Blacksmith Metalsmith Knifemaker Farrier Blacksmith ... - Pieh Tool
Blacksmith Metalsmith Knifemaker Farrier Blacksmith ... - Pieh Tool
Blacksmith Metalsmith Knifemaker Farrier Blacksmith ... - Pieh Tool
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
KNIFEMAKER, BLACKSMITH FORGES<br />
Mankel Knife Maker 2-Burners<br />
Open End with Round Bottom<br />
2-Burner<br />
shown with<br />
sides out<br />
Sides<br />
come<br />
out.<br />
Mankel Knife Maker 3-Burners<br />
Open End with Round Bottom<br />
NC Daddy #2, Open End Ports<br />
NC Daddy #2, Front and Back Ports<br />
KNIFEMAKER GAS FORGES<br />
Mankel Wt.<br />
MKOE2RP Knife Maker with Open End 185 lb<br />
2 Burners Round Bottom, 115v Blower, Propane<br />
MKOE2RN Knife Maker with Open End 185 lb<br />
2 Burners Round Bottom, 115v Blower, Natural Gas<br />
After the forge is preheated the two burners allow the temperature to reach 2600 degrees F! By<br />
removing the side bricks, the forge can be open from 3 sides making this the most versatile of<br />
the <strong>Knifemaker</strong> Forges. The forge top is lined with Thermotect A Board and the bottom is poured<br />
refractory cement with radius on the floor. Forge is fabricated of formed steel. It is tough-will take<br />
just about any abuse. It is also extremely easy to repair. Supplied with manifold, complete with<br />
orifices, regulator with pressure gauge and 8 ft. hose (differs if ordering Natural Gas).<br />
Outside Case Dimensions Opening w/ends in<br />
high wide wide deep<br />
12” 20” 16” 2”<br />
MKO3RP Knife Maker with Open End 195 lb<br />
3 Burners Round Bottom, 115v Blower, Propane<br />
MKO3RN Knife Maker with Open End 195 lb<br />
3 Burners Round Bottom, 115v Blower, Natural Gas<br />
After the forge is preheated the three burners allow the temperature to reach 2600 degrees F!<br />
By removing the side bricks, the forge can be open from 3 sides making this the most versatile of<br />
the <strong>Knifemaker</strong> Forges. The forge top is lined with Thermotect A Board and the bottom is poured<br />
refractory cement with radius on the floor. Forge is fabricated of formed steel. It is tough-will take<br />
just about any abuse. It is also extremely easy to repair. Supplied with manifold, complete with<br />
orifices, regulator with pressure gauge and 8 ft. hose (differs if ordering Natural Gas).<br />
Outside Case Dimensions Opening w/ends in<br />
high wide wide deep<br />
12” 20” 16” 2”<br />
Mankel Accessories<br />
MOM Mankel Orifice & Mixer (Specify LP or NG)<br />
MHOSE-8 Mankel Hose 8’ (LP)<br />
MBrick Mankel Thermotect Board<br />
BLACKSMITH PROPANE FORGES<br />
NC<br />
Exclusive, high efficiency burners. Push-button ignition. Uniform Heat-Self Regulating to 2350°.<br />
Quick Recovery-heats and reheats metal very quickly. Flexible-rear bar stock door allows heating<br />
sections of bar stock. (Optional on some models) No Blower Required.<br />
May be configured for natural gas. Transportable-light weight and quick cooling.<br />
Item # Wt.<br />
NCDAD2-OE Daddy #2, Open End Ports<br />
3 Burners, Propane<br />
73 lb<br />
NCDAD2 Daddy #2, Open Front and Back<br />
3 Burners, Propane<br />
73 lb<br />
So many forges have such small fireboxes. Not the Daddy! It features a 12 inch long and 6 inch high<br />
firebox! Imagine all the nice big pieces you can work with in this forge. The barstock port in the front<br />
and back door is great for isolated heats. The side ports make heating long bar a snap. Work metal<br />
bar from either end and straight out through the other side when long heat is required in the middle<br />
of the bar - will accommodate large stacks of metal for production work. Hose, gauge, and regulator<br />
included.<br />
Inside Dimensions Door/Openings<br />
wide high deep wide high<br />
12” 6” 9” 3” 2”<br />
NCLB-OE Lowboy, Open End Ports 65 lb<br />
3 Burners, Propane<br />
The Low Boy has an insulated door and 2 side bar stock ports. Has rapid heat recovery for quick<br />
turn around time. Ideal for competition shoe making and blacksmithing. <strong>Knifemaker</strong>s - this is the<br />
one to use for Damascus blade forging!<br />
Inside Dimensions Door/Openings<br />
wide high deep wide high<br />
12” 3” 9” 3” 2”<br />
Have you considered taking an artistic blacksmithing class at <strong>Pieh</strong> <strong>Tool</strong>?<br />
NC Lowboy, Open End Ports<br />
82 1-888-743-4866 <strong>Pieh</strong> <strong>Tool</strong> Company, Inc.