Blacksmith Metalsmith Knifemaker Farrier Blacksmith ... - Pieh Tool

More documents

Recommendations

Info

SWAGES, FULLERS, DRIFTS, PUNCHES Swages Peddinghaus Item # *Special Order Items 5048020010 Top 10mm (.39”) handled 5048020015 Top 15mm (.59”) handled 5048020020 Top 20mm (.79”) handled 5049010010 Bottom 10mm (.39”) 7/8” 5049010015 Bottom 15mm (.59”) 7/8” 5049010020 Bottom 20mm (.79”) 7/8” Fullers Peddinghaus *Special Order Items 5054020015 Top 15mm (.59”) handled 5054020020 Top 20mm (.79”) handled 5055010015 Bottom 15mm (.59”) 7/8” 5055010020 Bottom 20mm (.79”) 7/8” Flatters Peddinghaus 5050020060 60mm (2.50”), handled 5050020070 70mm, (2.75”), handled Set Hammers Peddinghaus *Special Order Item 5052020000 Set Hammer, 51mm (2”) handled (Use with 5033010000 Anvil Block) Center Punches Pieh Legacy Collection TM Item # PCP000 Pyramid Punch, 7” long CP000 Center Punch, 7” long Both made from 1/2” round S7 tool steel. Flatland Forge CNTRP1 Center Punch, 7” long Made from 4140 steel. Peddinghaus 6612110130 Center Punch, 10x120mm 6612110162 Center Punch, 12x150mm 6612110164 Center Punch, 14x150mm 6624110250 Center Punch, 15x250mm Made of chrome-molybdenum air-hardened steel with non-spread heads. Hand Fullers Pieh Legacy Collection TM Item # FP125 Pieh Fuller Small, 1/8” FP250 Pieh Fuller Medium, 1/4” FP375 Pieh Fuller Large, 3/8” Made from 5/8” S7 round stock, 7” long. Ball Punches Pieh Legacy Collection TM Made from 1/2” round S7 tool steel, 7” long. Item # BP125 Ball 1/8” BP188 Ball 3/16” BP250 Ball 1/4” BP312 Ball 5/16” BP375 Ball 3/8” BP437 Ball 7/16” BP500 Ball 1/2” BallP7 Set of 7 Ball Punches ToolHolder-12 Denim Tool Roll, 12 Pocket BP625 Ball 5/8” BPD625 Ball Dimpled 5/8” BP750 Ball 3/4” BPD750 Ball Dimpled 3/4” Top Fuller Top Swage Bottom Swage Bottom Fuller Flatter Pieh Tool Center Punch Flatland Center Punch Peddinghaus Center Punch Small, Medium, Large Fullers Ball Punch Dimpled Set Hammer Pieh Tool Pyramid Center Punch 1/8” 3/16” 1/4” 5/16” 3/8” 7/16” 1/2” Anvil Block Peddinghaus Item # *Special Order Items 5053010000 Bottom Block, (51mm) 2” 7/8” Shank. Used with their Set Hammer. Round Punches Peddinghaus Special Order Item 5056020010 10mm handled 5056020015 15mm handled 5056020020 20mm handled Vise Wedge Pieh Legacy Collection TM VW100 Pieh Vise Wedge Drift Punches Pieh Legacy Collection TM Item # DP188 Pieh Drift 3/16” DP250 Pieh Drift 1/4” DP312 Pieh Drift 5/16” DP375 Pieh Drift 3/8” DP437 Pieh Drift 7/16” DP500 Pieh Drift 1/2” A33Set Set of all 6 Pieh Drifts Made from 5/8” H13 tool steel. They are 8” long with a tapered drift of approximately 3”. The handle area is smooth for a comfortable grip. The set is discounted offering you savings. Order our handy tool roll with this set now and save 20% on the tool roll. *Note: These cannot be quenched in water. The Veining Chisel we offer in our set is shown on page 53. See Iron Menagerie Book for step-by-step projects, BK68, page 98. Wizard Eye Socket Eagle Eye Anvil Block Round Punch The Pieh Tool vise wedge compliments our S7 animal head and character punch sets. In the book Iron Menagerie, you will find a number of projects. The vise wedge is needed in some of the projects. Of course its uses are endless. Made from mild steel from welded angle bar and painted black. The bottom portion should be placed securely in a vise leaving the angle wedge on top. Peddinghaus Drift Peddinghaus Item # 6608110001 Drift 10x1 6608110003 Drift 10x3 6608110004 Drift 10x4 6608110005 Drift 12x5 6608110008 Drift 12x8 6608110010 Drift 12x10 6608110012 Drift 14x12 Made of chrome-molybdenum air-hardened steel with non-spread heads. Eye/Ear Punches Pieh Legacy Collection TM Item # EP250 Round Eye 1/4” EP125 Round Eye 1/8” EP188 Round Eye 3/16” EyeP3 Set of 3 Eye Punches ES500 Eye Socket WE000 Wolf Eye DE000 Duck Eye EE000 Eagle Eye HE000 Horse Head Ear S7Set20 Set of all 20 S7 Tools Set Includes: 7 Ball, 3 Round Eye, Center, Wizard Eye Socket, Duck Eye, Wolf Eye, Eagle Eye, Horse Head Ear, Veining Chisel, and 3 Fullers. H13 Drift Set Tool Roll Eyes: 1/8”, 1/4”, 3/16” Horse Head Ear Vise Wedge Item # ToolHolder Tool Roll, 20p ToolHolder-12 Tool Roll, 12p Our 20 & 12 Pocket Denim Tool Rolls will keep your tools organized. *When you order one with the S7 20 Piece or 6 Piece Drift Set you will save 20% on the roll. Colors vary. 54 1-888-743-4866 Pieh Tool Company, Inc. Wolf Eye Duck Eye
Repousse Supplies Item # PB8 Pitch Bowl, 8” Cast iron pitch bowl. Bottom is slightly flat. Use with our rubber ring pad. Made in India. PBPR Rubber Ring Pad Pad fits our 8 inch pitch bowl. Fits under the bowl allowing you to rotate it as needed. RGP Red German Pitch, 2 kg Pitch is used for chasing and repousse. Red German Pitch isn’t brittle and is forgiving. It is far less toxic and easier to use than black pitch and yields better results. Comes in 2 kg bread pan like container. It melts at a relatively low temperature and can be safely manipulated and shaped by hand. *One 2 kg container will not fill bowl completely. Splashing concrete in the bottom will remedy this. PBK8 8” Pitch Bowl Kit This kit contains an 8 inch cast iron pitch bowl, the proper sized rubber pitch bowl pad, and a 2 kg bar of the finest quality Red (hard) German pitch. Pitch bowl and pad made in India. Warning: One 2 kilo loaf of pitch will not fill this pitch bowl full. It will be shy a 1/4 inch or so. You will need to either buy a second 2 kilo loaf or splash a little “quick concrete” in the bottom of your bowl first. If you do this, you will have enough and may even have some extra. Chasing & Repousse Tools Peddinghaus Item # 0095010000 Chasing Design Set This 10 piece chasing set is used mainly by tinsmiths to leave impressions in metals such as tin, copper, brass, etc. Each tool is a different design and are 4” long. Pieh Legacy Collection TM Overall length is approximately 4-1/2”. Made from W-1 tool steel. Made in USA. Item # PTChaseS1 Pieh Chasing Set #1 The Pieh Tool Chasing Set #1 includes 6 tools: • 1 Thick Liner ¼” • 1 Rectangle Push Tool ¼” • 1 Thick Liner 3/16” • 1 Square Planisher 3/8” • 1 Push Tool 3/8” • 1 Oblong Push Tool PTChaseS2 Pieh Chasing Set #2 The Pieh Tool Chasing Set #2 includes 12 tools: • 4 Half Rounds: 3/16”, 1/4” (2), and 7/16” • 1 Half Round Planisher 1/8” • 1 Rhombus (Flat): 1/8” • 1 Push Tool (Round) 3/16” • 1 Round (Flat) 3/16” • 1 Thin Liner: 3/16” • 1 Thin Liner (Double sided bevel) 3/16” • 1 Thick Liner: 7/16” • 1 Thick Liner (Double sided bevel): 7/16” PTChaseS3 Pieh Chasing Set #3 The Pieh Tool Chasing Set #3 includes 20 tools: • 7 Half Rounds: 3/16” (3), 1/4” (2), 7/16” and 1/2” • 1 Half Round Planisher 1/8” • 2 Rhombus (Flat): 1/8” and 3/16” • 1 Push Tool (Round) 3/16” • 1 Round (Flat) 3/16” • 2 Thin Liners: 3/16” and 1/4” • 2 Thin Liners (Double sided bevel) 3/16” and 1/4” • 2 Thick Liners: 7/16” and 1/2” • 2 Thick Liners (Double sided bevel): 7/16” and 1/2” *Please note that 12 of these tools are from Set #2. If you have already purchased Set #2 and would like to order only the 8 New tools you may do so now. They are listed at the right. REPOUSSE TOOLS Pieh Tool Chasing Set #1 Pieh Tool Chasing Set #2 Pieh Tool Chasing Set #3 Pitch Bowl, Ring Repousse Technique Repousse Cup & Turtle & Pitch by Bonnie Harvey Instructions: Wrap the pitch in several layers of heavy cloth or in a few plastic bags and moderately hit it a few times with a heavy hammer and place in the pitch bowl; then heat slowly in a 250 or 300 degree oven. Over-heated pitch will become brittle once it’s cooled again and may become useless. If overheated, remove the burnt area immediately to avoid further contamination of the pitch bowl. Once the pitch is melted let the pitch air-cool for several hours. When you are doing repousse soften pitch with a heat gun when ready to flip your piece. We recommend you dip your fingers in water before attempting to handle hot pitch. If the surface of the pitch appears glossy, it is too hot to touch. We recommend putting chap stick on the back of your piece to keep pitch from sticking. Peddinghaus 10 piece Chasing Set Pieh Tool Chasing Set #4 (1 of 6) Diagram of the tool ends in Pieh Chasing Set #3 We offer Chasing and Repousse Books: pages 112-114 DVD’s: pages 127 Item # PTChaseS4 Chasing Set #4 The Pieh Tool Chasing Eye Set includes 6 tools: • 1 each: 1/8” Round and Oval • 1 each: 3/16” Round and Oval • 1 each: 9/32” Round and Oval Pieh Tool Chasing Tools Eye punches are the easy way to make perfect eyes. After you have identified the facial features, simply position the proper size eye punch and rotate while pushing on the handle. The result is a perfectly formed round eye. The round punches are mainly used on human figures and the oval punches are mainly used on animal figures. Overall length is approximately 3-1/2” Made from W-1 tool steel. Made in USA. • These tools are designed to be used in wood but may also be used in metal. • You may want to relieve the edges if they are to sharp for certain designs and materials. Individual Chasing Tools Overall length is approximately 4-1/2”. Made from W-1 tool steel. Made in USA. Item # PTChaseHR5.0 Pieh Half Round 1/2” PTChaseHRT.19 Pieh Half Round 3/16” Thin PTChaseHRTH.19 Pieh Half Round 3/16” Thick PTChaseRh.19 Pieh Rhombus 3/16” PTChaseTH.438 Pieh Thick Liner 7/16” PTChaseTH5.0 Pieh Thick Liner 1/2” PTChaseTHDS5.0 Pieh Thick Liner 1/2” Double Sided PTChaseTL1.88 Pieh Thin Liner 3/16” PTChaseTL.25 Pieh Thin Liner1/4” PTChaseTLDS.25 Pieh Thin Liner 1/4” Double Sided Pieh Tool Company, Inc. 1-888-743-4866 55
Page 1 and 2:
Blacksmith Metalsmith Knifemaker Fa
Page 3 and 4:
TABLE OF CONTENTS Price List . . .
Page 5 and 6:
HORSESHOE NAILS Manufactured from h
Page 7 and 8: Mustad MUD (Traction Nail) Used to
Page 9 and 10: Saddle (Keg) Wide Web St. Croix EZ
Page 11 and 12: Saddle (Keg) Concave Kerckhaert Tri
Page 13 and 14: Therapeutic Natural Balance The Nat
Page 15 and 16: Smooth Walker Rubber Shoes Smooth W
Page 17 and 18: Wide Web KB WEDGE KB Horseshoes tak
Page 19 and 20: HOOF STANDS, SHOEING BOXES Hoof Sta
Page 21 and 22: Bar Wedge Pads Castle Black Plastic
Page 23 and 24: Cushion Heel Pads Item # U/M CCH Ca
Page 25 and 26: ANTI-FUNGAL, CRACK & HOOF REPAIR An
Page 27 and 28: Vettec Hoof Packing Item # 46160 So
Page 29 and 30: POULTICES, LINIMENTS, POLISHES Poul
Page 31 and 32: Dewormers Farnam Item # HHEIP Horse
Page 33 and 34: Farrier Aprons Leather - Continued
Page 35 and 36: Farrier Rasps Nicholson Item # 1815
Page 37 and 38: NIPPERS, NAIL PULLERS, PULL OFFS Ho
Page 39 and 40: Clinchers (continued) Lopez Item #
Page 41 and 42: BLACKSMITH & KNIFEMAKER APRONS Blac
Page 43 and 44: The Bill Pieh Resource for Metalwor
Page 45 and 46: ANVILS SPECIFICATIONS CHART ANVIL C
Page 47 and 48: Wilton Shop Vise NC Folding Stand w
Page 49 and 50: Rounding Hammers Pieh Legacy Collec
Page 51 and 52: SPECIALTY HAMMERS, LAPIDARY Special
Page 53 and 54: Chasing Raising 300g Picard Chasing
Page 55 and 56: Rectangular Stake Square Stake Crea
Page 57: Chisels Pieh Legacy Collection Pieh
Page 61 and 62: BLACKSMITHING & FARRIER TONGS Tongs
Page 63 and 64: RIVET SPECIFICATIONS, LAG BOLTS For
Page 65 and 66: Magnets Item # PM Pencil Magnet To
Page 67 and 68: Utility Tools, Saws Folding Jab Saw
Page 69 and 70: M18 Cordless LITHIUM-ION 1/2” Hig
Page 71 and 72: M12 Cordless LITHIUM-ION Copper Tub
Page 73 and 74: DRILL & DRIVER BITS/SAW BLADES Milw
Page 75 and 76: GRINDERS, BUFFERS, BENDERS Jet Grin
Page 77 and 78: Beverly Shears (Throatless) Beverly
Page 79 and 80: Free Form Forging Dies Item # LDC L
Page 81 and 82: Pein Anvil Die Set We use the Mark
Page 83 and 84: FLY PRESS ACCESSORIES & TOOLING Fly
Page 85 and 86: WELDING FLUXES, COMPOUNDS, INGOTS W
Page 87 and 88: Forgemaster When you are in the mar
Page 89 and 90: Johnson Gas Furnace Forges Versatil
Page 91 and 92: FARRIER PROPANE FORGES (continued)
Page 93 and 94: Ceramic Shell Burn-Out Furnaces Joh
Page 95 and 96: CLOTHING, SUSPENDERS & GIFTS Clothi
Page 97 and 98: BK469 Custom Knifemaking, McCreight
Page 99 and 100: BLACKSMITHING TECHNIQUES & PROJECTS
Page 101 and 102: BK959 Boone Wrought Iron, Plummer 7
Page 103 and 104: BK941 Make Your own Woodworking Too
Page 105 and 106: BLACKSMITHING DECORATIVE & SCULPTUR
Page 107 and 108: BK732 Fireplace Accessories, Meilac
Page 109 and 110:
BK808 Masterpieces of 18th Century
Page 111 and 112:
PATINAS & FINISHES BK976 *S/O Bronz
Page 113 and 114:
BK78 Heat Treatment, Selection, and
Page 115 and 116:
BK798 Mousehole Forge, Postman, Hat
Page 117 and 118:
BK192 Expose of Repousse for the Be
Page 119 and 120:
JEWELRY & PMC BK98 Beaded Chain Mai
Page 121 and 122:
DESIGN & STYLE BK927 Art Forms Plan
Page 123 and 124:
BK657 How to Sell What you Make, Ge
Page 125 and 126:
BK105 Natural Balance Hoof Care Boo
Page 127 and 128:
BOOKS OXEN & MULES, FARRIER INVOICE
Page 129 and 130:
ARMOR DVD53 Armorer’s Workshop Se
Page 131 and 132:
VIDEOS BLACKSMITHING, CHASING & REP
Page 133 and 134:
DVD56 Japanese Silk Wrapped Handles
Page 135 and 136:
PL12-0101 (Organized by page # then
Page 137 and 138:
Page 139 and 140:
Page 141 and 142:
Page 143 and 144:
Page 145 and 146:
Page 147 and 148:
Page 149 and 150:
Page 151 and 152:
Page 153 and 154:
Page 155 and 156:
Page 157 and 158:
Page 159 and 160:
MAILING ADDRESS (Must match Credit
Page 161:
Vol. 12-1 •
show all

Blacksmith Metalsmith Knifemaker Farrier Blacksmith ... - Pieh Tool

Create successful ePaper yourself

Delete template?

Save as template?