Slam-Cam 1 - 264

Slam-Cam 

Page 

1 - 264 

Slam-Cam for Slam Doors. 

Locking without key or tool. 

• To a): The Teflon washer 

replaces the wave washer 

underneath the insert. 

• Used with all Quarter- 

Turns and inserts according 

to page 1-100. 

• To a1): Slam-Cam with 

free-stroke for applications 

with cylinder locks and 

handles on page 1-120 to 

1-152 and 1-154. 

• A Slam-Cam set consists 

of a cam, a spring and an 

M6x10 hex screw with 

underhead serrations and 

self securing powder dot. 

• This self securing powder 

dot is to tune / adjust the 

correct friction for the free 

stroke. The screw supplied 

with the handle is not 

required. 

• On request, latch units 

with this cam should be 

assembled by DIRAK. 

• A pre-assembled 

Quarter-Turn can be 

installed through the cutout. 

a) Slam-Cam with spring and Teflon washer 

RH version, i.e. hinges on RH side 200-9605 

LH version, i.e. hinges on LH side 200-9606 

Additional dimensions on request. 

a1) Slam-Cam with free-stroke (see description right side) 

with spring and hex screw 

RH version, i.e. hinges on RH side 200-9607 

LH version, i.e. hinges on LH side 200-9608 

b) Housings and inserts on page 1-100, 1-105, 1-107 or 1-110 

b1) Handles and cylinder locks on page 1-120 to 1-152 and 1-154 

• Material: 

a) 

• Slam-Cam: zinc die, 

chrome plated 

• Spring: steel, zinc plated 

• Washer: Teflon 

D 28/08/01 

A 10/17/03 

© copyright by DIRAK / Germany

Quarter-Turn, Screw-in Type 

Optional: Water- and dust-tight according to IP65 

Page 

1 - 100 

a) Housing with nut N 

grounding/earthing nut EN 

nut and grounding clip NEC 

zinc die, chrome plated with N 200-9001 

with EN 200-9002 

with NEC 200-9062 

zinc die, black with N 200-9048 

with EN 200-9049 

with NEC 200-9063 

PA black with N 200-9003 

with NEC 200-9004 

Further housings on page 1-105. 

Housings with extended bodies on page 1-110. 

Optional: 

Water- and dust tight according to IP65 by: 

d) O-Ring 200-1001 

e) Flat external seal 200-0901 

For IP66/67 use additional O-Ring 200-1002 

h) Assembling without O-Ring 200-0001 

with O-Ring 200-0002 

i) Assembling cam 90° to Wing knob: 

without O-Ring 200-0019 

with O-Ring 200-0021 

b) Inserts/ Knobs zinc die zinc die PA black 

refer to page 1-002 chrome pl. black zinc die core 

Square 6mm 200-9101 200-9127 - 

Square 7mm 200-9102 200-9116 - 

Square 8mm 200-9103 200-9128 - 

Square 8mm slotted 200-9111 - - 

Triangular 6.5 CNOMO 200-9106 - - 

Triangular 7mm 200-9104 200-9129 - 

Triangular 8mm 200-9105 200-9130 - 

Triangular 9mm EDF 200-9147 200-9148 - 

Double bit 3mm pin 200-9107 200-9131 200-9117 

Double bit 5mm pin 200-9108 200-9132 200-9118 

Socket head 6mm 200-9142 - - 

Socket head 10mm 200-9112 - - 

Socket head 5/16“ 3mm Pin 200-9172 200-9178 - 

Square socket 6mm 200-9166 - - 



Daimler Benz type 200-9109 200-9133 - 

Slotted 2mm, 4mm deep 200-9113 200-9143 200-9126 

Crown type 200-9110 - - 

Slotted recessed coinproof 200-9164 200-9169 - 

GDF 10x5mm France 200-9141 - - 

Crescent Czech 200-9154 - - 

Hex 7/16“ 200-9171 100-9127 - 

Hex 10mm 200-9185 - - 

b1) Star knob 50 - - 200-9114 

b2) Wing knob - - 200-9115 

b3) Wing knob - 100-9115 - 

Wing knob b3) only for housing 28. 

Other versions on request! Please refer to page 1-002. 

Quarter-Turn with 90° turn, RH or LH application. 

The Quarter-Turn consists of three basic components which can be 

combined to suit your application. 

On request parts can be assembled by DIRAK. 

A pre-assembled Quarter-Turn can be installed through the cutout. 

Key (PA, black or zinc die) please refer to page 6-100. 

c) Cams 

(steel, Zinc plated) 

H 

mm / inch 

2 / 0.079 200-0402 - - 

4 / 0.157 200-0404 - 200-9504 

6 / 0.236 200-0406 200-0606 200-9506 

8 / 0.315 200-0408 200-0608 200-9508 

10 / 0.394 200-0410 200-0610 200-9510 

13 / 0.512 200-0413 200-0613 200-9513 

14 / 0.551 200-0414 200-0614 200-9514 

16 / 0.630 200-0416 200-0616 200-9516 

18 / 0.709 200-0418 200-0618 200-9518 

20 / 0.787 200-0420 200-0620 200-9520 

22 / 0.866 200-0422 200-0622 200-9522 

24 / 0.945 200-0424 200-0624 200-9524 

25 / 0.984 200-0425 200-0625 200-9525 

26 / 1.024 200-0426 200-0626 200-9526 

28 / 1.102 200-0428 200-0628 200-9528 

30 / 1.181 200-0430 200-0630 200-9530 

32 / 1.260 200-0432 - 200-9532 

34 / 1.339 200-0434 - 200-9534 

35 / 1.378 200-0435 200-0635 200-9535 

36 / 1.417 200-0436 - 200-9536 

38 / 1.496 200-0438 200-0638 200-9538 

40 / 1.575 200-0440 200-0640 200-9540 

42 / 1.654 200-0442 200-0642 200-9542 

44 / 1.732 200-0444 200-0644 200-9544 

45 / 1.772 200-0445 - 200-9545 

47 / 1.850 200-0447 - 200-9547 

50 / 1.969 200-0450 - 200-9550 

53 / 2.087 200-0453 - - 

55 / 2.165 200-0455 - - 

2-point cam 200-9599 

Cam with ramp H=18 and L=25 200-5118 

Hooked cam on page 1-260. 

Other dimensions of cams on page 1-262. 

The accessories shown 

below are drawn on 

pages 1-270, 1-275 or 

6-100. 

D 02/10/03 

A 8/2/04 

Refer to page 1-275 

Part No. 200-4703.03 

Part No. 200-4101 

or 200-4103 

Part No. 200-4601 

Part No. 200-4701 

Refer to page 6-100 

© copyright by DIRAK / Germany 


1‐060 Snap/Push‐Lock 

Snap/Push lock with slam function, nut 

or clip fixing. 

• Released by pushing. 

• Lager lockable version see page 05.7 

or 05.8. 

Material: 

Version A: 

• Snap‐Lock: 

zinc die, chrome plated 

a) 

• Fingerpull: 

PA, black 

Version B: 



Latches 

04/12/2010 


Snap/Push lock Version A Part No. see page 

A for 14,1mm / 0.555 252‐9001 

Please order separately: 

a) Finger pull 

220‐1301 

(only for version A) 

DIRAK GmbH Königsfelder Str. 1 D-58256 Ennepetal 

Phone:+49 (0) 2333.837-0 Fax: +49 (0) 2333.837-100 www.dirak.com 

Snap/Push lock Version B 

B1 with fixing clip 252‐9003 

B2 with nut M15x1 252‐9004 

b) i.e. Rectangular Profiles 209‐0301 07.9 

05.6

1‐068 Pull Latch Handle 

The Pull Latch Handle is used by 19“ 

engineering for locking insertions. 

• The completely pre-assembled unit is 

fastened by a countersunk screw M4. 

• LH and RH application. 

• When inserting the plug-in unit the 

free running slam hook latches into 

the appropriate cutout and locks the 

plug-in unit with the frame. 

• Drawing at the handle unlocks the 

plug-in unit and it can be pulled out by 

the handle. 

Material: 

• Housing and handle: 

zinc die, matt chrome plated. 

• Spring for insert: 

spring steel 

• Hook: 

sintered steel, zinc plated 



04/12/2010 


Latches 

Part No. 

Pull Latch Handle 280‐9101 

The countersunk screw is not included. 

05.9

1‐069SL Pull Latch Handle SNAP‐LINE 

Snap-Line 

The pull latch handle is used by 19“ 

engineering for locking insertions. 

• The completely pre-assembled 

Drawer Latch Handle is installed by 

a simple push into the appropriate 

cutout. 

• RH and LH application. 

• When inserting the plug-in unit the 

free running slam hook latches into 

the appropriate cutout and locks the 

plug-in unit with the frame. 

• By tilting the handle, the hook is 

withdrawn from the cutout and the 

plug-in unit can be pulled out. 

• Attention: The bulge in the cutout 

is always opposite of the bolt. This 

cutout guarantees a unique and 

constant fitting. 

Material: 

• Housing and handle: 

zinc die, matt chrome plated. 

• Spring for insert: 

spring steel 

• Snap wedges: 


• Hook: 




04/12/2010 


clamping range s Part No. 

Pull Latch Handle 0,8 ‐ 1,0 480‐9002.00‐00810 

1,1 ‐ 1,3 480‐9002.00‐01113 

1,4 ‐ 1,6 480‐9002.00‐01416 

Other s ‐ dimension on request! 

01.34

1‐250 Pull and Lock Hook 

with compression 

Pull and lock hook with compression 

• 5mm compression/pulling distance. 

• With 90° stroke. 

• Vibration-proof. 

• Latching direction is always clockwise. 

• The extremely positive torque ratio 

allows for controlling this hook-latch 

by a cylinder latch. 

• Very suitable for applications on 19" 

racks and sliding doors. 

• This device can be operated by all 

Quarter Turns or handles on page 

02.26, 02.37 to 02.51. 

Material: 

a) 

• Pull and lock hook 

steel, zinc plated 

b) 

• Weld‐on pin: 


c) 

• Line‐up fork: 


Latches 

04/12/2010 


Version Part No. see page 

a) Pull and lock hook 200‐9602 



b) Weld‐on pin for pull‐and‐lock hook 200‐3704 


c) Line‐up fork 200‐3703 

d) Housings and inserts or handles 02.26, 02.37 

e) e.g. Clip‐on profiles 209‐0302 07.9 

05.12

1-300 Slam-Latch 

Slam-latch for doors and panels. 

• Can be opened by key or handle. 

• The slam-latch is screwed onto the 

latch support, which is either screwed 

or, in case of heavy application, 

welded to the door. 

• If assembled without insert it can be 

opened with tapered square key. 

• The slam bolt has a slam feature. 

Material: 

a) 

• Housing: 


• Bolt: 

zinc die, zinc plated 

b) 

• Lock support: 




04/12/2010 


Quarter-Turn 

Part No. see page 

a) Slam-latch 229-9101 

b) Lock support 229-0501 

c) Housing with nut e.g. 200-9005 02.26 

d) Insert 02.34 

Optional: 

e) T-Handle 02.44 

e2) L-Handle 02.48 

e3) Wing handle 02.39 

Fitting hardware 09.4 

02.63

1-415 Rod Latch 

for sliding doors 

Hooked cam latch for sliding doors. 

• The cam has a slam feature. 

Material: 

a) 

• Latch: 


• Cam: 


• Plug: 

PE, black 

b) 

• Lock support: 




04/12/2010 


Quarter-Turn 

a) Hooked Cam Latch Hook straight Hook curved see page 

RH 235-9015 235-9017 

LH 235-9016 235-9018 

b) Latch support h in mm / inch H in mm / inch 

10 / 0.394 20 / 0.787 235-1001 - 

16 / 0.630 26 / 1.024 235-1002 - 

10 / 0.394 42 / 1.654 - 235-1001 

16 / 0.630 48 / 1.890 - 235-1002 

c) Insert and escutcheon 02.64 

d) T- and L-Handle 02.74 

e) Swinghandle 03.21 

02.73

1‐500 Snap‐Lock L30 

The spring loaded cam of this slam-lock 

is operated by the key. 

• Lock is supplied with nut and wide 

stabilizing washer underneath nut. 

Material: 



• Washer: 


• Nut: 




04/12/2010 


Latches 

Snap‐lock 

Part No. 

keyed alike DIRAK D0205 264‐9102 

keyed different/mixed 264‐9101 

All locks supplied with two keys. 

05.7

www.dirak.com 

1-501 Snap-Lock L31.5/36.5 

Slam-lock in two different 

versions. 

. Version A: 

The spring loaded cam is 

operated by the key 

. Version B: 

The spring loaded cam is 

operated by a lockable 

push-button. 

Material for both versions: 

. Slam-lock: zinc die, 

chrome plated 

. Nut: zinc die 

Length of body L 31.5 36.5 

Door-thickness Ts max. 10 15 

Latching distance H 20 25 

A Slam-lock Key controlled 

with plain/grounding/earthing nut 

keyed alike DIRAK D0205 264-9002 264-9004 

keyed different/mixed 264-9001 264-9003 

B Slam-lock Push-button controlled 

with plain/grounding/earthing nut 

non locking 264-9009 - 

keyed alike DIRAK D0205 264-9006 264-9008 

keyed different/mixed 264-9005 264-9007 

All locks supplied with 2 keys. 

Optional for both versions: 

a) Finger pull see product system 1-270 200-4703.03 

By using a finger pull the dimensions Ts and H decreases by 2mm! 

12/15/08

Snap-Lock 

low construction 

clip-in 

Page 

6 - 122 

Snap-lock, clip-in for 

door-thickness 0.8mm to 

2.3mm (0.031 to 0.091). 

• This non-corrosive closing 

device is especially suitable 

for latching of doors and 

lids. 

• When the latch is released 

and in its final position a 

finger-tip grip becomes 

accessible to facilitate 

opening the door. 

Material: 

• Bolt and housing: 

PA, different colors 

• Spring: stainless steel 

color 

Part No. 

complete black 282-9001 

complete grey RAL 7035 282-9002 

complete red RAL 3020 282-9003 

housing black, bolt red 282-8001 

Additional colors and color combinations on request. 

D 06/01/00 

A 3/17/03 


6‐125SL Slam Latch PrA SNAP‐LINE 

PICCOLO, Flush doors 

Just slightly protruding slam latch. 

• Field of application: latching small 

door or panels. 

• To release: after unlocking, just push 

the upper, clearly marked part of the 

handle. The lower part then can be 

pulled-out and this disengages the 

spring loaded slam-bolt. 

• The spring-loaded slam bolt has a 

free-stroke, allowing slaming of closed 

and locked handles. 

• Installation: 

• Enter slam-side into the cutout first 

and then snap-in the unit. 

Material: 

• Housing, Handle and Slam‐bolt: 

PA, black 

• Cam: 


• Pin: 


• Snap wedges: 

sintered steel 

04/12/2010 


Snap-Line 



with cylinder with cylinder without cylinder 

clamping range s WITHOUT key WITH 2 keys and ring (blind plug) 

1,2 ‐ 1,7 482‐9001.00‐00015 482‐9002.00‐00015 482‐9003.00‐00015 

1,7 ‐ 2,2 482‐9001.00.00020 482‐9002.00‐00020 482‐9003.00‐00020 

2,2 ‐ 2,7 482‐9001.00‐00025 482‐9002.00‐00025 482‐9003.00‐00025 

2 keys and ring 205‐9530.00‐23211 ‐ ‐ 

Other s ‐ dimension on request! 

01.37

6‐127 Slam‐Latch 

flush 

Clip-in low profile Slam-Latch for doors 

and panels with a sheet metal thickness 

of 1.5 to 2 mm. 

• This Slam-Latch is mainly designed 

for ligth duty, applications: e.g. panels 

for electrical enclosures, A/C and air 

treatment enclosures. 

• The completely pre-assembled latch 

is slided into the cutout and pushed 

down by hand into its final position. 

• Weight: 

without cylinder: 33 gram 

with cylinder:46 gram 

Material: 

• Slam‐Latch, cpl.: 

PA, black 

• Leg spring: 

stainless steel 

• Spring for slam: 

spring steel 



Latches 

04/12/2010 


05.20

6‐127 Slam‐Latch 

flush 



04/12/2010 


Latches 

Slam‐Latch 

clamping range (S) 

from 1.5 (0.059) to 

2mm (0.079) 

non locking 282‐9501 

keyed alike DIRAK 1333* 282‐9502 

keyed different/mixed* 282‐9503 

* with stainless dust‐shutter 

05.21

www.dirak.com 

6-130 Dual Ball Catch 

Material: 

. Ball catch and 

counterpart: brass or 

brass, chrome plated 

. 

Spring: stainless steel 

Ball: stainless steel 

chrome Ball catch Counterpart Assembly 

brass plated a1 b1 c1 d1 e1 f1 a2 b2 c2 d2 e2 f2 g1 g2 h 

263-9001 263-9007 44 8.0 35.0 3.5 9.4 2.0 24.7 6.6 15.2 3.5 9.8 1.7 11.8 9.7 9.9 

263-9002 263-9008 49 8.8 39.8 3.8 10.6 2.0 28.8 7.6 19.8 3.8 11.2 2.0 13.2 10.8 10.0 

263-9003 263-9009 59.8 11.2 49.8 4.8 13.2 2.4 34.8 9.2 24 4.8 13.5 2.2 15.9 13.4 12.9 

263-9004 263-9010 68.4 13.0 58.0 4.8 15.0 2.4 40.2 12 30 4.8 15.7 2.2 18.1 15.2 14.0 

DIRAK GmbH - Königsfelder Str. 1 - D-58256 Ennepetal - Phone: +49 (0) 2333/837-0 - Fax: +49 (0) 2333/837-100 

12/16/08 


www.dirak.com 

Slam Latch 

for aluminum profiles or flush/nested doors 

Page 

6 - 150 

The slam latch for aluminum 

profiles or flush/nested doors 

consists of two units: 

The handle part with 

slam-bolt and the frame part. 

. This frame part catches the 

slam-bolt and is also the 

limit stop for the door. 

. In this way, different profile 

widths can be connected 

with each other. 

. Gently pulling the handle 

will disengage the 

Slam-Bolt 

. A gentle push will latch the 

door. 

. The complete unit is 

fastened with 4 screws M6 

(e.g. DIN 912, not included) 

into sliding tenon nuts 

which are included. 

Slam latch chrome plated black coated 

non locking 265-9606 265-9605 

keyed alike DIRAK 1333* 265-9601 265-9602 

keyed alike DS 200* 565-9601 565-9602 

keyed different/mixed 265-9603 265-9604 

All lockable slam latches are supplied with 2 keys. 

Combined versions (chrome plated/black coated) on request. 

* With stainless dust-shutter 

Material: 

. Door- and frame housing: 

zinc die, chrome plated or 

black coated 

. Handle: zinc die, 

chrome plated or 

black coated 

. 

Bolt: zinc die, untreated 

Tenon nut: steel, 

zinc plated 

01/02/06 


DIRAK GmbH & Co. KG - Königsfelder Str. 1 - D-58256 Ennepetal - Phone: +49 (0) 2333/837-0 - Fax: +49 (0) 2333/837-100

6‐160 Compression Latch 

Lever Actuated, Flush 

For the installation, the complete latch, 

including the pre-assembled U-shaped 

fastening bracket, is installed in the 

cutout from outside. 

• By rotating the fastening screw from 

outside, the U-bracket automatically 

fastens the complete latch. 

• In the "closed" position the screw can 

not be removed. 

• The adjusting screw can also be 

used for retro-adjusting to increase or 

decrease the sealing pressure. 

• Attention: Counternut for the 

adjusting screw: The standard position 

of the counternut is underneath the 

lever. Refer to A). On Request the 

counternut can be positioned on top 

of the lever. Refer B). If B) the max 

H-dimension decreases by about 

4mm. 

• PA version see page 05.29. 

Material: 

• Compression Latch: 

zinc die, black 

Other colors on request! 



Latches 

04/12/2010 


05.32


Lever Actuated, Flush 



04/12/2010 


Latches 

Compression Latch 

H-dimension from 

3 to 24mm 

0.118 to 0.945 inch 

H-dimension from 

22 to 46mm 

0.866 to 1.811 inch 

non locking 282-9401 282-9404 

keyed alike DIRAK 1333* 282-9402 282-9405 

keyed different/mixed* 282-9403 282-9406 

* with stainless dust-shutter 


a) Screw with rubber buffer 202-1001 202-1001 

05.33


Z-Line Lever Actuated, Flush 

Clip-in, low profile Compression Latch 

for doors and panels with a sheet metal 

thickness of 1.4 to 3mm or, with a 

different housing, 3 to 3.4mm thickness. 

• This latch is mainly designed for 

light duty applications: e.g. panels 

and hatches for vehicles as well 

as for electrical enclosures, A/C 

and air treatment enclosures (glove 

compartments, maintenance panels 

etc.). 

• The completely pre-assembled latch 

is slided into the cutout in the open 

position and pushed-down into its final 

position. 

• The design of the wide hook and the 

two clips guarantee a strong and solid 

fixation in the panel. 

• The adjusting screw guarantees a 

consistent pressure to the seal and 

can be adjusted upon need. 

• Weight: without lock 40g/1.43 oz 

with lock 55g/2 oz 

Material: 

• Compression Latch: 

PA, black 

• Screw and nut: 


• Spring: 

stainless steel 



Latches 

04/12/2010 


Compression Latch 

door thickness 

from 1.4 to 3 mm 

0.055 to 0.118 

door thickness 

from 3 to 3.4 mm 

0.118 to 0.134 

non locking 282‐9408 282‐9410 

keyed alike DIRAK 1333* 282‐9407 282‐9411 

keyed different/mixed* 282‐9409 282‐9412 

* with stainless dust‐shutter 

05.34


Z-Line Lever Actuated, Flush 



04/12/2010 


Latches 

05.35

Slam-Cam 1 - 264

Create successful ePaper yourself

Delete template?

Save as template?