1 - PNet - Trend

)
5 JH= JA C O
1,
5 A HE=
5
3. Installation - Configuration (continued)
14
Check Operation - Fan Speed Select
IN3
) K J
BB
OUT1, 2, 3
#
If Occupied and Remote Fan Speed (K7) Auto
Fan Speed Switch can be provided by TB/TS/KEF or
RD-IQL/KOSF (see section 1.3 step 8)
Set up Strategy Parameters
15 if required
Use IqlTool2 (see section 2.2 step 5 ) and text
communications
For standard strategies use table below, else refer to
non-standard strategy installation instructions
Parameter
K1(V)
K2(V)
K3(V)
K4(V)
K5(V)
K6(V)
K7(V)
K8(V)
Label
Remote
Setpoint
RemoteSpaceTemp
OCC Deadbnd
Standby
Deadbnd
NOCC Deadbnd
Remote
Occ
Remote
Fan Spd
Remote
SP Offset
Function
Base
setpoint can be adjusted remotely
Used
if bound to Lon sensor, or if local sensor disconnected
Deadband
around setpoint during Occ
Deadband
around setpoint during Standby
Deadband
around setpoint during Nocc
Sets
state 0=Occ, 1=Nocc, 2=Bypass, 3=Standby
Sets
speed 0=off, 1=Low, 2=Med, 3=High, 4=Auto
Used
if bound to a Lon Sensor or if local adjust is disconnected
20 ° C
20 ° C
1 ° C
2 ° C
12 ° C
Default
0=Occupied
4=Auto
0 ° C
K15(V)
W2(S)
W3(S)
O ffset range
Defines
range of Local SP adjust pot.
S ummer Mode
Winter
(heat only) or Summer (cool only) (only used for /WR2, /WT2)
Elec
Disable
Disable
Electric Heater if set to I
2 ° C
O=Winter
O=enable Elec
W5(S)
W6(S)
W7(S)
W8(S)
L1(G)
L1(I)
L2(G)
L2(I)
Window mode
O=Pb
I=PIR
Frost
Condition
Remote
Shutdown
Window contact if set to I, alarm contact if set to O
PIR if set to I, Pushbutton if set to O
Overrides
heating to 98 % (not /AR2) if unoccupied
Shuts
off fan, and sets heat/cool to zero
Heat
Loop Gain
40
Heat
Loop Integral
Cool
Loop Gain
-40
Cool
Loop Integral
O=alarm contact
O=pushbutton
O=no frost
O=no shutdown
0 mins
0 mins
Note that any changes to the strategy parameters should immediately be followed by a write to the address
module, [text comms command, R(z=O), recommended], to commit changes to flash memory.
If used with RD-IQL (see section 1.3 step 8), the following must be configured: Local Space Temp Type
S9(Y=6), Local SP Adjust Type S10(Y=6), Local Fan Speed Type S11(Y=6), O=Pb I=PIR W6(S=O)
default, Remote Fan Spd K7(V=4) default, followed by R(z=I) to write changes to flash and reset.
Configuration for RD-IQL is facilitated by IqlTool2.
If the sensor on IN1 is to be used, leave local Space Temp Type at default, S9(Y=1). If the fan speed
switch on IN3 is to be used, leave Local Fan Speed type at default, S11 (Y=3).
If required the strategy type may be changed (e.g. /AR2 to /WR2) but
a /E strategy cannot be changed to a /AUX strategy or vice versa:
IQL15+/xxx data
sheet TA200367