365 nm
Ondulex ® reflector
Adjustable UV safety screen
Stainless steel frame
Cat. Description Dimensions Tubes
EM-TFX20M Photo UV 20, 312 20 x 20 cm 6 x 15 Watt
EM-TFX35M Photo UV 35, 312 20 x 35 cm 6 x 15 Watt
If you need a particular model, variable wave lenght, particular dimension, 254 or 365 nm filters or more details please contact our Customer Support (TSA) e-mail: tsa@euroclone.it
133

15 Small Lab Equipment
Power Supplies
Mini Pro 300V Power Supply
Combining small size and versatility, the newly redesigned Mini Pro
300V power supply is an ideai choice for any researcher. Capable of
providing constant voltage or constant current in 1V or 1 mA steps,
the unit is perfectly suited to run both vertical polyacrylamide or
horizontal agarose gel electrophoresis experiments. Continuous or
timed operation are easily performed using the simple and user-friendly
interface. The Mini Pro 300V features 2 electrode pairs, allowing
for 2 gels to be run simultaneously, saving both time and valuable
bench space. With a universal voltage rating, the Mini Pro 300V is
also designed and constructed to the most rigorous safety standards.
Packages including single or dual horizontal electrophoresis systems
and mini vertical electrophoresis systems are excellent choices for
educational or personal use.
Features
New housing and exterior design
Constant voltage or constant current operation
1V step voltage selection; lmA step current selection
400mA maximum current
60W maximum power
Two pairs of outlet terminals
Timer with alarm function
Safety device
Compact size and lightweight
Competitive pricing choice
Packages with midi sized horizontal electrophoresis systems and vertical
electrophoresis systems
Cat.
EMMINI300
Description
Mini Pro 300V Power Supply
MP 300V Power Supply
MP 300V Power Supply is a microprocessor-controlled Power Supply
with full control range of designated current and/or voltage. Its
maximum voltage output is up to 300 V and is designed to meet
most electrophoresis needs in a personal, single, easy to use unit.
MP 300V Power Supply is capable of running horizontal and vertical
electrophoresis, and two-dimensional electrophoresis, SDS-PAGE
applications. In addition, a timer with alarm function is also equipped
in the unit, and so it is pause function.
Furthermore, the powerful specifications plus four pairs of terminators
could be used for multi electrophoresis units simultaneously. The design
of stackability is another feature to save bench top space.
MP300V Power Supply also provides Constant Voltage or Constant
Current to instruments used in electrophoresis.
Four (4) pairs of terminators and the much powerful specification
equipped enable the maximum capability of MP 300V Power Supply
series compared to other existing similar products on the market.
Features
Output Voltage/Inc 2-300 V/1 V
Output Current/Inc 1-700 mA/1 mA
Max. Watt
150 W
Operating Constants Voltage or Current
Control
Microprocessor Controller
Terminator Pairs 4 pairs
Timer
1-999 mins with alarm, continuous
No load detect, leakage detect, overload
Safety Device
detect, load change dectect, over temperature
protection, shrouded plugs and sockets
Crossover
Yes
Operating Temperature Ambient to 40 °C
Unit Dimension
W 190 x L 275 x H 95 mm
Construction
ABS faceplate and aluminum
Weight
2.5 kg
Rated Voltages
100-240 V
Cat.
EMMP300V
Description
MP 300V Power Supply
134

Small Lab Equipment 15
MP 500V Power Supply
MP 500V Power Supply is a microprocessor-controlled Power Supply for
most electrophoresis needs. MP 500V is a programmable mode, and it is
capable of running horizontal and vertical electrophoresis, SDS-PAGE, native
PAGE applications, two-dimensional electrophoresis, and electro-blotting.
Furthermore, the powerful specifications plus four pairs of terminators
can be used for multi electrophoresis units simultaneously. In addition, a
timer with alarm function is equipped in the unit, and so is pause function.
MP 500V Power Supply provides Constant Voltage or Constant Current
or Constant Power used in electrophoresis. 2.6” LCD shows the running/
setting condition and also provides a user friendly interface and convenience
to the user. Advanced safety design concerns are outstanding features of MP
500V Power Supply.
Features
Output Voltage/Inc 5-500 V/1 V
Output Current/Inc 600 mA /1 mA
Output Watt/Inc
300 W/1 W
Operating Constants Voltage or Current or Power
Control Microprocessor Controller
Program Storage 30 programmed files
Program Multi-Step Up to 6 steps
Terminator Pairs
4 pairs
LCD Display 2.6’’
Timer
1-999 mins with alarm, continuous
No load detect, leakage detect, overload detect, load
Safety Device
change detect, over voltage detect, over temperature
protection, shrouded plugs and sockets
Crossover
Yes
Operating Temperature Ambient to 40 °C
Unit Dimension
W 190 x L 275 x H 95 mm
Construction
ABS faceplate and aluminum
Weight
2.5 kg
Rate Voltages
100-240 V
Cat.
EMMP500V
Description
MP 500V Power Supply
MP 3AP Power Supply
MP 3AP Power Supply is considered as one of the most powerful Power
Suppy on the market. It is a microprocessor- controlled Power Supply that
can be used for most electrophoresis needs. MP 3AP is also a programmable
mode, and it is capable of running horizontal and vertical electrophoresis,
SDS-PAGE, native PAGE applications, two-dimensional electrophoresis, and
electro-blotting. Furthermore, the powerful specifications plus four pairs of
terminator can be used for multi electrophoresis units simultaneously. In
addition, a timer with alarm function is equipped in the unit, and so is pause
function. MP 3AP Power Supply provides Constant Voltage or Constant
Current or Constant Power used in electrophoresis. 2.6” LCD shows the
running/setting condition and also provides a user friendly interface and
convenience to the user. Advanced safety design concerns are outstanding
features of MP 3AP.
Features
Output Voltage/Inc 5-300 V/1 V
Output Current/Inc 10-3000 mA/1 mA
Output Watt/Inc 300 W/ 1W
Operating Constants Voltage/current/power
Control
Microprocessor Controller
Program Storage 30 programmed files
Program Multi-Step Up to 6 steps
Terminator Pairs
4 pairs
LCD Display 2.6’’
Timer
1-999 mins with alarm, continuous
No load detect, leakage detect, overload detect, load
Safety Device
change detect, over voltage detect, over temperature
protection, shrouded plugs and sockets
Crossover
Yes
Operating Temperature Ambient to 40 °C
Unit Dimension
W 190 x L 275 x H 95 mm
Construction
ABS faceplate and aluminum
Weight
2.5 kg
Rate Voltages
100-240 V
Cat.
EMMP3AP
Description
MP 3AP Power Supply
135

15 Small Lab Equipment
Reader & Washer
LT-4000 Visible
LT-4000 is an absorbance reader suitable for ELISA and the most
common colorimetric assays in visible range. The system can either
be controlled thorugh the touch screen or by a PC using the Manta
Software (supplied with the reader).
Features
Multi beam detector
Allows a 96 well palte to be read in as little as 5 seconds
Touchscreen interface
Large clear screen with touchscreen interface allows easy control of instrument and visualization of data
Shake mode
Allows brief mixing of plate before read to ensure consistent results
Large built in memory
Allows on board storage of 100 programs and up to 10,000 results
Lamp energy saving mode
Gratly increases lifespan of the lamp and reduces user maintenance
Direct print facility
Capable of interfacing with PCL laser printers via USB
Short warm up time
Instrument is ready to read plates after only 90 second warm up
LT-4000 is supplied with 405, 450, 492 and 630 nm filters as standard. A wide range of filters between 400 and 700
Wide range of filters available
nm filters are available at low cost for the instrument
Wide range of on board data processing available:
1. Absorbance model
2. Cut off mode
3. Single standard mode
4. Point to point mode
9 different calculation modes available
5. % absorbance mode
6. Linear regression mode
7. Index regression mode
8. Logarithm regression mode
9. Exponent regression mode
Easy plate layout setup
Large touchscreen interface makes it easy to set out plate
Integrated dust cover
Built in dust cover for plate carrier, keeps detectors free from dust
Manta Sofware: Fully featured reader control and data analysis software included
Features
Quick start wizard
Kinetic reads
Custom microplate layouts
GLP features
Automated data analysis wizard
Multiple data views
Choice of data export options
Technical data
Wavelength range: 400 – 750nm.
Photometric Range: 0.000 - 4.000 Abs
Resolution: 0.001 Abs (displayed) 0.0001 Abs (calculated)
Light Source Halogen lamp, 8V/50W
Wavelengths 405, 450, 492, 630 nm (4 additional filters optional)
Wavelength Accuracy: ±1 nm
Bandwidth: 8 nm
Calculation Method (on-board): Abs, %Abs, cut-off, linear, point to point,
log, exponential, power regression
Accuracy: ±1% or ±0.005A
Reading Speed: 5 seconds for 96-well plate (single wavelength)
Shaking Adjustable speed and time
Memory 100 tests, up to 10,000 test results
Interface: RS-232, PSTN (optional)
Display: 6” LCD
Input: Touch panel or mouse
Output: External printer or software (optional)
Net Weight: 8kg.
Dimensions: (L x W x H) 460 x 330 x 300 (mm)
Power Supply: AC 110V-220V ±10%, 50-60Hz
Step by step design of protocols using Manta software. Allows you to select read type, wavelenth, shake speed/
duration, microplate layout, data export options
Manta software allows you carry out single or dual wavelenth kinetic reads using the LT-4000. As a stand-alone
instrument the LT-4000 is only able to carry out endpoint (single measurement) reads. Kinetic reads allow you to take
multiple readings over a time course
Manta has a wide range of preset microplate layotus already setup. You can also setup layouts yourself and label wells
with their contents (e.g. blank, standard, control or sample)
Allows you to enter user names and further info for each plate
Can be setup either before or after reading the plate. If setup after then it will study the assay you have run and
suggest the most appropriate data analysis. There is a wealth of qualitative and quantitative data analysis options to
choose from. This is a lot more user friendly than rival software programs
Choose how you wish to view your data (matrix, table or bar chart) Bar charts can be rotated. Individual graphs can
be shown for each well of kinetic data
Data and reports can be exported to excel, word or html
Cat.
EMLT4000MS
Description
EuroClone LT-4000 Visible ABS Reader
136

Small Lab Equipment 15
Washer LT-3000
LT-3000 is a simple and robust washer suitable for any basic application
requiring accurate washing of microplates.
Features
Comes with both (8 and 12 way) Interchangeable manifolds
Automated monitoring of vacuum and pressare
Automatic monitoring of liquid level in waste bottle
Automatic monitoring of strip / plate presence
Fully automated washing
Allows up to 12 wash cycles
Wash number (0-12) and volume (50-2000 microliter) adjustable
Double aspiration
Washes 48/96 well flat, round or v bottom plates (or strips)
Allows storage of up to 50 programmes
Separate aspirate and dispense nozzles
Easy maintenance:
✓ Dedicated rinse cycle
✓ Nozzle cleaning needles provided
✓ User replaceable manifold
Cat.
EMLT3000MS
Description
EuroClone LT-3000 Washer
Easily swapped by user needing no tools. Enables optimal washing of strips / 48 well plates (8
way manifold) or 96 well plates (12 way manifold)
Eliminates potential overflowing of wells if vacuum connections not tightened correctly
Float sensor to prevent overflowing of waste bottle and spillage of potentially contaminated
liquid
Prevents machine starting if plate / strip not present and consequent risk of flooding
No user involvement required. Place plate / strip on machine and come back once done. Also
gives more thorough washing, far better consistency and lower residual volume than manual
plate washing
Suitable for even the most demanding wash protocols
Allows easy optimization of wash protocol
Aspirates each well twice in middle then at edge of well to minimize residual volume (can be
as little as 1 microlitre with v bottom wells)
Optimised wash settings for all commonly used plate types to ensure minimal sample
disturbance and residual volume
Ideal for multi user environments. Programmes easily accessed via menu system
Minimises the risk of blockage common with concentric nozzles. Well separated paths for
clean and dirty buffer
Simply transfer pump into a beaker of distilled water after final use of the day and press rinse
button. The machine automatically flushes through all tubing and manifold. This prevents
blockage due to buffer crystallization
If machine is left for a long period without having been rinsed then the manifold can be
easily lifted off and blockage cleared using provided needles
Manifold is connected to the machine by 2 screw connected tubes and simply sits on arm.
This allows easy changing of the manifold between 8 and 12 way (or replacement if ever
required)
137