099000 Paints & Coatings

COATESVILLE AREA SCHOOL DISTRICT SECURITY MODIFICATIONS - #1245
SECTION 099000
PAINTS AND COATINGS
PART 1 - GENERAL
1.1 SECTION INCLUDES
A. Surface preparation and field application of paints and coatings.
1.2 RELATED SECTIONS
A. Section 092300 - Gypsum Plaster.
B. Section 092900 - Gypsum Board Systems.
B. Section 130650 - Bullet Resistant Steel Frames.
C. Section 130700 - Bullet Resistant Steel Doors.
1.3 ENVIRONMENTAL REQUIREMENTS
A. Comply with all applicable codes and regulations for handling, storage, and application of
finish materials.
B. Store and apply materials in environmental conditions required by manufacturer's
instructions.
C. Final coats of paint shall be installed under permanent lighting conditions.
1.4 REFERENCES
A. ASTM D16 - Standard Terminology Relating to Paint, Varnish, Lacquer, and Related
Products.
B. NPCA - Guide to U.S. Government Paint Specifications; National Paint and Coatings
Association.
C. SSPC - Steel Structures Painting Manual; Steel Structures Painting Council.
1.5 REGULATORY REQUIREMENTS
A. Conform to ASTM E 84 or ASTM E119 and applicable IBC Code for fire rated assemblies:
Provide Class A finishes with Smoke development rating less than 450.
1.6 SUBMITTALS
A. Submit under provisions of Section 013300 - Submittals
B. Product Data: Provide Data indicating coating materials, manufacturer’s specifications and
installation instructions. Cross-reference coating system method and application to each
substrate.
1.7 DELIVERY, STORAGE, AND HANDLING
A. Deliver, store, protect and handle products to the Project site under provisions of Section
016000.
PAINTS AND COATINGS 099000-1

COATESVILLE AREA SCHOOL DISTRICT SECURITY MODIFICATIONS - #1245
B. Store materials in a dry, secure area.
C. Maintain temperature of 50 - 90 deg F.
D. Keep products away from fire or open flame.
PART 2 - PRODUCTS
2.1 MANUFACTURERS
A. Paint Manufacturers:
1. M.A. Bruder. (MAB)
2. Benjamin Moore & Co.
3. Finneran & Haley
4. Sherwin-Williams
5. PPG
6. Duron
B. Substitutions: Under provisions of Section 016000.
2.2 MATERIALS
A. Coatings: Ready mixed, except field catalyzed coatings, of manufacturer’s best quality of
good flow and brushing properties, capable of drying or curing free of streaks, yellowing or
sags.
B. Accessory Materials: Linseed oil, shellac, turpentine, paint thinners and other materials
required to achieve the finishes specified.
C. Provide highest quality, best grade paint for each type of paint system listed, from one
manufacturer listed above. Primer and finish shall be from same manufacturer.
D. Finish Materials: Conform to applicable code for flame/smoke rating requirements.
E. Paints shall achieve the following minimum dry film thickness per coat:
1. Primers:
a. Primers on Steel: 1.5 mils
2. Finishes:
a. Finishes on Steel: 1.5 mils
PART 3 - EXECUTION
3.1 EXAMINATION AND PREPARATION
A. Verify that substrate conditions are ready to receive the Work.
B. Measure moisture content of porous surfaces using electronic moisture meter. Do not apply
finishes unless moisture content is less than 15 percent.
C. Correct minor defects and clean surfaces which affect the Work of this Section.
D. Existing Surfaces to Remain:
1. Prepare existing surfaces in manner recommended by finish coating manufacturer for
scheduled application and to insure cohesiveness and bond of new finish.
E. Metal Surfaces: Remove surface contamination and oils and wash with solvent.
1. Galvanized Surfaces: Apply coat of etching primer.
PAINTS AND COATINGS 099000-2

COATESVILLE AREA SCHOOL DISTRICT SECURITY MODIFICATIONS - #1245
3.2 APPLICATION
2. Shop Primed Metals:
a. Sand and scrape to remove loose primer and rust, hand clean, clean surfaces
with solvent.
b. Prime bare steel surfaces.
c. Test shop primer for compatibility with finished paint. If paint system is
incompatible with finish paint system provide isolating primer.
3. Uncoated Ferrous Surfaces:
a. Remove scale by wire brushing, sandblasting, clean by washing with solvent.
b. Apply treatment of phosphoric acid solution.
c. Prime paint after repairs.
4. Existing Steel: Remove metal scale and loose materials in accordance with paint
manufacturer’s recommendations follow SSPC-SP-7 Brush Blasting or SSPC-SP-3
Power Tool Cleaning.
A. Apply the Products in accordance with manufacturer's instructions.
3.3 SCHEDULE - INTERIOR SURFACES
A. General: Unless noted otherwise, paint indicated is trade name and product code for MAB
and shall serve as minimum standard quality. All manufacturers shall supply best quality
grade materials. Gloss shall be as selected by Architect.
B. Plaster, Gypsum Board:
1. Ceilings and Soffits Higher than 8'-6" AFF: Unless noted otherwise on the I.D.
Scheme.
a. One coat Rich Lux Prime Fast (037-138).
b. Two coats Rich Lux Low Lustre Latex Enamel (028 line).
2. Other Areas:
a. One coat Rich Lux Latex Sealer Undercoater (037-154).
b. Two coats Ply Tile 530 (059 line) Low Luster.
C. Wood - Painted:
1. One coat Rich Lux Sealer Undercoater (037-154).
2. Two coats Rich Lux Low Lustre Enamel (028 line).
3. Or Two coats Rich Lux Semi-Gloss Enamel (023 line).
D. Steel:
1. Doors and Borrowed Lite Frames::
a. One coat Rust-O-Lastic Anti-Corrosive Primer 073 line
b. Two coats of Rust-O-Lastic DTM (063 line/low sheen) or (043 Line /Gloss)
E. Steel - Galvanized:
1. For shop primed items repair primer damage and paint.
a. One coat Rust-O-Lastic Hydro Prime II (073-189).
b. Two coats of Rust-O-Lastic DTM (063 line/low sheen).
3.4 SCHEDULE - COLORS
A. Finish colors as indicated and selected by Architect.
END OF SECTION
PAINTS AND COATINGS 099000-3