1 - PNet - Trend
1 - PNet - Trend
1 - PNet - Trend
- No tags were found...
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
) <br />
5 JH= JA C O<br />
1,<br />
5 A HE= <br />
5<br />
<br />
<br />
1.3 Installation - Fixing (continued)<br />
6<br />
Connect Lon (continued)<br />
LonMark<br />
Device<br />
IQL<br />
Lonworks bus<br />
LINC<br />
LINC<br />
IQ Outstations<br />
IQ Outstation<br />
Normal IQ System current loop Lan cable is not<br />
recommended<br />
Do not use screened cable<br />
Cable<br />
Max<br />
bus length<br />
Max node to node<br />
B elden 85102 500<br />
m (545 yds)<br />
500 m (545 yds)<br />
IQ system<br />
TP/1/0/16/HF/200 500<br />
m (545 yds) 400 m (430 yds)<br />
(Belden 8471)<br />
U L Level IV, 22 AWG 500<br />
m (545 yds)<br />
400 m (430 yds)<br />
J Y(St) Y2 x 2 x 0.8 500<br />
m (545 yds)<br />
320 m (350 yds)<br />
TIA5268A Cat. 5,<br />
24 AWG<br />
450<br />
m (490 yds) 250 m (270 yds)<br />
Terminal size 0.5 to 2.5 mm 2 (14 to 20 AWG)<br />
If used with LPT-10 (powered bus), cable lengths differ - see “Link Power Transceiver<br />
User’s Guide (078-0105-01C)”.<br />
Connect Inputs and Outputs<br />
7<br />
If non standard strategy, follow<br />
special installation instructions and<br />
jump to section 2.1 step 14<br />
Non-standard Strategy<br />
Installation Instructions<br />
8<br />
! " #<br />
+ + <br />
+<br />
Connect Inputs<br />
Terminal size 0.5 to<br />
2.55 mm 2 (14 to<br />
20 AWG)<br />
# <br />
<br />
<br />
Sensors TB/TS, TB/TS/K, TB/TS/KE, TB/TS/KEF<br />
recommended; wire as shown below.<br />
9<br />
2<br />
! " #<br />
<br />
+ <br />
+ <br />
! " # $ % &<br />
2 1 3 6 5 4<br />
TE/TS /K /F /E<br />
Room Display Module (RD-IQL/K, /KOS,<br />
/KOSF) provides monitor and control; wired as<br />
shown below:<br />
polarity<br />
independent<br />
Note that the IQL must be<br />
correctly set up to use the<br />
RD-IQL, see section 3 step 15<br />
Note that terminal types COM and<br />
C should not be connected together<br />
Configure/Commission<br />
IQL15+/xxx Installation<br />
Instructions, TG200344 -<br />
Sheet 2<br />
+<br />
"<br />
+<br />
$ %<br />
RD-IQL<br />
<br />
Local<br />
Space<br />
Temperature<br />
Sensor<br />
! " # $ % &<br />
Auto<br />
Local Setpoint<br />
Adjust<br />
Potentiometer<br />
Off<br />
Fan Speed Select<br />
T<br />
Pushbutton<br />
or PIR input<br />
∆T<br />
Window or<br />
Alarm<br />
contact<br />
Pushbutton or PIR<br />
input type selected<br />
by configuration<br />
parameter W6<br />
PIR<br />
PIR<br />
TE/TS<br />
/ <br />
TE/TS/K<br />
/ <br />
TE/TS/KE<br />
/ <br />
TE/TS/KEF<br />
/ <br />
RD/IQL/K<br />
S / / /<br />
RD/IQL/KOS<br />
S / /<br />
RD/IQL/KOSF<br />
S S / /<br />
input included in TB or RD<br />
S separate input may be used<br />
/ Input either cannot be connected, or will be ignored<br />
Connection of separate device to input required