Heavy Duty Balanced Opposed Compressors - Ariel Corporation

More documents

Recommendations

Info

FOR MODELS: JGZ AND JGU SECTION 5 - MAINTENANCE 6. Wipe down piston rod with denatured alcohol after rod installation. 7. Clean head-end head or unloader components and steel gaskets with denatured alcohol. Do not use anti-seize compounds on the head-end head steel-gasket. Use a very thin film of oil when installing o-rings. Grease VVCP unloader stem threads at the grease fitting with 2 to 3 pumps of multi-purpose grease using a standard hand pump grease gun. Wipe off any excess grease on the exterior. 8. Compressor valves are provided from the manufacturer cleaned and preserved, and suitable for non-lube service. Valves need no additional cleaning, provided they are sealed in their original packaging and have not been contaminated. 9. Clean valve retainers, high clearance assemblies, valve caps and steel gaskets with denatured alcohol. Use only a very thin film of oil for valve cap o-rings. Do not lubricate valve steel-gaskets. 10.Assemble cleaned parts immediately, using clean gloves, to avoid contamination and corrosion. If cylinder will not see immediate service, see the Ariel Packager’s Standards, appendix, available on the Ariel Web site, www.arielcorp.com or contact Ariel for preservation instructions to ER-34. Use a small amount of Loctite 565 Pipe Sealant on male threads when installing pipe plugs. Use Never-Seez, Regular Grade when tightening the crosshead-balance nut in the usual manner. DANGER: Do not use Ariel non-lube compressor cylinders for oxygen service. 7/09 PAGE 5 - 67
FOR MODELS: JGZ AND JGU SECTION 5 - MAINTENANCE BEARING LOG FORM/CONDITIONS AFTER REPLACING BEARINGS SERIAL NO. F- MODEL Date CRANKSHAFT THRUST (END) CLEARANCE: CRANKSHAFT SERIAL NUMBER THRUST CLEARANCE, IN. (mm) CONNECTING ROD THRUST (SIDE) CLEARANCE, IN. (mm) THROW NUMBER: JACK CLEARANCES, IN. (mm) THROW NUMBER: MAIN BEARINGS CONN. ROD BEARINGS 1 2 3 4 5 6 1 2 3 4 5 6 If measured clearances exceed the tolerances in Section 1, after installing new bearings, contact your packager or Ariel before proceeding. DATE TIME RPM OIL PRESSURE FILTER INLET PSIG (BAR G ) OIL PRESSURE FILTER OUTLET PSIG (BAR G ) OIL TEMPERATURE INTO FRAME °F (°C) BEARING CAP TEMPERATURES, °F (°C), AFTER RUN TIME OF: THROW 1 2 3 4 5 6 10 MINUTES 1 HOUR 4 HOURS REMARKS MAIN ROD MAIN ROD MAIN ROD PAGE 5 - 68 7/09
Page 1 and 2:
ARIEL Heavy Duty Balanced Opposed C
Page 3 and 4:
FOR MODELS: JGZ AND JGU TABLE OF CO
Page 5 and 6:
Page 7 and 8:
Page 9 and 10:
FOR MODELS: JGZ AND JGU SECTION 1 -
Page 11 and 12:
Page 13 and 14:
Page 15 and 16:
Page 17 and 18:
Page 19 and 20:
Page 21 and 22:
Page 23 and 24:
Page 25 and 26:
Page 27 and 28:
Page 29 and 30:
Page 31 and 32:
Page 33 and 34:
Page 35 and 36:
Page 37 and 38:
Page 39 and 40:
Page 41 and 42:
Page 43 and 44:
Page 45 and 46:
Page 47 and 48:
Page 49 and 50:
Page 51 and 52:
Page 53 and 54:
Page 55 and 56:
Page 57 and 58:
Page 59 and 60:
Page 61 and 62:
Page 63 and 64:
Page 65 and 66:
Page 67 and 68:
FOR MODELS: JGZ AND JGU SECTION 4 L
Page 69 and 70:
Page 71 and 72:
Page 73 and 74:
Page 75 and 76:
Page 77 and 78:
Page 79 and 80:
Page 81 and 82:
Page 83 and 84:
Page 85 and 86:
Page 87 and 88:
Page 89 and 90:
Page 91 and 92:
Page 93 and 94:
Page 95 and 96:
Page 97 and 98:
Page 99 and 100:
Page 101 and 102:
Page 103 and 104:
Page 105 and 106:
Page 107 and 108:
Page 109 and 110:
Page 111 and 112:
Page 113 and 114:
Page 115 and 116:
Page 117 and 118:
Page 119 and 120:
Page 121 and 122:
Page 123 and 124:
Page 125 and 126:
Page 127 and 128:
Page 129 and 130:
Page 131 and 132:
Page 133 and 134:
Page 135 and 136:
Page 137 and 138: FOR MODELS: JGZ AND JGU SECTION 5 -
Page 187: FOR MODELS: JGZ AND JGU SECTION 5 -
Page 211: FOR MODELS: JGZ AND JGU SECTION 7 -
show all

Heavy Duty Balanced Opposed Compressors - Ariel Corporation

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?