Performance
Performance
Performance
- No tags were found...
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
<strong>Performance</strong><br />
GAC153<br />
Exhaust heat insulation<br />
GAC150<br />
GAC173<br />
Wrapping a tubular manifold will keep engine bay heat to a minimum,<br />
reducing engine bay temperatures by up to 70%. This will benefit power in<br />
two ways; firstly it will reduce the temperature of the air going into the<br />
engine; secondly, it improves the effectiveness of the manifold by increasing<br />
gas speed due to lower gas density, increasing the scavenging effect.<br />
This race proven, asbestos free, product from Thermo-Tec is manufactured<br />
from Silica based yarns and is unaffected by oil or water, whilst withstand<br />
temperatures of up to 1000°C. As a guide to coverage a 2” x 50’ roll will<br />
cover approximately 13ft of 2” pipe. Manifold wrap is supplied in a variety<br />
of sizes, see below for details. Use Snap Straps to hold the wrap in position.<br />
Roll size (W x L) Natural Black<br />
1” x 15’ roll . . . . . . . .GAC150 . . . . .£11.95 GAC151 . . . . .£13.94<br />
2” x 15’ roll . . . . . . . .GAC152 . . . . .£19.94 GAC153 . . . . .£21.95<br />
1” x 50’ roll . . . . . . . .GAC154 . . . . .£34.96 GAC155 . . . . .£38.95<br />
2” x 50’ roll . . . . . . . .GAC156 . . . . .£58.96 GAC157 . . . . .£64.96<br />
Manifold blanket<br />
Using a manifold blanket provides excellent heat retention for exhaust manifolds<br />
and can be easily installed to both cast iron and tubular manifold. Manifold<br />
blanket should be retained with Snap Straps.<br />
Manifold blanket 4-6 cylinder . . . . . . . . . . . . . . .GAC182 . . . . .£99.95<br />
Manifold blanket V8 2 piece . . . . . . . . . . . . . . . .GAC183 . . . .£108.95<br />
Snap Straps<br />
Use Snap Straps to hold the wrap or blanket in position.<br />
Snap Strap kit 8 x 9” & 4 x 18” lengths . . . . . . . .GAC172 . . . . .£31.94<br />
Snap Strap kit 6 x 9” & 4 x 18” lengths . . . . . . . .GAC173 . . . . .£27.95<br />
Snap Strap kit 12 x 9” lengths . . . . . . . . . . . . . . .GAC174 . . . . .£29.95<br />
Snap Strap kit 6 x 18” lengths . . . . . . . . . . . . . . .GAC175 . . . . .£19.94<br />
Snap Strap kit 4 x 14” lengths . . . . . . . . . . . . . . .GAC176 . . . . . .£9.95<br />
Twin SU stainless steel heat shields<br />
These new mirror finish stainless steel heat shields not only look great they<br />
also redirect some of the heat from the exhaust manifold.<br />
Twin SU stainless steel heat shields for HS2 . . . .MST018 . . . . .£15.80<br />
Twin SU stainless steel heat shields for HS4/6 . . .MST019 . . . . .£15.80<br />
Large port manifold gasket<br />
The large ports on this gasket allow fitment of performance manifolds with<br />
larger primary pipes.<br />
Manifold to cylinder head gasket . . . . . . . . . . . . .TMG10836 . . . .£3.95<br />
GEX7661<br />
Rear silencer fittings<br />
PME48<br />
PME49<br />
Early Minis used rubber blocks to hang the original exhausts from. The Play<br />
Mini range uses the later type of hook brackets and rubber hangers. These<br />
fitting kits contain all components, including the hanger conversion<br />
brackets, to allow easy installation. Simply use hanging rubbers for late cars.<br />
Fitting kit side exit . . . . . . . . . . . . . . . . . . . . . . . .WPE3003X . . .£41.95<br />
Fitting kit centre exit . . . . . . . . . . . . . . . . . . . . . .WPE3002X . . .£27.95<br />
Subframe hanger bracket front . . . . . . . . . . . . . . .PME48 . . . . . .£14.20<br />
Subframe hanger bracket rear . . . . . . . . . . . . . . . .PME49 . . . . . .£14.10<br />
Hanging rubber . . . . . . . . . . . . . . . . . . . . . . . . . .GEX7661 . . . . .£3.95<br />
Catalytic converter gasket . . . . . . . . . . . . . . . . . . .GEX7761 . . . . .£4.40<br />
Heat shield<br />
GAC184<br />
Radiant heat coming through the floors and bulkhead can make the cockpit<br />
of your Mini a hot place to be. Insulating the floors and bulkhead not only<br />
keeps the heat out but it can also prevent damage to carpets, paintwork and<br />
interior fittings where exhaust pipes, silencers and catalytic convertors are in<br />
close proximity to the panelwork.<br />
Exhaust heat shield can be used on the underside of the floors where the<br />
exhaust runs close to the floor particularly above silencers and catalytic<br />
convertors. It effectively reflects 90% of the radiant heat from exhausts and<br />
can withstand temperatures up to 1000°C. The general purpose material can<br />
be used to cover bulkheads and floors to keep general heat transfer to the<br />
cockpit to a minimum. It can also be used to wrap and cover components in<br />
the engine bay to prevent heat damage.<br />
Exhaust heat shield 40” x 24” . . . . . . . . . . . . . . .GAC184 . . . . .£78.95<br />
General heat shield 1m x 1m . . . . . . . . . . . . . . . .GAC185 . . . . .£71.95<br />
High temperature adhesive . . . . . . . . . . . . . . . . . .GAC9908X . . . .£8.45<br />
The Magic Pipe... designed to fit to the<br />
original cast manifold but will enable<br />
you to fit most of our systems to your Classic Mini.<br />
Play Mini stainless steel - magic pipe<br />
PME43M<br />
For those of you who don’t want to fit an LCB manifold to the car this pipe<br />
is designed to fit to the original cast manifold but will enable you to fit most<br />
of our systems to your car. Please note this pipe is for carb models only.<br />
Down pipe - magic pipe . . . . . . . . . . . . . . . . . . . .PME43M . . . .£46.96<br />
Manifold clamp . . . . . . . . . . . . . . . . . . . . . . . . . .GEX7046 . . . . .£2.24<br />
Exhaust clamp 2” . . . . . . . . . . . . . . . . . . . . . . . . .GEX9009 . . . . .£0.85<br />
A14