zirkon 10 GB - Euro Globtrade

Power harrow
Zirkon 10

LEMKEN Zirkon 10
The concept
Changing the rotation
The Zirkon 10 is suitable for highest long-term operational
demands both in conventional or minimum cultivation
systems. The heavy gauge underside of the trough and
the bearing spaces between rotors create outstanding
strength. LEMKEN offers this new power harrow in working
widths from three to six metres. For preparing ground
for a mulch system or working in especially hard
ground conditions the Zirkon 10 is operated with forward-sloping,
grade set tines. Following the plough or on
stony areas it is advantageous to use the tines in a drag
setting.
With the new Dual-Shift concept from LEMKEN the driving
gear can be simply moved 20 mm between two
stops after the loosening with a spindle of three bolts.
This reverses the direction of travel of the tines.
Additionally, the new Dual-Shift gear allows rapid and
simple alteration of tine rpm via a lever at the gear box.
Depending on lever position, 330 or 440 rpm can be
selected with tractor pto at 1000 rpm.

The new generation
The Dual-Shift gear
The quick-change system
The change of the rotation is achieved through the primary
drive of the Zirkon 10 no longer directly driving
rotor shafts but instead driving a cog wheel between two
rotor shafts. Through the sliding of this cog into a certain
position, either the right hand or the left hand rotor is
driven by the cog and therefore the desired direction of
travel activated.
Zirkon 10 includes new quick-change Allround knife tines
as standard. Each pair of tines is attached by a single
security pin. Changing tines requires no tools and is therefore
rapidly carried out. The attachment parts are
situated underneath the tine carrier so that the resultant
greater amount of free space between the tines together
with the smooth underside of the trough play a large role
in avoiding jamming of stones, among other things. The
new quick-change tines are 340 mm in length and 20
mm thick allowing ample wear material for long working
life without down time. The tines are also available in
hard faced versions.

The Allround knife tines
The Allround knife tines differ from the power harrow tines up until now
through edges that are sharpened on both sides. Thus, depending on the
working conditions, they can be mounted in the drag or the grad position.
The tine form, which is lightly inward curving, avoids soil smearing in the
drag position. Power harrow tines mounted in this position have a better
surface levelling effect in both seedbed preparation after the plough as well
as in conservation cultivations. Stones can be driven over without problems
and stay in the ground. In the grade position, the Allround tines demonstrate
their strengths in mulch seeding preparation with intensive mixing of soil
and vegetation. Where seedbeds are being prepared on the plough furrow,
this tine position pushes the finer soil particles into the seed horizon depth.
Rougher crumbs remain on the soil surface and so reduce the danger of
capping and loss of soil through water or wind erosion.
Technical data
Working Weight Transport PTO Rotor Number of
Up to Description width without roller width rpm rpm rotors
kW (PS) (approx. cm) (approx. cm) (approx. m) (min-1) (min-1)
- rigid -
147 (200) Zirkon 10 / 300 300 922 3.0 1,000 330 / 440 12
162 (220) Zirkon 10 / 400 400 1,149 4.0 * 1,000 330 / 440 16
170 (230) Zirkon 10 / 450 450 1,263 4.5 * 1,000 330 / 440 18
- hydraulically foldable -
184 (250) Zirkon 10 / 400 K 400 1,774 3.0 1,000 330 / 440 16
199 (270) Zirkon 10 / 450 K 450 1,908 3.0 1,000 330 / 440 18
213 (290) Zirkon 10 / 500 K 500 2,078 3.0 1,000 330 / 440 20
235 (320) Zirkon 10 / 600 K 600 2,464 3.0 1,000 330 / 440 24
- hydraulically folded, combination -
184 (250) Zirkon 10 / 400 KA 400 3,543 3.0 1,000 330 / 440 16
199 (270) Zirkon 10 / 450 KA 450 3,746 3.0 1,000 330 / 440 18
213 (290) Zirkon 10 / 500 KA 500 3,935 3.0 1,000 330 / 440 20
235 (320) Zirkon 10 / 600 KA 600 4,459 3.0 1,000 330 / 440 24
* Exceeds the permitted transport width in some countries
Zirkon 10 basic equipment
2-speed Dual-Shift gear with through-drive, Walterscheid
drive shaft with cam-shift coupling for 1000 and 540 rpm
PTO, specially hardened quick-change Allround knife
tines mounted in „aggressive“ or „trailing“ mode, carrier
for track loosener, safety rail, height adjustable and
shock absorbing side shields, cat. II lower link attachment
(choice of cat. III).
Zirkon 10 optional equipment
Rollers from the wide LEMKEN range, mechanical lifting
rods, hitch triangle, levelling blade, track loosener, side
discs, implement front mounting system, quick-change
Allround knife tines hardfaced.
All statements, measurements and weights given represent
standards subject to continuous further development
and are therefore not binding. The weights given
always refer to standard equipped implements. We reserve
the right to change specifications.
All information, measurements and weights are subject to continuous technical further development and are therefore non obligatory. Information
regarding weights always refers to the basic model. The right is reserved to make alterations.
LEMKEN GmbH & Co. KG
Weseler Str. 5, D-46519 Alpen · Postfach 11 60, D-46515 Alpen
Telefon (+49) 28 02 / 81-0 · Fax (+49) 28 02 / 81-2 20
E-Mail: lemken@lemken.com · Internet: www.lemken.com
FS. Völcker · 06/04 · 175 0190/GB