Blacksmith Metalsmith Knifemaker Farrier Blacksmith ... - Pieh Tool
Blacksmith Metalsmith Knifemaker Farrier Blacksmith ... - Pieh Tool
Blacksmith Metalsmith Knifemaker Farrier Blacksmith ... - Pieh Tool
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
POWER HAMMER SWAGES, TEXTURING<br />
Spring Swages<br />
<strong>Pieh</strong> Legacy Collection <br />
Victory Forge<br />
Item #<br />
VFGR58 Grape, 5/8"<br />
VFBA38 Ball, 3/8”<br />
VFBA12 Ball, 1/2”<br />
VFBA58 Ball, 5/8"<br />
VFBA34 Ball, 3/4"<br />
Acorn Swage<br />
VFRO38 Rope, 3/8"<br />
VFRO12 Rope, 1/2"<br />
VFAC38 Acorn, 3/8"<br />
VFAC12 Acorn, 1/2”<br />
VFAC58 Acorn, 5/8”<br />
VFAC1 Acorn, 1”<br />
Tenon Swage<br />
VFTE18 Tenon, 3/16”<br />
VFTE14 Tenon, 1/4”<br />
VFTE38 Tenon, 3/8”<br />
VFTE58 Tenon, 5/8"<br />
Victory Forge Leaf <strong>Tool</strong>s<br />
VFVTR Vine Texture Swage<br />
Gives a nice wood texture. Made for round stock.<br />
VFLB38 Leaf Blank, 3/8” Swage<br />
VFLB12 Leaf Blank, 1/2” Swage<br />
VFL<strong>Tool</strong> Leaf Sinking <strong>Tool</strong><br />
VFB<strong>Tool</strong> Butt <strong>Tool</strong><br />
Use these together: forge your leaf using Leaf Blank<br />
Swage, center bottom side over the Leaf Sink <strong>Tool</strong><br />
with veining chisel. Heat, turn over, strike Butt <strong>Tool</strong><br />
over raised crease, sinking leaf into a wood stump.<br />
Grape Swage<br />
Ball Swage<br />
Guillotine Fullers<br />
<strong>Pieh</strong> Legacy Collection<br />
Victory Forge<br />
Fits in anvil’s hardy hole. Simple to use! Just give a few blows to<br />
the top of the fuller while turning your stock and turn out some nice<br />
fullered pieces. Made in the USA.<br />
Item #<br />
VFGF58 Guillotine Fuller, 5/8”<br />
VFGF34 Guillotine Fuller, 3/4”<br />
VFGF78 Guillotine Fuller, 7/8"<br />
VFGF1 Guillotine Fuller, 1”<br />
VFGCF58 Guillotine Combo Fuller, 5/8”<br />
VFGCF34 Guillotine Combo Fuller, 3/4”<br />
VFGCF78 Guillotine Combo Fuller, 7/8”<br />
VFGCF1 Guillotine Combo Fuller, 1”<br />
Nail Headers<br />
<strong>Pieh</strong> Legacy Collection<br />
Nail making is one of the very oldest forms of forging. Square hand made nails<br />
have 4 times the holding power as a round wire nail. It is a great way to learn<br />
better hammer control. To make nails start with a round or square rod usually<br />
in a size from 3/16 up to say 1/4 inch in either diameter or square. The ideal<br />
material would be very low carbon steel but we can make good nails from<br />
either hot or cold rolled mild steel. Domed, 4140 Steel. Made in the USA.<br />
<strong>Pieh</strong><br />
Item #<br />
CDNH316 <strong>Pieh</strong> Nail Header, 3/16”<br />
CDNH14 <strong>Pieh</strong> Nail Header, 1/4”<br />
Scroll Jig<br />
<strong>Pieh</strong> Legacy Collection<br />
This handy scroll jig will allow you to make a perfect<br />
4-1/2” scroll every time. Just clamp it in the vise and<br />
shape your stock around the scroll. Made of mild steel.<br />
Victory Forge<br />
Item #<br />
VF68 Scrolling Jig, 1/4” x 1”<br />
Victory Forge Springs Swages are made from mild steel by our<br />
resident blacksmith instructor, Gordon Williams. Be assured<br />
each tool is crafted carefully; your satisfaction is guaranteed!<br />
Ask us about modifying your swage to fit your power hammer!<br />
Check out our other fine tools in the <strong>Pieh</strong> Legacy Collection TM .<br />
As a general rule, our spring swages are designed for use on<br />
square stock. Square stock produces the best results because<br />
there is more material to displace. They will work on round as<br />
well, but will not turn out as nicely-sometimes requiring more<br />
clean up on the piece produced. If we make a swage for round<br />
specifically, we will indicate it.<br />
Rope Swage Leaf Blank Swage Vine Texture Swage<br />
VF Butt <strong>Tool</strong><br />
(close up view)<br />
VF Leaf <strong>Tool</strong><br />
Spring swages can be used by hand at the anvil or power<br />
hammer. They will produce better results if you build a<br />
saddle, to go over a power hammer die, with a hardy hole<br />
in it and weld a hardy stob onto the spring swage. This<br />
hardy stob will also allow the spring swage to be used in<br />
the hardy hole of your anvil.<br />
If you would like more instruction on making leaves<br />
consider taking our 3 day blacksmithing class.<br />
Guillotine Fuller<br />
The double fullering allows you to make chile peppers or making<br />
bamboo on tubing, as well as fullering leaf stems.<br />
Power Hammer Punch Set<br />
<strong>Pieh</strong> Legacy Collection<br />
Item #<br />
PT-S715S <strong>Pieh</strong> 15 Piece Punch Set with Rivet Tong<br />
Set is designed to be used with our 1/2” rivet tong under heavy<br />
forging equipment such as an air hammer, treadle hammer or other<br />
trip hammer. Also included, the handsome composite wood tool block<br />
keeps tools organized. *The Hot Cut Chisel will need to be dressed at<br />
the belt sander/grinder to individual preference. Made in the USA.<br />
Made from S7 and includes 1 each of the following:<br />
• Veining Chisel, Small<br />
• Veining Chisel, Large<br />
• 15/64” (6mm) Ball (Bob) Punch<br />
• 21/64” (8.5mm) Ball (Bob) Punch<br />
• 3/8” (10mm) Ball (Bob) Punch<br />
• 19/64” (7.5mm) Ball (Bob) Punch<br />
• 23/64” (9.5mm) Ball (Bob) Punch<br />
• 1/2” (13mm) Ball (Bob) Punch<br />
Guillotine Combo Fuller<br />
• 3/16” Mushroom Punch<br />
• 5/16” (8mm) Round Tapered Punch<br />
• 25/64” (10mm) Round Tapered Punch<br />
• 15/32” (12mm) Round Tapered Punch<br />
• 13/64” (10mm) Fuller<br />
• 5/32” (8mm) Fuller<br />
• 15/64” (12mm) Fuller<br />
• 3/4” Billy Rivet Tong: #PT4012<br />
Punch shown with Tong<br />
76 1-888-743-4866 <strong>Pieh</strong> <strong>Tool</strong> Company, Inc.