Craftsman Wall Cabinet - The Taunton Press
Craftsman Wall Cabinet - The Taunton Press
Craftsman Wall Cabinet - The Taunton Press
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
14 ¾ in.<br />
5 1/8 in.<br />
11 ¾ in.<br />
4 5/16 in.<br />
square<br />
<strong>Craftsman</strong> <strong>Wall</strong> <strong>Cabinet</strong><br />
by Ian Ingersoll<br />
31 ½ in.<br />
5 1/8 in.<br />
8 ¾ in.<br />
½ in.<br />
Top, 1 in. x 8 ¾ x 14 ¾ in.<br />
8 in.<br />
12 ¾ in.<br />
11 ¾ in.<br />
Groove, ½ in. x ¼ in.,<br />
houses back.<br />
Rabbet, ½ in x ¼ in.,<br />
accepts subtop.<br />
A Drawer that Tilts Out<br />
A small rabbet accepts a bead<br />
that allows the drawer to tilt.<br />
Subtop<br />
Dadoes, ½ x ¼ in.,<br />
accept shelves.<br />
Pivoting stop keeps<br />
drawer from falling<br />
out of case.<br />
Side, ¾ in. x 6 in.<br />
x 29 ½ in.<br />
Drawer<br />
5 in. deep<br />
Shelf, ½ in. x<br />
5 ¼ in. x 10 ¾ in.<br />
Drawer stop, 3/8 in.<br />
x 3/8 in. x 1 ¼ in.<br />
Radius,<br />
8 in.<br />
Back, ½ in. x<br />
10 ¾ in. x 29 ½ in.<br />
Brad, 1 ¼ in.<br />
Notch, 1/2 in. wide,<br />
accepts drawer stop.<br />
Front rabbet, ¼ in. x<br />
5/8 in., accepts side<br />
Drawer Front Section<br />
Bottom, 1 in. x 7 ¼ in.<br />
x 12 ¾ in.<br />
Groove, ¼ in. x ¼ in.<br />
and set back 3/8 in.<br />
accepts pivot bead<br />
on drawer front.<br />
Drawer front<br />
Hole, ¾ in. dia.<br />
Pivot bead, 1/4 in.<br />
x 1/4 in.<br />
Copyright © 2008, <strong>The</strong> <strong>Taunton</strong> <strong>Press</strong>
Molding, ¼ in. x ¼ in.,<br />
holds glass in place<br />
Glass, 1/8 in. thick<br />
Setting in Muntins and Glass<br />
Panes for the glass<br />
With two 45 º cuts on each<br />
muntin end, the muntins<br />
are laid in place, and the<br />
miters are marked on the<br />
rails and stiles.<br />
Muntin,<br />
¼ in. x<br />
5/8 in.<br />
Miter, 45 º,<br />
accepts<br />
muntin<br />
Cutting miters in the<br />
rails and stiles<br />
Use a small saw to cut<br />
miters on the door frame,<br />
which will accept the<br />
muntin ends.<br />
Stub tenon,<br />
¼ in. x ¼ in.<br />
Groove, ¼ in.,<br />
accepts door<br />
panel.<br />
Crossing the glass<br />
Add the muntins, to give<br />
the appearance of divided<br />
panes of glass. Mark the<br />
stock for a half-lap joint<br />
where the muntins cross,<br />
then cut the joint on the<br />
tablesaw.<br />
Stile, ¾ in. x 1 ¼ in.<br />
x 29 ½ in.<br />
Finishing a groove<br />
<strong>The</strong> rear wal of the groove<br />
in the stiles and rails is<br />
removed to accept glass.<br />
Rail, ¾ in. x 1 ¼ in. x 11 ¾ in.<br />
Miter, 45 º cut into<br />
rails and stiles.<br />
Door panel, ¼ in. thick.<br />
CUTLIST<br />
Component Qty. Dimensions<br />
Top 1 1 x 8 ¾ x 14 ¾<br />
Subtop 1 ½ x 5 ¼ x 10 ¾<br />
Shelf 1 ½ x 5 ¼ x 10 ¾<br />
Bottom 1 1 x 7 ¼ x 12 ¾<br />
Back 1 ½ x 10 ¾ x 29 ½<br />
Side 2 ¾ x 6 x 29 ½<br />
Door stile 2 ¾ x 1 ¼ x 29 ½<br />
Door rail 3 ¾ x 1 ¼ x 11 ¾<br />
Window muntins 2 ¼ x 5 /8 x 9 7 /8<br />
Window molding 4 ¼ x ¼ x 9 ¾<br />
Drawer front 1 5/8 x 9 ¾ x 8<br />
Drawer side 2 5/8 x 4 x 8<br />
Drawer back 1 5/8 x 9 ¾ x 8<br />
Drawer bottom 1 ¼ x 4 ¼ x 9<br />
Door panel 1 1/4 x 9 ¾ x 15 ¾<br />
Drawer stop 1 3/8 x 3 /8 x 1 ¼