Appendix
Appendix Appendix
13. Function Code List Communication Control type: Available/ address Not available Fcode 485 Link number number Function name Function directory name Setting range PG LES VF SM 27 : Synchronization completion signal (SY-C) o x x x 28 : Lifetime alarm (LIFE) o o o o 29 : Under acceleration (U-ACC) o o o o 30 : Under deceleration (U-DEC) o o o o 31 : Inverter overload early warning (INV-OL) o o o o 32 : Motor overheat early warning (M-OH) o o o o 33 : Motor overload early warning (M-OL) o o o o 34 : DB overload early warning (DB-OL) o o x o 35 : Link transmission error (LK-ERR) o o o o 36 : load adaptive control under limiting (ANL) o x x x 37 : load adaptive control under calculation (ANC) o x x x 38 : Analog torque bias hold (TBH) o o x o 39 to 47 : Option DO1 to 9 (O-DO1 to O-DO9) o o o o e16 110h 86 h Y2 terminal function 0 to 2 to 47 (Refer to Y1 function selection.) 58 o o o o o o o o e17 111h 87 h Y3 terminal function 0 to 3 to 47 (Refer to Y1 function selection.) 58 o o o o o o o o e18 112h 88 h Y4 terminal function 0 to 4 to 47 (Refer to Y1 function selection.) 58 o o o o o o o o e19 113h 89 h Y5 terminal function 0 to 14 to 47 (Refer to Y1 function selection.) 58 o o o o o o o o e20 114h 8A h Y11 terminal function 0 to 26 to 47 (Refer to Y1 function selection.) 58 o o o o o o o o e21 115h 8B h Y12 terminal function 0 to 26 to 47 (Refer to Y1 function selection.) 58 o o o o o o o o e22 116h 8C h Y13 terminal function 0 to 26 to 47 (Refer to Y1 function selection.) 58 o o o o o o o o e23 117h 8D h Y14 terminal function 0 to 26 to 47 (Refer to Y1 function selection.) 58 o o o o o o o o e24 118h 8E h Y15 terminal function 0 to 26 to 47 (Refer to Y1 function selection.) 58 o o o o o o o o e25 119h 8F h Y16 terminal function 0 to 26 to 47 (Refer to Y1 function selection.) 58 o o o o o o o o e26 11Ah 90 h Y17 terminal function 0 to 26 to 47 (Refer to Y1 function selection.) 58 o o o o o o o o e27 11Bh 91 h Y18 terminal function 0 to 26 to 47 (Refer to Y1 function selection.) 58 o o o o o o o o e28 11Ch Y terminal function 0000 to 001F 36 o o o o o o o o normally open/close Setting of normal state of Y1to Y4,RY. 0 : Normally open 1 : Normally close e29 11Dh 92 h PG pulse output selection e30 11Eh Motor OH protection Motor OH protection (temperature) e31 11Fh M-OH early warning (temperature) e32 120h CD h M1-M3 (operation level PTC) You can change the setting of a function indicated by during operation. You should stop operation to change the setting of other functions. 0 to 9 0 : No dividing 1 : 1/2 2 : 1/4 3 : 1/8 4 : 1/16 5 : 1/32 6 : 1/64 0 to 6 : Internal PG inputs are output after being divided. 7 : Pulse oscillation mode (A/B 90° phase difference signal) Internal speed reference is output after pulse conversion. 8 : PG (PD) Pulse inputs for position encoder are directly output. 9 : PG (PR) Pulse inputs for position command are directly output. 100 to 150 to 200 ℃ It is effective when NTC thermistor is used with selected motor (M1,M2). 50 to 75 to 200 ℃ It is effective when NTC thermistor is used with selected motor (M1,M2). 13-9 92 o o o o x x o o 0 o o o o o o o o 0 o o o o o o o o 0.00 to 1.60 to 5.00 V 3 o o o o o o o o e33 121h INV-OL early warning 25 to 90 to 100 % 0 o o o o o o o o e34 122h M-OL early warning 25 to 90 to 100 % 0 o o o o o o o o e35 123h DB overload protection 0 to 10 to 100 % 0 o o o o o x o o e36 124h DB-OL early warning 0 to 80 to 100 % 0 o o o o o x o o e37 125h DB thermal time constant 0 to 100 to 1000 s 0 o o o o o x o o Type Copy Save all Initialization Lifting machine Underline indicates a factory setting.
Communication Control type: Available/ address Not available Fcode 485 Link number number Function name Function directory name Setting range PG LES VF SM e38 126h 93 h Speed detection Speed detection method 000 to 111 9 o o o o o x o o method (N-DT1) (N-DT2) (N-DT3) 0 : Detected speed 1 : Speed reference Only reference values are effective under VF control. e39 127h 94 h N-DT1 Level 0 to 1500 to 24000 r/min 0 o o o o o o o o e40 128h 95 h N-DT2 Level -24000 to 1500 to 24000 r/min 5 o o o o o o o o e41 129h 96 h N-DT3 Level -24000 to 1500 to 24000 r/min 5 o o o o o o o o e42 12Ah 97 h N-AR detection width 1.0 to 3.0 to 20.0 % 2 o o o o o x o o e43 12Bh 98 h N-AG detection width 1.0 to 3.0 to 20.0 % 2 o o o o o x o o e44 12Ch 99 h N-AG off-delay timer 0.000 to 0.100 to 1.000 s 4 o o o o o x o o e45 12Dh 9A h Speed disagreement alarm You can change the setting of a function indicated by during operation. You should stop operation to change the setting of other functions. 0 to 21 Place of 1: Speed disagreement alarm (Er9) 0: Not used 1: Used Place of 10: Lin phase loss detection 0: Level without DCR 1: Level with DCR 2: For manufacturer (Do not specify.) 13-10 9 o o o o o x o o e46 12Eh 9B h Torque detection level 1 0 to 30 to 300 % When the V/F control is used, the calculation value is set. 16 o o o o o o o o e47 12Fh 9C h Torque detection level 2 0 to 30 to 300 % When the V/F control is used, the calculation value is set. 16 o o o o o o o o e48 130h 9D h Magnetic flux detection level 10 to 100 % 16 o o o o o x x o e49 131h Ai function selection Ai1 function selection 0 to 18 59 o o o o o o o o 0 : Input sigunal off (OFF) o o o o 1 : Auxiliary speed setting 1 (before ramp function) (AUX-N1) ±10V/±Nmax o o o o 2 : Auxiliary speed setting 2 (after ramp function) (AUX-N2) ±10V/±Nmax o o o o 3 : Torque limiter level 1 (TL-REF1) ±10V/±150% o o x o 4 : Torque limiter level 2 (TL-REF2) ±10V/±150% o o x o 5 : Torque bias level (TB-REF) ±10V/±150% o o x o 6 : Torque reference (before limit function) (T-REF) ±10V/±150% o o x o 7 : Torque current reference (IT-REF) ±10V/±150% 8 : Creep speed 1 for UP/DOWN control (CRP-N1) ±10V/±Nmax 9 : Creep speed 2 for UP/DOWN control (CRP-N2) ±10V/±Nmax 10 : Magnetic flux reference (MF-REF) ±10V/±100% o o x o o o o o o o o o o o x x 11 : Detected line speed (LINE-N) ±10V/±Nmax o o o o 12 : Motor temperature feedback (M-TMP) +10V/ 200°C o o o o 13 : Speed override (N-OR) ±10V/±50% o o o o 14 : Universal Ai (U-AI) ±10V/±4000 (h) o o o o 15 : PID feedback (PID-FB) ±10V/±20000 (d) o o o o 16 : PID reference value (PID-REF) ±10V/±20000 (d) o o o o 17 : PID correction gain (PID-G) ±10V/±4000 (h) o o o o 18 : Option Ai (O-AI) ±10V/±7FFF (h) o o o o e50 132h Ai2 function selection 0 to 18 (Refer to Ai1 function selection.) 59 o o o o o o o o e51 133h Ai3 function selection 0 to 18 (Refer to Ai1 function selection.) (Displayed when the AIO option is installed.) e52 134h Ai4 function selection 0 to 18 (Refer to Ai1 function selection.) (Displayed when the AIO option is installed.) Type Copy Save all Initialization Lifting machine 59 o o o o o o o x 59 o o o o o o o x Underline indicates a factory setting.
- Page 2 and 3: 12. Operation Data 12.1 Frequency R
- Page 4 and 5: 12. Operation Data 12.5 Impact load
- Page 6 and 7: 12. Operation Data 12.8 Speed-torqu
- Page 8: 12. Operation Data 12.11 Comparison
- Page 11 and 12: 13.2 Function Code List 13.2.1 Func
- Page 13 and 14: Communication Control type: Availab
- Page 15 and 16: Communication Control type: Availab
- Page 17: Communication Control type: Availab
- Page 21 and 22: Communication address Fcode Functio
- Page 23 and 24: Fcode Communication address 485 num
- Page 25 and 26: H: High Performance Functions Commu
- Page 27 and 28: Communication address Fcode 485 Lin
- Page 29 and 30: Communication address Fcode 485 Lin
- Page 31 and 32: Communication address Fcode 485 Lin
- Page 33 and 34: Communication address Fcode Functio
- Page 35 and 36: 13.3 Function Code List Dedicated t
- Page 37 and 38: 485 Min increment Unit Type number
- Page 39 and 40: Type [14]: Cause of alarm 15 12 8 7
- Page 41 and 42: Type [29]: Inverter model (common t
- Page 43 and 44: Type [35]: X function normally open
- Page 46 and 47: 14. Replacement Data When replacing
- Page 48 and 49: 14. Replacement Data 14.2.2 Replaci
- Page 50 and 51: 14. Replacement Data 14.3 Terminal
- Page 52 and 53: 14. Replacement Data 14.3.2 Replaci
- Page 54 and 55: 14. Replacement Data 14.3.3 Replaci
- Page 56 and 57: 14. Replacement Data 14.4 Terminal
- Page 58 and 59: 14. Replacement Data Cat- ego- ry T
- Page 60 and 61: 14. Replacement Data Cat- ego- ry A
- Page 62 and 63: 14. Replacement Data 14.4.3 Replaci
- Page 64 and 65: 14. Replacement Data � Difference
- Page 66 and 67: 14. Replacement Data FRENIC5000 VG5
Communication<br />
Control type: Available/<br />
address<br />
Not available<br />
Fcode<br />
485 Link<br />
number number<br />
Function name Function directory name<br />
Setting range<br />
PG LES VF SM<br />
e38 126h 93 h Speed detection Speed detection method 000 to 111<br />
9 o o o o o x o o<br />
method<br />
(N-DT1) (N-DT2) (N-DT3)<br />
0 : Detected speed<br />
1 : Speed reference<br />
Only reference values are effective under VF<br />
control.<br />
e39 127h 94 h N-DT1 Level 0 to 1500 to 24000 r/min 0 o o o o o o o o<br />
e40 128h 95 h N-DT2 Level -24000 to 1500 to 24000 r/min 5 o o o o o o o o<br />
e41 129h 96 h N-DT3 Level -24000 to 1500 to 24000 r/min 5 o o o o o o o o<br />
e42 12Ah 97 h N-AR detection width 1.0 to 3.0 to 20.0 % 2 o o o o o x o o<br />
e43 12Bh 98 h N-AG detection width 1.0 to 3.0 to 20.0 % 2 o o o o o x o o<br />
e44 12Ch 99 h N-AG off-delay timer 0.000 to 0.100 to 1.000 s 4 o o o o o x o o<br />
e45 12Dh 9A h Speed disagreement<br />
alarm<br />
You can change the setting of a function indicated by during operation.<br />
You should stop operation to change the setting of other functions.<br />
0 to 21<br />
Place of 1: Speed disagreement alarm (Er9)<br />
0: Not used<br />
1: Used<br />
Place of 10: Lin phase loss detection<br />
0: Level without DCR<br />
1: Level with DCR<br />
2: For manufacturer (Do not specify.)<br />
13-10<br />
9 o o o o o x o o<br />
e46 12Eh 9B h Torque detection level 1 0 to 30 to 300 %<br />
When the V/F control is used, the calculation value<br />
is set.<br />
16 o o o o o o o o<br />
e47 12Fh 9C h Torque detection level 2 0 to 30 to 300 %<br />
When the V/F control is used, the calculation value<br />
is set.<br />
16 o o o o o o o o<br />
e48 130h 9D h Magnetic flux detection<br />
level<br />
10 to 100 % 16 o o o o o x x o<br />
e49 131h Ai function selection Ai1 function selection 0 to 18 59 o o o o o o o o<br />
0 : Input sigunal off (OFF) o o o o<br />
1 : Auxiliary speed setting 1 (before ramp function)<br />
(AUX-N1) ±10V/±Nmax<br />
o o o o<br />
2 : Auxiliary speed setting 2 (after ramp function)<br />
(AUX-N2) ±10V/±Nmax<br />
o o o o<br />
3 : Torque limiter level 1 (TL-REF1) ±10V/±150% o o x o<br />
4 : Torque limiter level 2 (TL-REF2) ±10V/±150% o o x o<br />
5 : Torque bias level (TB-REF) ±10V/±150% o o x o<br />
6 : Torque reference (before limit function)<br />
(T-REF) ±10V/±150%<br />
o o x o<br />
7 : Torque current reference (IT-REF)<br />
±10V/±150%<br />
8 : Creep speed 1 for UP/DOWN control (CRP-N1)<br />
±10V/±Nmax<br />
9 : Creep speed 2 for UP/DOWN control (CRP-N2)<br />
±10V/±Nmax<br />
10 : Magnetic flux reference (MF-REF)<br />
±10V/±100%<br />
o o x o<br />
o o o o<br />
o o o o<br />
o o x x<br />
11 : Detected line speed (LINE-N) ±10V/±Nmax o o o o<br />
12 : Motor temperature feedback (M-TMP)<br />
+10V/ 200°C<br />
o o o o<br />
13 : Speed override (N-OR) ±10V/±50% o o o o<br />
14 : Universal Ai (U-AI) ±10V/±4000 (h) o o o o<br />
15 : PID feedback (PID-FB) ±10V/±20000 (d) o o o o<br />
16 : PID reference value (PID-REF)<br />
±10V/±20000 (d)<br />
o o o o<br />
17 : PID correction gain (PID-G) ±10V/±4000 (h) o o o o<br />
18 : Option Ai (O-AI) ±10V/±7FFF (h) o o o o<br />
e50 132h Ai2 function selection 0 to 18 (Refer to Ai1 function selection.) 59 o o o o o o o o<br />
e51 133h Ai3 function selection 0 to 18 (Refer to Ai1 function selection.)<br />
(Displayed when the AIO option is installed.)<br />
e52 134h Ai4 function selection 0 to 18 (Refer to Ai1 function selection.)<br />
(Displayed when the AIO option is installed.)<br />
Type<br />
Copy<br />
Save all<br />
Initialization<br />
Lifting<br />
machine<br />
59 o o o o o o o x<br />
59 o o o o o o o x<br />
Underline indicates a factory setting.
Change language