Blacksmith Metalsmith Knifemaker Farrier Blacksmith ... - Pieh Tool
Blacksmith Metalsmith Knifemaker Farrier Blacksmith ... - Pieh Tool
Blacksmith Metalsmith Knifemaker Farrier Blacksmith ... - Pieh Tool
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
Repousse Supplies<br />
Item #<br />
PB8 Pitch Bowl, 8”<br />
Cast iron pitch bowl. Bottom is slightly flat. Use with our rubber ring pad.<br />
Made in India.<br />
PBPR Rubber Ring Pad<br />
Pad fits our 8 inch pitch bowl. Fits under the bowl allowing you to rotate it<br />
as needed.<br />
RGP Red German Pitch, 2 kg<br />
Pitch is used for chasing and repousse. Red German Pitch isn’t brittle<br />
and is forgiving. It is far less toxic and easier to use than black pitch and<br />
yields better results. Comes in 2 kg bread pan like container. It melts at a<br />
relatively low temperature and can be safely manipulated and shaped by<br />
hand. *One 2 kg container will not fill bowl completely. Splashing concrete<br />
in the bottom will remedy this.<br />
PBK8 8” Pitch Bowl Kit<br />
This kit contains an 8 inch cast iron pitch bowl, the proper sized rubber pitch<br />
bowl pad, and a 2 kg bar of the finest quality Red (hard) German pitch. Pitch<br />
bowl and pad made in India. Warning: One 2 kilo loaf of pitch will not fill<br />
this pitch bowl full. It will be shy a 1/4 inch or so. You will need to either buy<br />
a second 2 kilo loaf or splash a little “quick concrete” in the bottom of your<br />
bowl first. If you do this, you will have enough and may even have some extra.<br />
Chasing & Repousse <strong>Tool</strong>s<br />
Peddinghaus<br />
Item #<br />
0095010000 Chasing Design Set<br />
This 10 piece chasing set is used mainly by tinsmiths to leave impressions<br />
in metals such as tin, copper, brass, etc. Each tool is a different design and<br />
are 4” long.<br />
<strong>Pieh</strong> Legacy Collection TM<br />
Overall length is approximately 4-1/2”.<br />
Made from W-1 tool steel. Made in USA.<br />
Item #<br />
PTChaseS1 <strong>Pieh</strong> Chasing Set #1<br />
The <strong>Pieh</strong> <strong>Tool</strong> Chasing Set #1 includes 6 tools:<br />
• 1 Thick Liner ¼”<br />
• 1 Rectangle Push <strong>Tool</strong> ¼”<br />
• 1 Thick Liner 3/16”<br />
• 1 Square Planisher 3/8”<br />
• 1 Push <strong>Tool</strong> 3/8”<br />
• 1 Oblong Push <strong>Tool</strong><br />
PTChaseS2 <strong>Pieh</strong> Chasing Set #2<br />
The <strong>Pieh</strong> <strong>Tool</strong> Chasing Set #2 includes 12 tools:<br />
• 4 Half Rounds: 3/16”, 1/4” (2), and 7/16”<br />
• 1 Half Round Planisher 1/8”<br />
• 1 Rhombus (Flat): 1/8”<br />
• 1 Push <strong>Tool</strong> (Round) 3/16”<br />
• 1 Round (Flat) 3/16”<br />
• 1 Thin Liner: 3/16”<br />
• 1 Thin Liner (Double sided bevel) 3/16”<br />
• 1 Thick Liner: 7/16”<br />
• 1 Thick Liner (Double sided bevel): 7/16”<br />
PTChaseS3 <strong>Pieh</strong> Chasing Set #3<br />
The <strong>Pieh</strong> <strong>Tool</strong> Chasing Set #3 includes 20 tools:<br />
• 7 Half Rounds: 3/16” (3), 1/4” (2), 7/16” and 1/2”<br />
• 1 Half Round Planisher 1/8”<br />
• 2 Rhombus (Flat): 1/8” and 3/16”<br />
• 1 Push <strong>Tool</strong> (Round) 3/16”<br />
• 1 Round (Flat) 3/16”<br />
• 2 Thin Liners: 3/16” and 1/4”<br />
• 2 Thin Liners (Double sided bevel) 3/16” and 1/4”<br />
• 2 Thick Liners: 7/16” and 1/2”<br />
• 2 Thick Liners (Double sided bevel): 7/16” and 1/2”<br />
*Please note that 12 of these tools are from Set #2. If<br />
you have already purchased Set #2 and would like to<br />
order only the 8 New tools you may do so now. They<br />
are listed at the right.<br />
REPOUSSE TOOLS<br />
<strong>Pieh</strong> <strong>Tool</strong><br />
Chasing Set #1<br />
<strong>Pieh</strong> <strong>Tool</strong> Chasing Set #2<br />
<strong>Pieh</strong> <strong>Tool</strong> Chasing Set #3<br />
Pitch Bowl, Ring Repousse Technique Repousse Cup & Turtle<br />
& Pitch<br />
by Bonnie Harvey<br />
Instructions: Wrap the pitch in several layers of heavy cloth or in a few<br />
plastic bags and moderately hit it a few times with a heavy hammer and<br />
place in the pitch bowl; then heat slowly in a 250 or 300 degree oven.<br />
Over-heated pitch will become brittle once it’s cooled again and<br />
may become useless. If overheated, remove the burnt area immediately<br />
to avoid further contamination of the pitch bowl. Once the pitch is<br />
melted let the pitch air-cool for several hours. When you are doing<br />
repousse soften pitch with a heat gun when ready to flip your piece.<br />
We recommend you dip your fingers in water before attempting to<br />
handle hot pitch. If the surface of the pitch appears glossy, it is<br />
too hot to touch. We recommend putting chap stick on the back of<br />
your piece to keep pitch from sticking.<br />
Peddinghaus<br />
10 piece<br />
Chasing Set<br />
<strong>Pieh</strong> <strong>Tool</strong><br />
Chasing Set<br />
#4 (1 of 6)<br />
Diagram of the tool ends in<br />
<strong>Pieh</strong> Chasing Set #3<br />
We offer<br />
Chasing and Repousse<br />
Books: pages 112-114<br />
DVD’s: pages 127<br />
Item #<br />
PTChaseS4 Chasing Set #4<br />
The <strong>Pieh</strong> <strong>Tool</strong> Chasing Eye Set includes 6 tools:<br />
• 1 each: 1/8” Round and Oval<br />
• 1 each: 3/16” Round and Oval<br />
• 1 each: 9/32” Round and Oval<br />
<strong>Pieh</strong> <strong>Tool</strong> Chasing <strong>Tool</strong>s Eye punches are the easy<br />
way to make perfect eyes. After you have identified<br />
the facial features, simply position the proper size<br />
eye punch and rotate while pushing on the handle.<br />
The result is a perfectly formed round eye. The<br />
round punches are mainly used on human figures<br />
and the oval punches are mainly used on animal<br />
figures. Overall length is approximately 3-1/2”<br />
Made from W-1 tool steel. Made in USA.<br />
• These tools are designed to be used in wood<br />
but may also be used in metal. • You may want<br />
to relieve the edges if they are to sharp for certain<br />
designs and materials.<br />
Individual Chasing <strong>Tool</strong>s<br />
Overall length is approximately 4-1/2”. Made<br />
from W-1 tool steel. Made in USA.<br />
Item #<br />
PTChaseHR5.0 <strong>Pieh</strong> Half Round 1/2”<br />
PTChaseHRT.19 <strong>Pieh</strong> Half Round 3/16” Thin<br />
PTChaseHRTH.19 <strong>Pieh</strong> Half Round 3/16” Thick<br />
PTChaseRh.19 <strong>Pieh</strong> Rhombus 3/16”<br />
PTChaseTH.438 <strong>Pieh</strong> Thick Liner 7/16”<br />
PTChaseTH5.0 <strong>Pieh</strong> Thick Liner 1/2”<br />
PTChaseTHDS5.0 <strong>Pieh</strong> Thick Liner 1/2”<br />
Double Sided<br />
PTChaseTL1.88 <strong>Pieh</strong> Thin Liner 3/16”<br />
PTChaseTL.25 <strong>Pieh</strong> Thin Liner1/4”<br />
PTChaseTLDS.25 <strong>Pieh</strong> Thin Liner 1/4”<br />
Double Sided<br />
<strong>Pieh</strong> <strong>Tool</strong> Company, Inc. 1-888-743-4866 55